forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
250 lines
12 KiB
250 lines
12 KiB
.. include:: <isonum.txt> |
|
|
|
================================= |
|
Video Mode Selection Support 2.13 |
|
================================= |
|
|
|
:Copyright: |copy| 1995--1999 Martin Mares, <[email protected]> |
|
|
|
Intro |
|
~~~~~ |
|
|
|
This small document describes the "Video Mode Selection" feature which |
|
allows the use of various special video modes supported by the video BIOS. Due |
|
to usage of the BIOS, the selection is limited to boot time (before the |
|
kernel decompression starts) and works only on 80X86 machines that are |
|
booted through BIOS firmware (as opposed to through UEFI, kexec, etc.). |
|
|
|
.. note:: |
|
|
|
Short intro for the impatient: Just use vga=ask for the first time, |
|
enter ``scan`` on the video mode prompt, pick the mode you want to use, |
|
remember its mode ID (the four-digit hexadecimal number) and then |
|
set the vga parameter to this number (converted to decimal first). |
|
|
|
The video mode to be used is selected by a kernel parameter which can be |
|
specified in the kernel Makefile (the SVGA_MODE=... line) or by the "vga=..." |
|
option of LILO (or some other boot loader you use) or by the "xrandr" utility |
|
(present in standard Linux utility packages). You can use the following values |
|
of this parameter:: |
|
|
|
NORMAL_VGA - Standard 80x25 mode available on all display adapters. |
|
|
|
EXTENDED_VGA - Standard 8-pixel font mode: 80x43 on EGA, 80x50 on VGA. |
|
|
|
ASK_VGA - Display a video mode menu upon startup (see below). |
|
|
|
0..35 - Menu item number (when you have used the menu to view the list of |
|
modes available on your adapter, you can specify the menu item you want |
|
to use). 0..9 correspond to "0".."9", 10..35 to "a".."z". Warning: the |
|
mode list displayed may vary as the kernel version changes, because the |
|
modes are listed in a "first detected -- first displayed" manner. It's |
|
better to use absolute mode numbers instead. |
|
|
|
0x.... - Hexadecimal video mode ID (also displayed on the menu, see below |
|
for exact meaning of the ID). Warning: LILO doesn't support |
|
hexadecimal numbers -- you have to convert it to decimal manually. |
|
|
|
Menu |
|
~~~~ |
|
|
|
The ASK_VGA mode causes the kernel to offer a video mode menu upon |
|
bootup. It displays a "Press <RETURN> to see video modes available, <SPACE> |
|
to continue or wait 30 secs" message. If you press <RETURN>, you enter the |
|
menu, if you press <SPACE> or wait 30 seconds, the kernel will boot up in |
|
the standard 80x25 mode. |
|
|
|
The menu looks like:: |
|
|
|
Video adapter: <name-of-detected-video-adapter> |
|
Mode: COLSxROWS: |
|
0 0F00 80x25 |
|
1 0F01 80x50 |
|
2 0F02 80x43 |
|
3 0F03 80x26 |
|
.... |
|
Enter mode number or ``scan``: <flashing-cursor-here> |
|
|
|
<name-of-detected-video-adapter> tells what video adapter did Linux detect |
|
-- it's either a generic adapter name (MDA, CGA, HGC, EGA, VGA, VESA VGA [a VGA |
|
with VESA-compliant BIOS]) or a chipset name (e.g., Trident). Direct detection |
|
of chipsets is turned off by default as it's inherently unreliable due to |
|
absolutely insane PC design. |
|
|
|
"0 0F00 80x25" means that the first menu item (the menu items are numbered |
|
from "0" to "9" and from "a" to "z") is a 80x25 mode with ID=0x0f00 (see the |
|
next section for a description of mode IDs). |
|
|
|
<flashing-cursor-here> encourages you to enter the item number or mode ID |
|
you wish to set and press <RETURN>. If the computer complains something about |
|
"Unknown mode ID", it is trying to tell you that it isn't possible to set such |
|
a mode. It's also possible to press only <RETURN> which leaves the current mode. |
|
|
|
The mode list usually contains a few basic modes and some VESA modes. In |
|
case your chipset has been detected, some chipset-specific modes are shown as |
|
well (some of these might be missing or unusable on your machine as different |
|
BIOSes are often shipped with the same card and the mode numbers depend purely |
|
on the VGA BIOS). |
|
|
|
The modes displayed on the menu are partially sorted: The list starts with |
|
the standard modes (80x25 and 80x50) followed by "special" modes (80x28 and |
|
80x43), local modes (if the local modes feature is enabled), VESA modes and |
|
finally SVGA modes for the auto-detected adapter. |
|
|
|
If you are not happy with the mode list offered (e.g., if you think your card |
|
is able to do more), you can enter "scan" instead of item number / mode ID. The |
|
program will try to ask the BIOS for all possible video mode numbers and test |
|
what happens then. The screen will be probably flashing wildly for some time and |
|
strange noises will be heard from inside the monitor and so on and then, really |
|
all consistent video modes supported by your BIOS will appear (plus maybe some |
|
``ghost modes``). If you are afraid this could damage your monitor, don't use |
|
this function. |
|
|
|
After scanning, the mode ordering is a bit different: the auto-detected SVGA |
|
modes are not listed at all and the modes revealed by ``scan`` are shown before |
|
all VESA modes. |
|
|
|
Mode IDs |
|
~~~~~~~~ |
|
|
|
Because of the complexity of all the video stuff, the video mode IDs |
|
used here are also a bit complex. A video mode ID is a 16-bit number usually |
|
expressed in a hexadecimal notation (starting with "0x"). You can set a mode |
|
by entering its mode directly if you know it even if it isn't shown on the menu. |
|
|
|
The ID numbers can be divided to those regions:: |
|
|
|
0x0000 to 0x00ff - menu item references. 0x0000 is the first item. Don't use |
|
outside the menu as this can change from boot to boot (especially if you |
|
have used the ``scan`` feature). |
|
|
|
0x0100 to 0x017f - standard BIOS modes. The ID is a BIOS video mode number |
|
(as presented to INT 10, function 00) increased by 0x0100. |
|
|
|
0x0200 to 0x08ff - VESA BIOS modes. The ID is a VESA mode ID increased by |
|
0x0100. All VESA modes should be autodetected and shown on the menu. |
|
|
|
0x0900 to 0x09ff - Video7 special modes. Set by calling INT 0x10, AX=0x6f05. |
|
(Usually 940=80x43, 941=132x25, 942=132x44, 943=80x60, 944=100x60, |
|
945=132x28 for the standard Video7 BIOS) |
|
|
|
0x0f00 to 0x0fff - special modes (they are set by various tricks -- usually |
|
by modifying one of the standard modes). Currently available: |
|
0x0f00 standard 80x25, don't reset mode if already set (=FFFF) |
|
0x0f01 standard with 8-point font: 80x43 on EGA, 80x50 on VGA |
|
0x0f02 VGA 80x43 (VGA switched to 350 scanlines with a 8-point font) |
|
0x0f03 VGA 80x28 (standard VGA scans, but 14-point font) |
|
0x0f04 leave current video mode |
|
0x0f05 VGA 80x30 (480 scans, 16-point font) |
|
0x0f06 VGA 80x34 (480 scans, 14-point font) |
|
0x0f07 VGA 80x60 (480 scans, 8-point font) |
|
0x0f08 Graphics hack (see the VIDEO_GFX_HACK paragraph below) |
|
|
|
0x1000 to 0x7fff - modes specified by resolution. The code has a "0xRRCC" |
|
form where RR is a number of rows and CC is a number of columns. |
|
E.g., 0x1950 corresponds to a 80x25 mode, 0x2b84 to 132x43 etc. |
|
This is the only fully portable way to refer to a non-standard mode, |
|
but it relies on the mode being found and displayed on the menu |
|
(remember that mode scanning is not done automatically). |
|
|
|
0xff00 to 0xffff - aliases for backward compatibility: |
|
0xffff equivalent to 0x0f00 (standard 80x25) |
|
0xfffe equivalent to 0x0f01 (EGA 80x43 or VGA 80x50) |
|
|
|
If you add 0x8000 to the mode ID, the program will try to recalculate |
|
vertical display timing according to mode parameters, which can be used to |
|
eliminate some annoying bugs of certain VGA BIOSes (usually those used for |
|
cards with S3 chipsets and old Cirrus Logic BIOSes) -- mainly extra lines at the |
|
end of the display. |
|
|
|
Options |
|
~~~~~~~ |
|
|
|
Build options for arch/x86/boot/* are selected by the kernel kconfig |
|
utility and the kernel .config file. |
|
|
|
VIDEO_GFX_HACK - includes special hack for setting of graphics modes |
|
to be used later by special drivers. |
|
Allows to set _any_ BIOS mode including graphic ones and forcing specific |
|
text screen resolution instead of peeking it from BIOS variables. Don't use |
|
unless you think you know what you're doing. To activate this setup, use |
|
mode number 0x0f08 (see the Mode IDs section above). |
|
|
|
Still doesn't work? |
|
~~~~~~~~~~~~~~~~~~~ |
|
|
|
When the mode detection doesn't work (e.g., the mode list is incorrect or |
|
the machine hangs instead of displaying the menu), try to switch off some of |
|
the configuration options listed under "Options". If it fails, you can still use |
|
your kernel with the video mode set directly via the kernel parameter. |
|
|
|
In either case, please send me a bug report containing what _exactly_ |
|
happens and how do the configuration switches affect the behaviour of the bug. |
|
|
|
If you start Linux from M$-DOS, you might also use some DOS tools for |
|
video mode setting. In this case, you must specify the 0x0f04 mode ("leave |
|
current settings") to Linux, because if you don't and you use any non-standard |
|
mode, Linux will switch to 80x25 automatically. |
|
|
|
If you set some extended mode and there's one or more extra lines on the |
|
bottom of the display containing already scrolled-out text, your VGA BIOS |
|
contains the most common video BIOS bug called "incorrect vertical display |
|
end setting". Adding 0x8000 to the mode ID might fix the problem. Unfortunately, |
|
this must be done manually -- no autodetection mechanisms are available. |
|
|
|
History |
|
~~~~~~~ |
|
|
|
=============== ================================================================ |
|
1.0 (??-Nov-95) First version supporting all adapters supported by the old |
|
setup.S + Cirrus Logic 54XX. Present in some 1.3.4? kernels |
|
and then removed due to instability on some machines. |
|
2.0 (28-Jan-96) Rewritten from scratch. Cirrus Logic 64XX support added, almost |
|
everything is configurable, the VESA support should be much more |
|
stable, explicit mode numbering allowed, "scan" implemented etc. |
|
2.1 (30-Jan-96) VESA modes moved to 0x200-0x3ff. Mode selection by resolution |
|
supported. Few bugs fixed. VESA modes are listed prior to |
|
modes supplied by SVGA autodetection as they are more reliable. |
|
CLGD autodetect works better. Doesn't depend on 80x25 being |
|
active when started. Scanning fixed. 80x43 (any VGA) added. |
|
Code cleaned up. |
|
2.2 (01-Feb-96) EGA 80x43 fixed. VESA extended to 0x200-0x4ff (non-standard 02XX |
|
VESA modes work now). Display end bug workaround supported. |
|
Special modes renumbered to allow adding of the "recalculate" |
|
flag, 0xffff and 0xfffe became aliases instead of real IDs. |
|
Screen contents retained during mode changes. |
|
2.3 (15-Mar-96) Changed to work with 1.3.74 kernel. |
|
2.4 (18-Mar-96) Added patches by Hans Lermen fixing a memory overwrite problem |
|
with some boot loaders. Memory management rewritten to reflect |
|
these changes. Unfortunately, screen contents retaining works |
|
only with some loaders now. |
|
Added a Tseng 132x60 mode. |
|
2.5 (19-Mar-96) Fixed a VESA mode scanning bug introduced in 2.4. |
|
2.6 (25-Mar-96) Some VESA BIOS errors not reported -- it fixes error reports on |
|
several cards with broken VESA code (e.g., ATI VGA). |
|
2.7 (09-Apr-96) - Accepted all VESA modes in range 0x100 to 0x7ff, because some |
|
cards use very strange mode numbers. |
|
- Added Realtek VGA modes (thanks to Gonzalo Tornaria). |
|
- Hardware testing order slightly changed, tests based on ROM |
|
contents done as first. |
|
- Added support for special Video7 mode switching functions |
|
(thanks to Tom Vander Aa). |
|
- Added 480-scanline modes (especially useful for notebooks, |
|
original version written by [email protected], patched by |
|
Jeff Chua, rewritten by me). |
|
- Screen store/restore fixed. |
|
2.8 (14-Apr-96) - Previous release was not compilable without CONFIG_VIDEO_SVGA. |
|
- Better recognition of text modes during mode scan. |
|
2.9 (12-May-96) - Ignored VESA modes 0x80 - 0xff (more VESA BIOS bugs!) |
|
2.10(11-Nov-96) - The whole thing made optional. |
|
- Added the CONFIG_VIDEO_400_HACK switch. |
|
- Added the CONFIG_VIDEO_GFX_HACK switch. |
|
- Code cleanup. |
|
2.11(03-May-97) - Yet another cleanup, now including also the documentation. |
|
- Direct testing of SVGA adapters turned off by default, ``scan`` |
|
offered explicitly on the prompt line. |
|
- Removed the doc section describing adding of new probing |
|
functions as I try to get rid of _all_ hardware probing here. |
|
2.12(25-May-98) Added support for VESA frame buffer graphics. |
|
2.13(14-May-99) Minor documentation fixes. |
|
=============== ================================================================
|
|
|