forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
92 lines
2.5 KiB
92 lines
2.5 KiB
* NI XGE Ethernet controller |
|
|
|
Required properties: |
|
- compatible: Should be "ni,xge-enet-3.00", but can be "ni,xge-enet-2.00" for |
|
older device trees with DMA engines co-located in the address map, |
|
with the one reg entry to describe the whole device. |
|
- reg: Address and length of the register set for the device. It contains the |
|
information of registers in the same order as described by reg-names. |
|
- reg-names: Should contain the reg names |
|
"dma": DMA engine control and status region |
|
"ctrl": MDIO and PHY control and status region |
|
- interrupts: Should contain tx and rx interrupt |
|
- interrupt-names: Should be "rx" and "tx" |
|
- phy-mode: See ethernet.txt file in the same directory. |
|
- nvmem-cells: Phandle of nvmem cell containing the MAC address |
|
- nvmem-cell-names: Should be "address" |
|
|
|
Optional properties: |
|
- mdio subnode to indicate presence of MDIO controller |
|
- fixed-link : Assume a fixed link. See fixed-link.txt in the same directory. |
|
Use instead of phy-handle. |
|
- phy-handle: See ethernet.txt file in the same directory. |
|
|
|
Examples (10G generic PHY): |
|
nixge0: ethernet@40000000 { |
|
compatible = "ni,xge-enet-3.00"; |
|
reg = <0x40000000 0x4000 |
|
0x41002000 0x2000>; |
|
reg-names = "dma", "ctrl"; |
|
|
|
nvmem-cells = <ð1_addr>; |
|
nvmem-cell-names = "address"; |
|
|
|
interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; |
|
interrupt-names = "rx", "tx"; |
|
interrupt-parent = <&intc>; |
|
|
|
phy-mode = "xgmii"; |
|
phy-handle = <ðernet_phy1>; |
|
|
|
mdio { |
|
ethernet_phy1: ethernet-phy@4 { |
|
compatible = "ethernet-phy-ieee802.3-c45"; |
|
reg = <4>; |
|
}; |
|
}; |
|
}; |
|
|
|
Examples (10G generic PHY, no MDIO): |
|
nixge0: ethernet@40000000 { |
|
compatible = "ni,xge-enet-2.00"; |
|
reg = <0x40000000 0x6000>; |
|
|
|
nvmem-cells = <ð1_addr>; |
|
nvmem-cell-names = "address"; |
|
|
|
interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; |
|
interrupt-names = "rx", "tx"; |
|
interrupt-parent = <&intc>; |
|
|
|
phy-mode = "xgmii"; |
|
phy-handle = <ðernet_phy1>; |
|
}; |
|
|
|
Examples (1G generic fixed-link + MDIO): |
|
nixge0: ethernet@40000000 { |
|
compatible = "ni,xge-enet-2.00"; |
|
reg = <0x40000000 0x6000>; |
|
|
|
nvmem-cells = <ð1_addr>; |
|
nvmem-cell-names = "address"; |
|
|
|
interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>, <0 30 IRQ_TYPE_LEVEL_HIGH>; |
|
interrupt-names = "rx", "tx"; |
|
interrupt-parent = <&intc>; |
|
|
|
phy-mode = "xgmii"; |
|
|
|
fixed-link { |
|
speed = <1000>; |
|
pause; |
|
link-gpios = <&gpio0 63 GPIO_ACTIVE_HIGH>; |
|
}; |
|
|
|
mdio { |
|
ethernet_phy1: ethernet-phy@4 { |
|
compatible = "ethernet-phy-ieee802.3-c22"; |
|
reg = <4>; |
|
}; |
|
}; |
|
|
|
};
|
|
|