forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
259 lines
7.5 KiB
259 lines
7.5 KiB
// SPDX-License-Identifier: GPL-2.0 |
|
/* |
|
* Emagic EMI 2|6 usb audio interface firmware loader. |
|
* Copyright (C) 2002 |
|
* Tapio Laxström ([email protected]) |
|
* |
|
* emi26.c,v 1.13 2002/03/08 13:10:26 tapio Exp |
|
*/ |
|
#include <linux/kernel.h> |
|
#include <linux/errno.h> |
|
#include <linux/slab.h> |
|
#include <linux/module.h> |
|
#include <linux/usb.h> |
|
#include <linux/delay.h> |
|
#include <linux/firmware.h> |
|
#include <linux/ihex.h> |
|
|
|
#define EMI26_VENDOR_ID 0x086a /* Emagic Soft-und Hardware GmBH */ |
|
#define EMI26_PRODUCT_ID 0x0100 /* EMI 2|6 without firmware */ |
|
#define EMI26B_PRODUCT_ID 0x0102 /* EMI 2|6 without firmware */ |
|
|
|
#define ANCHOR_LOAD_INTERNAL 0xA0 /* Vendor specific request code for Anchor Upload/Download (This one is implemented in the core) */ |
|
#define ANCHOR_LOAD_EXTERNAL 0xA3 /* This command is not implemented in the core. Requires firmware */ |
|
#define ANCHOR_LOAD_FPGA 0xA5 /* This command is not implemented in the core. Requires firmware. Emagic extension */ |
|
#define MAX_INTERNAL_ADDRESS 0x1B3F /* This is the highest internal RAM address for the AN2131Q */ |
|
#define CPUCS_REG 0x7F92 /* EZ-USB Control and Status Register. Bit 0 controls 8051 reset */ |
|
#define INTERNAL_RAM(address) (address <= MAX_INTERNAL_ADDRESS) |
|
|
|
static int emi26_writememory( struct usb_device *dev, int address, |
|
const unsigned char *data, int length, |
|
__u8 bRequest); |
|
static int emi26_set_reset(struct usb_device *dev, unsigned char reset_bit); |
|
static int emi26_load_firmware (struct usb_device *dev); |
|
static int emi26_probe(struct usb_interface *intf, const struct usb_device_id *id); |
|
static void emi26_disconnect(struct usb_interface *intf); |
|
|
|
/* thanks to drivers/usb/serial/keyspan_pda.c code */ |
|
static int emi26_writememory (struct usb_device *dev, int address, |
|
const unsigned char *data, int length, |
|
__u8 request) |
|
{ |
|
int result; |
|
unsigned char *buffer = kmemdup(data, length, GFP_KERNEL); |
|
|
|
if (!buffer) { |
|
dev_err(&dev->dev, "kmalloc(%d) failed.\n", length); |
|
return -ENOMEM; |
|
} |
|
/* Note: usb_control_msg returns negative value on error or length of the |
|
* data that was written! */ |
|
result = usb_control_msg (dev, usb_sndctrlpipe(dev, 0), request, 0x40, address, 0, buffer, length, 300); |
|
kfree (buffer); |
|
return result; |
|
} |
|
|
|
/* thanks to drivers/usb/serial/keyspan_pda.c code */ |
|
static int emi26_set_reset (struct usb_device *dev, unsigned char reset_bit) |
|
{ |
|
int response; |
|
dev_info(&dev->dev, "%s - %d\n", __func__, reset_bit); |
|
/* printk(KERN_DEBUG "%s - %d", __func__, reset_bit); */ |
|
response = emi26_writememory (dev, CPUCS_REG, &reset_bit, 1, 0xa0); |
|
if (response < 0) { |
|
dev_err(&dev->dev, "set_reset (%d) failed\n", reset_bit); |
|
} |
|
return response; |
|
} |
|
|
|
#define FW_LOAD_SIZE 1023 |
|
|
|
static int emi26_load_firmware (struct usb_device *dev) |
|
{ |
|
const struct firmware *loader_fw = NULL; |
|
const struct firmware *bitstream_fw = NULL; |
|
const struct firmware *firmware_fw = NULL; |
|
const struct ihex_binrec *rec; |
|
int err = -ENOMEM; |
|
int i; |
|
__u32 addr; /* Address to write */ |
|
__u8 *buf; |
|
|
|
buf = kmalloc(FW_LOAD_SIZE, GFP_KERNEL); |
|
if (!buf) |
|
goto wraperr; |
|
|
|
err = request_ihex_firmware(&loader_fw, "emi26/loader.fw", &dev->dev); |
|
if (err) |
|
goto nofw; |
|
|
|
err = request_ihex_firmware(&bitstream_fw, "emi26/bitstream.fw", |
|
&dev->dev); |
|
if (err) |
|
goto nofw; |
|
|
|
err = request_ihex_firmware(&firmware_fw, "emi26/firmware.fw", |
|
&dev->dev); |
|
if (err) { |
|
nofw: |
|
dev_err(&dev->dev, "%s - request_firmware() failed\n", |
|
__func__); |
|
goto wraperr; |
|
} |
|
|
|
/* Assert reset (stop the CPU in the EMI) */ |
|
err = emi26_set_reset(dev,1); |
|
if (err < 0) |
|
goto wraperr; |
|
|
|
rec = (const struct ihex_binrec *)loader_fw->data; |
|
/* 1. We need to put the loader for the FPGA into the EZ-USB */ |
|
while (rec) { |
|
err = emi26_writememory(dev, be32_to_cpu(rec->addr), |
|
rec->data, be16_to_cpu(rec->len), |
|
ANCHOR_LOAD_INTERNAL); |
|
if (err < 0) |
|
goto wraperr; |
|
rec = ihex_next_binrec(rec); |
|
} |
|
|
|
/* De-assert reset (let the CPU run) */ |
|
err = emi26_set_reset(dev,0); |
|
if (err < 0) |
|
goto wraperr; |
|
msleep(250); /* let device settle */ |
|
|
|
/* 2. We upload the FPGA firmware into the EMI |
|
* Note: collect up to 1023 (yes!) bytes and send them with |
|
* a single request. This is _much_ faster! */ |
|
rec = (const struct ihex_binrec *)bitstream_fw->data; |
|
do { |
|
i = 0; |
|
addr = be32_to_cpu(rec->addr); |
|
|
|
/* intel hex records are terminated with type 0 element */ |
|
while (rec && (i + be16_to_cpu(rec->len) < FW_LOAD_SIZE)) { |
|
memcpy(buf + i, rec->data, be16_to_cpu(rec->len)); |
|
i += be16_to_cpu(rec->len); |
|
rec = ihex_next_binrec(rec); |
|
} |
|
err = emi26_writememory(dev, addr, buf, i, ANCHOR_LOAD_FPGA); |
|
if (err < 0) |
|
goto wraperr; |
|
} while (rec); |
|
|
|
/* Assert reset (stop the CPU in the EMI) */ |
|
err = emi26_set_reset(dev,1); |
|
if (err < 0) |
|
goto wraperr; |
|
|
|
/* 3. We need to put the loader for the firmware into the EZ-USB (again...) */ |
|
for (rec = (const struct ihex_binrec *)loader_fw->data; |
|
rec; rec = ihex_next_binrec(rec)) { |
|
err = emi26_writememory(dev, be32_to_cpu(rec->addr), |
|
rec->data, be16_to_cpu(rec->len), |
|
ANCHOR_LOAD_INTERNAL); |
|
if (err < 0) |
|
goto wraperr; |
|
} |
|
msleep(250); /* let device settle */ |
|
|
|
/* De-assert reset (let the CPU run) */ |
|
err = emi26_set_reset(dev,0); |
|
if (err < 0) |
|
goto wraperr; |
|
|
|
/* 4. We put the part of the firmware that lies in the external RAM into the EZ-USB */ |
|
|
|
for (rec = (const struct ihex_binrec *)firmware_fw->data; |
|
rec; rec = ihex_next_binrec(rec)) { |
|
if (!INTERNAL_RAM(be32_to_cpu(rec->addr))) { |
|
err = emi26_writememory(dev, be32_to_cpu(rec->addr), |
|
rec->data, be16_to_cpu(rec->len), |
|
ANCHOR_LOAD_EXTERNAL); |
|
if (err < 0) |
|
goto wraperr; |
|
} |
|
} |
|
|
|
/* Assert reset (stop the CPU in the EMI) */ |
|
err = emi26_set_reset(dev,1); |
|
if (err < 0) |
|
goto wraperr; |
|
|
|
for (rec = (const struct ihex_binrec *)firmware_fw->data; |
|
rec; rec = ihex_next_binrec(rec)) { |
|
if (INTERNAL_RAM(be32_to_cpu(rec->addr))) { |
|
err = emi26_writememory(dev, be32_to_cpu(rec->addr), |
|
rec->data, be16_to_cpu(rec->len), |
|
ANCHOR_LOAD_INTERNAL); |
|
if (err < 0) |
|
goto wraperr; |
|
} |
|
} |
|
|
|
/* De-assert reset (let the CPU run) */ |
|
err = emi26_set_reset(dev,0); |
|
if (err < 0) |
|
goto wraperr; |
|
msleep(250); /* let device settle */ |
|
|
|
/* return 1 to fail the driver inialization |
|
* and give real driver change to load */ |
|
err = 1; |
|
|
|
wraperr: |
|
if (err < 0) |
|
dev_err(&dev->dev,"%s - error loading firmware: error = %d\n", |
|
__func__, err); |
|
|
|
release_firmware(loader_fw); |
|
release_firmware(bitstream_fw); |
|
release_firmware(firmware_fw); |
|
|
|
kfree(buf); |
|
return err; |
|
} |
|
|
|
static const struct usb_device_id id_table[] = { |
|
{ USB_DEVICE(EMI26_VENDOR_ID, EMI26_PRODUCT_ID) }, |
|
{ USB_DEVICE(EMI26_VENDOR_ID, EMI26B_PRODUCT_ID) }, |
|
{ } /* Terminating entry */ |
|
}; |
|
|
|
MODULE_DEVICE_TABLE (usb, id_table); |
|
|
|
static int emi26_probe(struct usb_interface *intf, const struct usb_device_id *id) |
|
{ |
|
struct usb_device *dev = interface_to_usbdev(intf); |
|
|
|
dev_info(&intf->dev, "%s start\n", __func__); |
|
|
|
emi26_load_firmware(dev); |
|
|
|
/* do not return the driver context, let real audio driver do that */ |
|
return -EIO; |
|
} |
|
|
|
static void emi26_disconnect(struct usb_interface *intf) |
|
{ |
|
} |
|
|
|
static struct usb_driver emi26_driver = { |
|
.name = "emi26 - firmware loader", |
|
.probe = emi26_probe, |
|
.disconnect = emi26_disconnect, |
|
.id_table = id_table, |
|
}; |
|
|
|
module_usb_driver(emi26_driver); |
|
|
|
MODULE_AUTHOR("Tapio Laxström"); |
|
MODULE_DESCRIPTION("Emagic EMI 2|6 firmware loader."); |
|
MODULE_LICENSE("GPL"); |
|
|
|
MODULE_FIRMWARE("emi26/loader.fw"); |
|
MODULE_FIRMWARE("emi26/bitstream.fw"); |
|
MODULE_FIRMWARE("emi26/firmware.fw"); |
|
/* vi:ai:syntax=c:sw=8:ts=8:tw=80 |
|
*/
|
|
|