forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
366 lines
12 KiB
366 lines
12 KiB
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) |
|
%YAML 1.2 |
|
--- |
|
$id: http://devicetree.org/schemas/pinctrl/mediatek,mt7986-pinctrl.yaml# |
|
$schema: http://devicetree.org/meta-schemas/core.yaml# |
|
|
|
title: Mediatek MT7986 Pin Controller Device Tree Bindings |
|
|
|
maintainers: |
|
- Sean Wang <[email protected]> |
|
|
|
description: |+ |
|
The MediaTek's MT7986 Pin controller is used to control SoC pins. |
|
|
|
properties: |
|
compatible: |
|
enum: |
|
- mediatek,mt7986a-pinctrl |
|
- mediatek,mt7986b-pinctrl |
|
|
|
reg: |
|
minItems: 8 |
|
maxItems: 8 |
|
|
|
reg-names: |
|
items: |
|
- const: gpio |
|
- const: iocfg_rt |
|
- const: iocfg_rb |
|
- const: iocfg_lt |
|
- const: iocfg_lb |
|
- const: iocfg_tr |
|
- const: iocfg_tl |
|
- const: eint |
|
|
|
gpio-controller: true |
|
|
|
"#gpio-cells": |
|
const: 2 |
|
description: | |
|
Number of cells in GPIO specifier. Since the generic GPIO |
|
binding is used, the amount of cells must be specified as 2. See the below |
|
mentioned gpio binding representation for description of particular cells. |
|
|
|
gpio-ranges: |
|
minItems: 1 |
|
maxItems: 5 |
|
description: | |
|
GPIO valid number range. |
|
|
|
interrupt-controller: true |
|
|
|
interrupts: |
|
maxItems: 1 |
|
|
|
"#interrupt-cells": |
|
const: 2 |
|
|
|
allOf: |
|
- $ref: "pinctrl.yaml#" |
|
|
|
required: |
|
- compatible |
|
- reg |
|
- reg-names |
|
- gpio-controller |
|
- "#gpio-cells" |
|
|
|
patternProperties: |
|
'-pins$': |
|
type: object |
|
additionalProperties: false |
|
|
|
patternProperties: |
|
'.*mux.*': |
|
type: object |
|
additionalProperties: false |
|
description: | |
|
pinmux configuration nodes. |
|
|
|
The following table shows the effective values of "group", "function" |
|
properties and chip pinout pins |
|
|
|
groups function pins (in pin#) |
|
--------------------------------------------------------------------- |
|
"watchdog" "watchdog" 0 |
|
"wifi_led" "led" 1, 2 |
|
"i2c" "i2c" 3, 4 |
|
"uart1_0" "uart" 7, 8, 9, 10 |
|
"pcie_clk" "pcie" 9 |
|
"pcie_wake" "pcie" 10 |
|
"spi1_0" "spi" 11, 12, 13, 14 |
|
"pwm1_1" "pwm" 20, |
|
"pwm0" "pwm" 21, |
|
"pwm1_0" "pwm" 22, |
|
"snfi" "flash" 23, 24, 25, 26, 27, 28 |
|
"spi1_2" "spi" 29, 30, 31, 32 |
|
"emmc_45" "emmc" 22, 23, 24, 25, 26, 27, 28, 29, 30, |
|
31, 32 |
|
"spi1_1" "spi" 23, 24, 25, 26 |
|
"uart1_2" "uart" 29, 30, 31, 32 |
|
"uart1_1" "uart" 23, 24, 25, 26 |
|
"uart2_0" "uart" 29, 30, 31, 32 |
|
"spi0" "spi" 33, 34, 35, 36 |
|
"spi0_wp_hold" "spi" 37, 38 |
|
"uart1_3_rx_tx" "uart" 35, 36 |
|
"uart1_3_cts_rts" "uart" 37, 38 |
|
"uart2_1" "uart" 33, 34, 35, 36 |
|
"spi1_3" "spi" 33, 34, 35, 36 |
|
"uart0" "uart" 39, 40 |
|
"pcie_pereset" "pcie" 41 |
|
"uart1" "uart" 42, 43, 44, 45 |
|
"uart2" "uart" 46, 47, 48, 49 |
|
"emmc_51" "emmc" 50, 51, 52, 53, 54, 55, 56, 57, 57, |
|
59, 60, 61 |
|
"pcm" "audio" 62, 63, 64, 65 |
|
"i2s" "audio" 62, 63, 64, 65 |
|
"switch_int" "eth" 66 |
|
"mdc_mdio" "eth" 67 |
|
|
|
$ref: "/schemas/pinctrl/pinmux-node.yaml" |
|
properties: |
|
function: |
|
description: | |
|
A string containing the name of the function to mux to the group. |
|
There is no "audio", "pcie" functions on mt7986b, you can only use |
|
those functions on mt7986a. |
|
enum: [audio, emmc, eth, i2c, led, flash, pcie, pwm, spi, uart, |
|
watchdog, wifi] |
|
groups: |
|
description: | |
|
An array of strings. Each string contains the name of a group. |
|
There is no "pcie_pereset", "uart1", "uart2" "emmc_51", "pcm", |
|
and "i2s" groups on mt7986b, you can only use those groups on |
|
mt7986a. |
|
required: |
|
- function |
|
- groups |
|
|
|
allOf: |
|
- if: |
|
properties: |
|
function: |
|
const: audio |
|
then: |
|
properties: |
|
groups: |
|
enum: [pcm, i2s] |
|
- if: |
|
properties: |
|
function: |
|
const: emmc |
|
then: |
|
properties: |
|
groups: |
|
enum: [emmc, emmc_rst] |
|
- if: |
|
properties: |
|
function: |
|
const: eth |
|
then: |
|
properties: |
|
groups: |
|
enum: [switch_int, mdc_mdio] |
|
- if: |
|
properties: |
|
function: |
|
const: i2c |
|
then: |
|
properties: |
|
groups: |
|
enum: [i2c] |
|
- if: |
|
properties: |
|
function: |
|
const: led |
|
then: |
|
properties: |
|
groups: |
|
enum: [wifi_led] |
|
- if: |
|
properties: |
|
function: |
|
const: flash |
|
then: |
|
properties: |
|
groups: |
|
enum: [snfi] |
|
- if: |
|
properties: |
|
function: |
|
const: pcie |
|
then: |
|
properties: |
|
groups: |
|
enum: [pcie_clk, pcie_wake, pcie_pereset] |
|
- if: |
|
properties: |
|
function: |
|
const: pwm |
|
then: |
|
properties: |
|
groups: |
|
enum: [pwm0, pwm1_0, pwm1_1] |
|
- if: |
|
properties: |
|
function: |
|
const: spi |
|
then: |
|
properties: |
|
groups: |
|
enum: [spi0, spi0_wp_hold, spi1_0, spi1_1, spi1_2, spi1_3] |
|
- if: |
|
properties: |
|
function: |
|
const: uart |
|
then: |
|
properties: |
|
groups: |
|
enum: [uart1_0, uart1_1, uart1_2, uart1_3_rx_tx, |
|
uart1_3_cts_rts, uart2_0, uart2_1, uart0, uart1, uart2] |
|
- if: |
|
properties: |
|
function: |
|
const: watchdog |
|
then: |
|
properties: |
|
groups: |
|
enum: [watchdog] |
|
- if: |
|
properties: |
|
function: |
|
const: wifi |
|
then: |
|
properties: |
|
groups: |
|
enum: [wf_2g, wf_5g, wf_dbdc] |
|
'.*conf.*': |
|
type: object |
|
additionalProperties: false |
|
description: | |
|
pinconf configuration nodes. |
|
$ref: "/schemas/pinctrl/pincfg-node.yaml" |
|
|
|
properties: |
|
pins: |
|
description: | |
|
An array of strings. Each string contains the name of a pin. |
|
There is no PIN 41 to PIN 65 above on mt7686b, you can only use |
|
those pins on mt7986a. |
|
enum: [SYS_WATCHDOG, WF2G_LED, WF5G_LED, I2C_SCL, I2C_SDA, GPIO_0, |
|
GPIO_1, GPIO_2, GPIO_3, GPIO_4, GPIO_5, GPIO_6, GPIO_7, |
|
GPIO_8, GPIO_9, GPIO_10, GPIO_11, GPIO_12, GPIO_13, GPIO_14, |
|
GPIO_15, PWM0, PWM1, SPI0_CLK, SPI0_MOSI, SPI0_MISO, SPI0_CS, |
|
SPI0_HOLD, SPI0_WP, SPI1_CLK, SPI1_MOSI, SPI1_MISO, SPI1_CS, |
|
SPI2_CLK, SPI2_MOSI, SPI2_MISO, SPI2_CS, SPI2_HOLD, SPI2_WP, |
|
UART0_RXD, UART0_TXD, PCIE_PERESET_N, UART1_RXD, UART1_TXD, |
|
UART1_CTS, UART1_RTS, UART2_RXD, UART2_TXD, UART2_CTS, |
|
UART2_RTS, EMMC_DATA_0, EMMC_DATA_1, EMMC_DATA_2, |
|
EMMC_DATA_3, EMMC_DATA_4, EMMC_DATA_5, EMMC_DATA_6, |
|
EMMC_DATA_7, EMMC_CMD, EMMC_CK, EMMC_DSL, EMMC_RSTB, PCM_DTX, |
|
PCM_DRX, PCM_CLK, PCM_FS, MT7531_INT, SMI_MDC, SMI_MDIO, |
|
WF0_DIG_RESETB, WF0_CBA_RESETB, WF0_XO_REQ, WF0_TOP_CLK, |
|
WF0_TOP_DATA, WF0_HB1, WF0_HB2, WF0_HB3, WF0_HB4, WF0_HB0, |
|
WF0_HB0_B, WF0_HB5, WF0_HB6, WF0_HB7, WF0_HB8, WF0_HB9, |
|
WF0_HB10, WF1_DIG_RESETB, WF1_CBA_RESETB, WF1_XO_REQ, |
|
WF1_TOP_CLK, WF1_TOP_DATA, WF1_HB1, WF1_HB2, WF1_HB3, |
|
WF1_HB4, WF1_HB0, WF1_HB0_B, WF1_HB5, WF1_HB6, WF1_HB7, |
|
WF1_HB8] |
|
|
|
bias-disable: true |
|
|
|
bias-pull-up: true |
|
|
|
bias-pull-down: true |
|
|
|
input-enable: true |
|
|
|
input-disable: true |
|
|
|
output-enable: true |
|
|
|
output-low: true |
|
|
|
output-high: true |
|
|
|
input-schmitt-enable: true |
|
|
|
input-schmitt-disable: true |
|
|
|
drive-strength: |
|
enum: [2, 4, 6, 8, 10, 12, 14, 16] |
|
|
|
mediatek,pull-up-adv: |
|
description: | |
|
Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3' |
|
Pull up setings for 2 pull resistors, R0 and R1. Valid arguments |
|
are described as below: |
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. |
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. |
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. |
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. |
|
$ref: /schemas/types.yaml#/definitions/uint32 |
|
enum: [0, 1, 2, 3] |
|
|
|
mediatek,pull-down-adv: |
|
description: | |
|
Valid arguments for 'mediatek,pull-up-adv' are '0', '1', '2', '3' |
|
Pull down setings for 2 pull resistors, R0 and R1. Valid arguments |
|
are described as below: |
|
0: (R1, R0) = (0, 0) which means R1 disabled and R0 disabled. |
|
1: (R1, R0) = (0, 1) which means R1 disabled and R0 enabled. |
|
2: (R1, R0) = (1, 0) which means R1 enabled and R0 disabled. |
|
3: (R1, R0) = (1, 1) which means R1 enabled and R0 enabled. |
|
$ref: /schemas/types.yaml#/definitions/uint32 |
|
enum: [0, 1, 2, 3] |
|
|
|
required: |
|
- pins |
|
|
|
additionalProperties: false |
|
|
|
examples: |
|
- | |
|
#include <dt-bindings/interrupt-controller/irq.h> |
|
#include <dt-bindings/interrupt-controller/arm-gic.h> |
|
|
|
soc { |
|
#address-cells = <2>; |
|
#size-cells = <2>; |
|
pio: pinctrl@1001f000 { |
|
compatible = "mediatek,mt7986a-pinctrl"; |
|
reg = <0 0x1001f000 0 0x1000>, |
|
<0 0x11c30000 0 0x1000>, |
|
<0 0x11c40000 0 0x1000>, |
|
<0 0x11e20000 0 0x1000>, |
|
<0 0x11e30000 0 0x1000>, |
|
<0 0x11f00000 0 0x1000>, |
|
<0 0x11f10000 0 0x1000>, |
|
<0 0x1000b000 0 0x1000>; |
|
reg-names = "gpio", "iocfg_rt", "iocfg_rb", "iocfg_lt", |
|
"iocfg_lb", "iocfg_tr", "iocfg_tl", "eint"; |
|
gpio-controller; |
|
#gpio-cells = <2>; |
|
gpio-ranges = <&pio 0 0 100>; |
|
interrupt-controller; |
|
interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH>; |
|
interrupt-parent = <&gic>; |
|
#interrupt-cells = <2>; |
|
|
|
uart1_pins: uart1-pins { |
|
mux { |
|
function = "uart"; |
|
groups = "uart1"; |
|
}; |
|
}; |
|
|
|
uart2_pins: uart2-pins { |
|
mux { |
|
function = "uart"; |
|
groups = "uart2"; |
|
}; |
|
}; |
|
|
|
}; |
|
};
|
|
|