forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
86 lines
3.3 KiB
86 lines
3.3 KiB
/* SPDX-License-Identifier: GPL-2.0 */ |
|
#ifndef _PARISC_SUPERIO_H |
|
#define _PARISC_SUPERIO_H |
|
|
|
#define IC_PIC1 0x20 /* PCI I/O address of master 8259 */ |
|
#define IC_PIC2 0xA0 /* PCI I/O address of slave */ |
|
|
|
/* Config Space Offsets to configuration and base address registers */ |
|
#define SIO_CR 0x5A /* Configuration Register */ |
|
#define SIO_ACPIBAR 0x88 /* ACPI BAR */ |
|
#define SIO_FDCBAR 0x90 /* Floppy Disk Controller BAR */ |
|
#define SIO_SP1BAR 0x94 /* Serial 1 BAR */ |
|
#define SIO_SP2BAR 0x98 /* Serial 2 BAR */ |
|
#define SIO_PPBAR 0x9C /* Parallel BAR */ |
|
|
|
#define TRIGGER_1 0x67 /* Edge/level trigger register 1 */ |
|
#define TRIGGER_2 0x68 /* Edge/level trigger register 2 */ |
|
|
|
/* Interrupt Routing Control registers */ |
|
#define CFG_IR_SER 0x69 /* Serial 1 [0:3] and Serial 2 [4:7] */ |
|
#define CFG_IR_PFD 0x6a /* Parallel [0:3] and Floppy [4:7] */ |
|
#define CFG_IR_IDE 0x6b /* IDE1 [0:3] and IDE2 [4:7] */ |
|
#define CFG_IR_INTAB 0x6c /* PCI INTA [0:3] and INT B [4:7] */ |
|
#define CFG_IR_INTCD 0x6d /* PCI INTC [0:3] and INT D [4:7] */ |
|
#define CFG_IR_PS2 0x6e /* PS/2 KBINT [0:3] and Mouse [4:7] */ |
|
#define CFG_IR_FXBUS 0x6f /* FXIRQ[0] [0:3] and FXIRQ[1] [4:7] */ |
|
#define CFG_IR_USB 0x70 /* FXIRQ[2] [0:3] and USB [4:7] */ |
|
#define CFG_IR_ACPI 0x71 /* ACPI SCI [0:3] and reserved [4:7] */ |
|
|
|
#define CFG_IR_LOW CFG_IR_SER /* Lowest interrupt routing reg */ |
|
#define CFG_IR_HIGH CFG_IR_ACPI /* Highest interrupt routing reg */ |
|
|
|
/* 8259 operational control words */ |
|
#define OCW2_EOI 0x20 /* Non-specific EOI */ |
|
#define OCW2_SEOI 0x60 /* Specific EOI */ |
|
#define OCW3_IIR 0x0A /* Read request register */ |
|
#define OCW3_ISR 0x0B /* Read service register */ |
|
#define OCW3_POLL 0x0C /* Poll the PIC for an interrupt vector */ |
|
|
|
/* Interrupt lines. Only PIC1 is used */ |
|
#define USB_IRQ 1 /* USB */ |
|
#define SP1_IRQ 3 /* Serial port 1 */ |
|
#define SP2_IRQ 4 /* Serial port 2 */ |
|
#define PAR_IRQ 5 /* Parallel port */ |
|
#define FDC_IRQ 6 /* Floppy controller */ |
|
#define IDE_IRQ 7 /* IDE (pri+sec) */ |
|
|
|
/* ACPI registers */ |
|
#define USB_REG_CR 0x1f /* USB Regulator Control Register */ |
|
|
|
#define SUPERIO_NIRQS 8 |
|
|
|
struct superio_device { |
|
u32 fdc_base; |
|
u32 sp1_base; |
|
u32 sp2_base; |
|
u32 pp_base; |
|
u32 acpi_base; |
|
int suckyio_irq_enabled; |
|
struct pci_dev *lio_pdev; /* pci device for legacy IO (fn 1) */ |
|
struct pci_dev *usb_pdev; /* pci device for USB (fn 2) */ |
|
}; |
|
|
|
/* |
|
* Does NS make a 87415 based plug in PCI card? If so, because of this |
|
* macro we currently don't support it being plugged into a machine |
|
* that contains a SuperIO chip AND has CONFIG_SUPERIO enabled. |
|
* |
|
* This could be fixed by checking to see if function 1 exists, and |
|
* if it is SuperIO Legacy IO; but really now, is this combination |
|
* going to EVER happen? |
|
*/ |
|
|
|
#define SUPERIO_IDE_FN 0 /* Function number of IDE controller */ |
|
#define SUPERIO_LIO_FN 1 /* Function number of Legacy IO controller */ |
|
#define SUPERIO_USB_FN 2 /* Function number of USB controller */ |
|
|
|
#define is_superio_device(x) \ |
|
(((x)->vendor == PCI_VENDOR_ID_NS) && \ |
|
( ((x)->device == PCI_DEVICE_ID_NS_87415) \ |
|
|| ((x)->device == PCI_DEVICE_ID_NS_87560_LIO) \ |
|
|| ((x)->device == PCI_DEVICE_ID_NS_87560_USB) ) ) |
|
|
|
extern int superio_fixup_irq(struct pci_dev *pcidev); /* called by iosapic */ |
|
|
|
#endif /* _PARISC_SUPERIO_H */
|
|
|