forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
117 lines
4.5 KiB
117 lines
4.5 KiB
/* |
|
* Summit Microelectronics SMB347 Battery Charger Driver |
|
* |
|
* Copyright (C) 2011, Intel Corporation |
|
* |
|
* Authors: Bruce E. Robertson <[email protected]> |
|
* Mika Westerberg <[email protected]> |
|
* |
|
* This program is free software; you can redistribute it and/or modify |
|
* it under the terms of the GNU General Public License version 2 as |
|
* published by the Free Software Foundation. |
|
*/ |
|
|
|
#ifndef SMB347_CHARGER_H |
|
#define SMB347_CHARGER_H |
|
|
|
#include <linux/types.h> |
|
#include <linux/power_supply.h> |
|
|
|
enum { |
|
/* use the default compensation method */ |
|
SMB347_SOFT_TEMP_COMPENSATE_DEFAULT = -1, |
|
|
|
SMB347_SOFT_TEMP_COMPENSATE_NONE, |
|
SMB347_SOFT_TEMP_COMPENSATE_CURRENT, |
|
SMB347_SOFT_TEMP_COMPENSATE_VOLTAGE, |
|
}; |
|
|
|
/* Use default factory programmed value for hard/soft temperature limit */ |
|
#define SMB347_TEMP_USE_DEFAULT -273 |
|
|
|
/* |
|
* Charging enable can be controlled by software (via i2c) by |
|
* smb347-charger driver or by EN pin (active low/high). |
|
*/ |
|
enum smb347_chg_enable { |
|
SMB347_CHG_ENABLE_SW, |
|
SMB347_CHG_ENABLE_PIN_ACTIVE_LOW, |
|
SMB347_CHG_ENABLE_PIN_ACTIVE_HIGH, |
|
}; |
|
|
|
/** |
|
* struct smb347_charger_platform_data - platform data for SMB347 charger |
|
* @battery_info: Information about the battery |
|
* @max_charge_current: maximum current (in uA) the battery can be charged |
|
* @max_charge_voltage: maximum voltage (in uV) the battery can be charged |
|
* @pre_charge_current: current (in uA) to use in pre-charging phase |
|
* @termination_current: current (in uA) used to determine when the |
|
* charging cycle terminates |
|
* @pre_to_fast_voltage: voltage (in uV) treshold used for transitioning to |
|
* pre-charge to fast charge mode |
|
* @mains_current_limit: maximum input current drawn from AC/DC input (in uA) |
|
* @usb_hc_current_limit: maximum input high current (in uA) drawn from USB |
|
* input |
|
* @chip_temp_threshold: die temperature where device starts limiting charge |
|
* current [%100 - %130] (in degree C) |
|
* @soft_cold_temp_limit: soft cold temperature limit [%0 - %15] (in degree C), |
|
* granularity is 5 deg C. |
|
* @soft_hot_temp_limit: soft hot temperature limit [%40 - %55] (in degree C), |
|
* granularity is 5 deg C. |
|
* @hard_cold_temp_limit: hard cold temperature limit [%-5 - %10] (in degree C), |
|
* granularity is 5 deg C. |
|
* @hard_hot_temp_limit: hard hot temperature limit [%50 - %65] (in degree C), |
|
* granularity is 5 deg C. |
|
* @suspend_on_hard_temp_limit: suspend charging when hard limit is hit |
|
* @soft_temp_limit_compensation: compensation method when soft temperature |
|
* limit is hit |
|
* @charge_current_compensation: current (in uA) for charging compensation |
|
* current when temperature hits soft limits |
|
* @use_mains: AC/DC input can be used |
|
* @use_usb: USB input can be used |
|
* @use_usb_otg: USB OTG output can be used (not implemented yet) |
|
* @irq_gpio: GPIO number used for interrupts (%-1 if not used) |
|
* @enable_control: how charging enable/disable is controlled |
|
* (driver/pin controls) |
|
* |
|
* @use_main, @use_usb, and @use_usb_otg are means to enable/disable |
|
* hardware support for these. This is useful when we want to have for |
|
* example OTG charging controlled via OTG transceiver driver and not by |
|
* the SMB347 hardware. |
|
* |
|
* Hard and soft temperature limit values are given as described in the |
|
* device data sheet and assuming NTC beta value is %3750. Even if this is |
|
* not the case, these values should be used. They can be mapped to the |
|
* corresponding NTC beta values with the help of table %2 in the data |
|
* sheet. So for example if NTC beta is %3375 and we want to program hard |
|
* hot limit to be %53 deg C, @hard_hot_temp_limit should be set to %50. |
|
* |
|
* If zero value is given in any of the current and voltage values, the |
|
* factory programmed default will be used. For soft/hard temperature |
|
* values, pass in %SMB347_TEMP_USE_DEFAULT instead. |
|
*/ |
|
struct smb347_charger_platform_data { |
|
struct power_supply_info battery_info; |
|
unsigned int max_charge_current; |
|
unsigned int max_charge_voltage; |
|
unsigned int pre_charge_current; |
|
unsigned int termination_current; |
|
unsigned int pre_to_fast_voltage; |
|
unsigned int mains_current_limit; |
|
unsigned int usb_hc_current_limit; |
|
unsigned int chip_temp_threshold; |
|
int soft_cold_temp_limit; |
|
int soft_hot_temp_limit; |
|
int hard_cold_temp_limit; |
|
int hard_hot_temp_limit; |
|
bool suspend_on_hard_temp_limit; |
|
unsigned int soft_temp_limit_compensation; |
|
unsigned int charge_current_compensation; |
|
bool use_mains; |
|
bool use_usb; |
|
bool use_usb_otg; |
|
int irq_gpio; |
|
enum smb347_chg_enable enable_control; |
|
}; |
|
|
|
#endif /* SMB347_CHARGER_H */
|
|
|