diff --git a/config.txt b/config.txt
index 62c8fc8..74179d4 100644
--- a/config.txt
+++ b/config.txt
@@ -1,93 +1,18 @@
-# BrooklynR NXT Hybrid, The Blockchain Linux 5.20.x by Scare Crow
-# ===============================================================
-#
-# * Brooklyn NXT Sinclair current 5.20.14 
-# * BrooklynR NXT QortalOS Community 5.16.x LTS-LE
-# * V1.2.3 BrooklynR NXT GUI 5.16.x is based on GNOME community code
-# * V1.2 BrooklynR NXT GUI 5.16.x is based on LXQT community code
-# * V 1.0 is based off a variety of Desktops with Brooklyn The Moose 5.12.6
-# * V 1.0 Jaymen is based on headless R Kernel 5.13.10 LTS
-# * RussCade 1.0 is based on optimized BrooklynR for Qortal minting and game emulators
-# * V1.1 XFCE is based on  Brooklyn Jackwagon 5.12.10 LTS
-# * V1.1 MATE-LXDE is based on Brookltn Plumbus 5.12.10 LTS
-#
-# =======================================================
-# If this has helped you in any way then throw me some
-# LTC for R&D or a few gallons of petrol mixed with booze 
-# Personal LTC: LL5pThYz8z5zqjJVgnCkwHHWhmb72DtZpY
-# Personal QORT: QdiGEQEr17Jho5RZuhNhzPUX671DqKq3Xt
-#
-# -/ Scare Crowe
-#
-# Before I forget, fuck you T3Q. I hope you eat shit and die.
-#
-# For more options and information see
-# http://rpf.io/configtxt
-# Some settings may impact device functionality. See link above for details
-
-# uncomment if you get no picture on HDMI for a default "safe" mode
-#hdmi_safe=1
-
-# uncomment this if your display has a black border of unused pixels visible
-# and your display can output without overscan
-disable_overscan=1
-
-# uncomment the following to adjust overscan. Use positive numbers if console
-# goes off screen, and negative if there is too much border
-#overscan_left=16
-#overscan_right=16
-#overscan_top=16
-#overscan_bottom=16
-
-# uncomment to force a console size. By default it will be display's size minus
-# overscan.
-#framebuffer_width=1280
-#framebuffer_height=720
-
-# uncomment if hdmi display is not detected and composite is being output
-#hdmi_force_hotplug=1
-
-# uncomment to force a specific HDMI mode (this will force VGA)
-#hdmi_group=1
-#hdmi_mode=1
-
-# uncomment to force a HDMI mode rather than DVI. This can make audio work in
-# DMT (computer monitor) modes
-#hdmi_drive=2
-
-# uncomment to increase signal to HDMI, if you have interference, blanking, or
-# no display
-#config_hdmi_boost=4
-
-# uncomment for composite PAL
-#sdtv_mode=2
-
-#uncomment to overclock the arm. 700 MHz is the default.
-#arm_freq=800
-
-# Uncomment some or all of these to enable the optional hardware interfaces
-#dtparam=i2c_arm=on
-#dtparam=i2s=on
-#dtparam=spi=on
-
-# Uncomment this to enable infrared communication.
-#dtoverlay=gpio-ir,gpio_pin=17
-#dtoverlay=gpio-ir-tx,gpio_pin=18
-
-# Additional overlays and parameters are documented /boot/overlays/README
-#
-kernel=vmlinuz-5.60.12LTS-Sinclair_Titan+
-over_voltage=2
-arm_freq=1750
-#arm_boost=1
-#
-[pi4]
+kernel=vmlinuz-6.0.11-raziel-mempow-Torchie+
 max_framebuffers=2
-
-[all]
-dtoverlay=vc4-fkms-v3d
-gpu_mem=512
-gpu_freq=600
+hdmi_force_hotplug=1
+hdmi_drive=2
 dtparam=audio=on
-   hdmi_group=2
-   hdmi_mode=82
+display_auto_detect=1
+arm_64bit=1
+disable_overscan=1
+otg_mode=1
+arm_boost=1
+dtoverlay=vc4-kms-v3d
+gpu_mem=64
+hdmi_group=2
+hdmi_mode=82
+hdmi_group=2
+hdmi_mode=82
+
+[all]  # Settings after [all] will be applied to all hardware