forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
1469 lines
44 KiB
1469 lines
44 KiB
// SPDX-License-Identifier: GPL-2.0-or-later |
|
/* |
|
* sonix sn9c102 (bayer) library |
|
* |
|
* Copyright (C) 2009-2011 Jean-François Moine <http://moinejf.free.fr> |
|
* Copyright (C) 2003 2004 Michel Xhaard [email protected] |
|
* Add Pas106 Stefano Mozzi (C) 2004 |
|
*/ |
|
|
|
/* Some documentation on known sonixb registers: |
|
|
|
Reg Use |
|
sn9c101 / sn9c102: |
|
0x10 high nibble red gain low nibble blue gain |
|
0x11 low nibble green gain |
|
sn9c103: |
|
0x05 red gain 0-127 |
|
0x06 blue gain 0-127 |
|
0x07 green gain 0-127 |
|
all: |
|
0x08-0x0f i2c / 3wire registers |
|
0x12 hstart |
|
0x13 vstart |
|
0x15 hsize (hsize = register-value * 16) |
|
0x16 vsize (vsize = register-value * 16) |
|
0x17 bit 0 toggle compression quality (according to sn9c102 driver) |
|
0x18 bit 7 enables compression, bit 4-5 set image down scaling: |
|
00 scale 1, 01 scale 1/2, 10, scale 1/4 |
|
0x19 high-nibble is sensor clock divider, changes exposure on sensors which |
|
use a clock generated by the bridge. Some sensors have their own clock. |
|
0x1c auto_exposure area (for avg_lum) startx (startx = register-value * 32) |
|
0x1d auto_exposure area (for avg_lum) starty (starty = register-value * 32) |
|
0x1e auto_exposure area (for avg_lum) stopx (hsize = (0x1e - 0x1c) * 32) |
|
0x1f auto_exposure area (for avg_lum) stopy (vsize = (0x1f - 0x1d) * 32) |
|
*/ |
|
|
|
#define MODULE_NAME "sonixb" |
|
|
|
#include <linux/input.h> |
|
#include "gspca.h" |
|
|
|
MODULE_AUTHOR("Jean-François Moine <http://moinejf.free.fr>"); |
|
MODULE_DESCRIPTION("GSPCA/SN9C102 USB Camera Driver"); |
|
MODULE_LICENSE("GPL"); |
|
|
|
/* specific webcam descriptor */ |
|
struct sd { |
|
struct gspca_dev gspca_dev; /* !! must be the first item */ |
|
|
|
struct v4l2_ctrl *brightness; |
|
struct v4l2_ctrl *plfreq; |
|
|
|
atomic_t avg_lum; |
|
int prev_avg_lum; |
|
int exposure_knee; |
|
int header_read; |
|
u8 header[12]; /* Header without sof marker */ |
|
|
|
unsigned char autogain_ignore_frames; |
|
unsigned char frames_to_drop; |
|
|
|
__u8 bridge; /* Type of bridge */ |
|
#define BRIDGE_101 0 |
|
#define BRIDGE_102 0 /* We make no difference between 101 and 102 */ |
|
#define BRIDGE_103 1 |
|
|
|
__u8 sensor; /* Type of image sensor chip */ |
|
#define SENSOR_HV7131D 0 |
|
#define SENSOR_HV7131R 1 |
|
#define SENSOR_OV6650 2 |
|
#define SENSOR_OV7630 3 |
|
#define SENSOR_PAS106 4 |
|
#define SENSOR_PAS202 5 |
|
#define SENSOR_TAS5110C 6 |
|
#define SENSOR_TAS5110D 7 |
|
#define SENSOR_TAS5130CXX 8 |
|
__u8 reg11; |
|
}; |
|
|
|
typedef const __u8 sensor_init_t[8]; |
|
|
|
struct sensor_data { |
|
const __u8 *bridge_init; |
|
sensor_init_t *sensor_init; |
|
int sensor_init_size; |
|
int flags; |
|
__u8 sensor_addr; |
|
}; |
|
|
|
/* sensor_data flags */ |
|
#define F_SIF 0x01 /* sif or vga */ |
|
|
|
/* priv field of struct v4l2_pix_format flags (do not use low nibble!) */ |
|
#define MODE_RAW 0x10 /* raw bayer mode */ |
|
#define MODE_REDUCED_SIF 0x20 /* vga mode (320x240 / 160x120) on sif cam */ |
|
|
|
#define COMP 0xc7 /* 0x87 //0x07 */ |
|
#define COMP1 0xc9 /* 0x89 //0x09 */ |
|
|
|
#define MCK_INIT 0x63 |
|
#define MCK_INIT1 0x20 /*fixme: Bayer - 0x50 for JPEG ??*/ |
|
|
|
#define SYS_CLK 0x04 |
|
|
|
#define SENS(bridge, sensor, _flags, _sensor_addr) \ |
|
{ \ |
|
.bridge_init = bridge, \ |
|
.sensor_init = sensor, \ |
|
.sensor_init_size = sizeof(sensor), \ |
|
.flags = _flags, .sensor_addr = _sensor_addr \ |
|
} |
|
|
|
/* We calculate the autogain at the end of the transfer of a frame, at this |
|
moment a frame with the old settings is being captured and transmitted. So |
|
if we adjust the gain or exposure we must ignore at least the next frame for |
|
the new settings to come into effect before doing any other adjustments. */ |
|
#define AUTOGAIN_IGNORE_FRAMES 1 |
|
|
|
static const struct v4l2_pix_format vga_mode[] = { |
|
{160, 120, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, |
|
.bytesperline = 160, |
|
.sizeimage = 160 * 120, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 2 | MODE_RAW}, |
|
{160, 120, V4L2_PIX_FMT_SN9C10X, V4L2_FIELD_NONE, |
|
.bytesperline = 160, |
|
.sizeimage = 160 * 120 * 5 / 4, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 2}, |
|
{320, 240, V4L2_PIX_FMT_SN9C10X, V4L2_FIELD_NONE, |
|
.bytesperline = 320, |
|
.sizeimage = 320 * 240 * 5 / 4, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 1}, |
|
{640, 480, V4L2_PIX_FMT_SN9C10X, V4L2_FIELD_NONE, |
|
.bytesperline = 640, |
|
.sizeimage = 640 * 480 * 5 / 4, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 0}, |
|
}; |
|
static const struct v4l2_pix_format sif_mode[] = { |
|
{160, 120, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, |
|
.bytesperline = 160, |
|
.sizeimage = 160 * 120, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 1 | MODE_RAW | MODE_REDUCED_SIF}, |
|
{160, 120, V4L2_PIX_FMT_SN9C10X, V4L2_FIELD_NONE, |
|
.bytesperline = 160, |
|
.sizeimage = 160 * 120 * 5 / 4, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 1 | MODE_REDUCED_SIF}, |
|
{176, 144, V4L2_PIX_FMT_SBGGR8, V4L2_FIELD_NONE, |
|
.bytesperline = 176, |
|
.sizeimage = 176 * 144, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 1 | MODE_RAW}, |
|
{176, 144, V4L2_PIX_FMT_SN9C10X, V4L2_FIELD_NONE, |
|
.bytesperline = 176, |
|
.sizeimage = 176 * 144 * 5 / 4, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 1}, |
|
{320, 240, V4L2_PIX_FMT_SN9C10X, V4L2_FIELD_NONE, |
|
.bytesperline = 320, |
|
.sizeimage = 320 * 240 * 5 / 4, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 0 | MODE_REDUCED_SIF}, |
|
{352, 288, V4L2_PIX_FMT_SN9C10X, V4L2_FIELD_NONE, |
|
.bytesperline = 352, |
|
.sizeimage = 352 * 288 * 5 / 4, |
|
.colorspace = V4L2_COLORSPACE_SRGB, |
|
.priv = 0}, |
|
}; |
|
|
|
static const __u8 initHv7131d[] = { |
|
0x04, 0x03, 0x00, 0x04, 0x00, 0x00, 0x00, 0x80, 0x11, 0x00, 0x00, 0x00, |
|
0x00, 0x00, |
|
0x00, 0x00, 0x00, 0x02, 0x02, 0x00, |
|
0x28, 0x1e, 0x60, 0x8e, 0x42, |
|
}; |
|
static const __u8 hv7131d_sensor_init[][8] = { |
|
{0xa0, 0x11, 0x01, 0x04, 0x00, 0x00, 0x00, 0x17}, |
|
{0xa0, 0x11, 0x02, 0x00, 0x00, 0x00, 0x00, 0x17}, |
|
{0xa0, 0x11, 0x28, 0x00, 0x00, 0x00, 0x00, 0x17}, |
|
{0xa0, 0x11, 0x30, 0x30, 0x00, 0x00, 0x00, 0x17}, /* reset level */ |
|
{0xa0, 0x11, 0x34, 0x02, 0x00, 0x00, 0x00, 0x17}, /* pixel bias volt */ |
|
}; |
|
|
|
static const __u8 initHv7131r[] = { |
|
0x46, 0x77, 0x00, 0x04, 0x00, 0x00, 0x00, 0x80, 0x11, 0x00, 0x00, 0x00, |
|
0x00, 0x00, |
|
0x00, 0x00, 0x00, 0x02, 0x01, 0x00, |
|
0x28, 0x1e, 0x60, 0x8a, 0x20, |
|
}; |
|
static const __u8 hv7131r_sensor_init[][8] = { |
|
{0xc0, 0x11, 0x31, 0x38, 0x2a, 0x2e, 0x00, 0x10}, |
|
{0xa0, 0x11, 0x01, 0x08, 0x2a, 0x2e, 0x00, 0x10}, |
|
{0xb0, 0x11, 0x20, 0x00, 0xd0, 0x2e, 0x00, 0x10}, |
|
{0xc0, 0x11, 0x25, 0x03, 0x0e, 0x28, 0x00, 0x16}, |
|
{0xa0, 0x11, 0x30, 0x10, 0x0e, 0x28, 0x00, 0x15}, |
|
}; |
|
static const __u8 initOv6650[] = { |
|
0x44, 0x44, 0x00, 0x00, 0x00, 0x00, 0x00, 0x80, |
|
0x60, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, |
|
0x00, 0x01, 0x01, 0x0a, 0x16, 0x12, 0x68, 0x8b, |
|
0x10, |
|
}; |
|
static const __u8 ov6650_sensor_init[][8] = { |
|
/* Bright, contrast, etc are set through SCBB interface. |
|
* AVCAP on win2 do not send any data on this controls. */ |
|
/* Anyway, some registers appears to alter bright and constrat */ |
|
|
|
/* Reset sensor */ |
|
{0xa0, 0x60, 0x12, 0x80, 0x00, 0x00, 0x00, 0x10}, |
|
/* Set clock register 0x11 low nibble is clock divider */ |
|
{0xd0, 0x60, 0x11, 0xc0, 0x1b, 0x18, 0xc1, 0x10}, |
|
/* Next some unknown stuff */ |
|
{0xb0, 0x60, 0x15, 0x00, 0x02, 0x18, 0xc1, 0x10}, |
|
/* {0xa0, 0x60, 0x1b, 0x01, 0x02, 0x18, 0xc1, 0x10}, |
|
* THIS SET GREEN SCREEN |
|
* (pixels could be innverted in decode kind of "brg", |
|
* but blue wont be there. Avoid this data ... */ |
|
{0xd0, 0x60, 0x26, 0x01, 0x14, 0xd8, 0xa4, 0x10}, /* format out? */ |
|
{0xd0, 0x60, 0x26, 0x01, 0x14, 0xd8, 0xa4, 0x10}, |
|
{0xa0, 0x60, 0x30, 0x3d, 0x0a, 0xd8, 0xa4, 0x10}, |
|
/* Enable rgb brightness control */ |
|
{0xa0, 0x60, 0x61, 0x08, 0x00, 0x00, 0x00, 0x10}, |
|
/* HDG: Note windows uses the line below, which sets both register 0x60 |
|
and 0x61 I believe these registers of the ov6650 are identical as |
|
those of the ov7630, because if this is true the windows settings |
|
add a bit additional red gain and a lot additional blue gain, which |
|
matches my findings that the windows settings make blue much too |
|
blue and red a little too red. |
|
{0xb0, 0x60, 0x60, 0x66, 0x68, 0xd8, 0xa4, 0x10}, */ |
|
/* Some more unknown stuff */ |
|
{0xa0, 0x60, 0x68, 0x04, 0x68, 0xd8, 0xa4, 0x10}, |
|
{0xd0, 0x60, 0x17, 0x24, 0xd6, 0x04, 0x94, 0x10}, /* Clipreg */ |
|
}; |
|
|
|
static const __u8 initOv7630[] = { |
|
0x04, 0x44, 0x00, 0x00, 0x00, 0x00, 0x00, 0x80, /* r01 .. r08 */ |
|
0x21, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* r09 .. r10 */ |
|
0x00, 0x01, 0x01, 0x0a, /* r11 .. r14 */ |
|
0x28, 0x1e, /* H & V sizes r15 .. r16 */ |
|
0x68, 0x8f, MCK_INIT1, /* r17 .. r19 */ |
|
}; |
|
static const __u8 ov7630_sensor_init[][8] = { |
|
{0xa0, 0x21, 0x12, 0x80, 0x00, 0x00, 0x00, 0x10}, |
|
{0xb0, 0x21, 0x01, 0x77, 0x3a, 0x00, 0x00, 0x10}, |
|
/* {0xd0, 0x21, 0x12, 0x7c, 0x01, 0x80, 0x34, 0x10}, jfm */ |
|
{0xd0, 0x21, 0x12, 0x5c, 0x00, 0x80, 0x34, 0x10}, /* jfm */ |
|
{0xa0, 0x21, 0x1b, 0x04, 0x00, 0x80, 0x34, 0x10}, |
|
{0xa0, 0x21, 0x20, 0x44, 0x00, 0x80, 0x34, 0x10}, |
|
{0xa0, 0x21, 0x23, 0xee, 0x00, 0x80, 0x34, 0x10}, |
|
{0xd0, 0x21, 0x26, 0xa0, 0x9a, 0xa0, 0x30, 0x10}, |
|
{0xb0, 0x21, 0x2a, 0x80, 0x00, 0xa0, 0x30, 0x10}, |
|
{0xb0, 0x21, 0x2f, 0x3d, 0x24, 0xa0, 0x30, 0x10}, |
|
{0xa0, 0x21, 0x32, 0x86, 0x24, 0xa0, 0x30, 0x10}, |
|
{0xb0, 0x21, 0x60, 0xa9, 0x4a, 0xa0, 0x30, 0x10}, |
|
/* {0xb0, 0x21, 0x60, 0xa9, 0x42, 0xa0, 0x30, 0x10}, * jfm */ |
|
{0xa0, 0x21, 0x65, 0x00, 0x42, 0xa0, 0x30, 0x10}, |
|
{0xa0, 0x21, 0x69, 0x38, 0x42, 0xa0, 0x30, 0x10}, |
|
{0xc0, 0x21, 0x6f, 0x88, 0x0b, 0x00, 0x30, 0x10}, |
|
{0xc0, 0x21, 0x74, 0x21, 0x8e, 0x00, 0x30, 0x10}, |
|
{0xa0, 0x21, 0x7d, 0xf7, 0x8e, 0x00, 0x30, 0x10}, |
|
{0xd0, 0x21, 0x17, 0x1c, 0xbd, 0x06, 0xf6, 0x10}, |
|
}; |
|
|
|
static const __u8 initPas106[] = { |
|
0x04, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, 0x81, 0x40, 0x00, 0x00, 0x00, |
|
0x00, 0x00, |
|
0x00, 0x00, 0x00, 0x04, 0x01, 0x00, |
|
0x16, 0x12, 0x24, COMP1, MCK_INIT1, |
|
}; |
|
/* compression 0x86 mckinit1 0x2b */ |
|
|
|
/* "Known" PAS106B registers: |
|
0x02 clock divider |
|
0x03 Variable framerate bits 4-11 |
|
0x04 Var framerate bits 0-3, one must leave the 4 msb's at 0 !! |
|
The variable framerate control must never be set lower then 300, |
|
which sets the framerate at 90 / reg02, otherwise vsync is lost. |
|
0x05 Shutter Time Line Offset, this can be used as an exposure control: |
|
0 = use full frame time, 255 = no exposure at all |
|
Note this may never be larger then "var-framerate control" / 2 - 2. |
|
When var-framerate control is < 514, no exposure is reached at the max |
|
allowed value for the framerate control value, rather then at 255. |
|
0x06 Shutter Time Pixel Offset, like reg05 this influences exposure, but |
|
only a very little bit, leave at 0xcd |
|
0x07 offset sign bit (bit0 1 > negative offset) |
|
0x08 offset |
|
0x09 Blue Gain |
|
0x0a Green1 Gain |
|
0x0b Green2 Gain |
|
0x0c Red Gain |
|
0x0e Global gain |
|
0x13 Write 1 to commit settings to sensor |
|
*/ |
|
|
|
static const __u8 pas106_sensor_init[][8] = { |
|
/* Pixel Clock Divider 6 */ |
|
{ 0xa1, 0x40, 0x02, 0x04, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Frame Time MSB (also seen as 0x12) */ |
|
{ 0xa1, 0x40, 0x03, 0x13, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Frame Time LSB (also seen as 0x05) */ |
|
{ 0xa1, 0x40, 0x04, 0x06, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Shutter Time Line Offset (also seen as 0x6d) */ |
|
{ 0xa1, 0x40, 0x05, 0x65, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Shutter Time Pixel Offset (also seen as 0xb1) */ |
|
{ 0xa1, 0x40, 0x06, 0xcd, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Black Level Subtract Sign (also seen 0x00) */ |
|
{ 0xa1, 0x40, 0x07, 0xc1, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Black Level Subtract Level (also seen 0x01) */ |
|
{ 0xa1, 0x40, 0x08, 0x06, 0x00, 0x00, 0x00, 0x14 }, |
|
{ 0xa1, 0x40, 0x08, 0x06, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Color Gain B Pixel 5 a */ |
|
{ 0xa1, 0x40, 0x09, 0x05, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Color Gain G1 Pixel 1 5 */ |
|
{ 0xa1, 0x40, 0x0a, 0x04, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Color Gain G2 Pixel 1 0 5 */ |
|
{ 0xa1, 0x40, 0x0b, 0x04, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Color Gain R Pixel 3 1 */ |
|
{ 0xa1, 0x40, 0x0c, 0x05, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Color GainH Pixel */ |
|
{ 0xa1, 0x40, 0x0d, 0x00, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Global Gain */ |
|
{ 0xa1, 0x40, 0x0e, 0x0e, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Contrast */ |
|
{ 0xa1, 0x40, 0x0f, 0x00, 0x00, 0x00, 0x00, 0x14 }, |
|
/* H&V synchro polarity */ |
|
{ 0xa1, 0x40, 0x10, 0x06, 0x00, 0x00, 0x00, 0x14 }, |
|
/* ?default */ |
|
{ 0xa1, 0x40, 0x11, 0x06, 0x00, 0x00, 0x00, 0x14 }, |
|
/* DAC scale */ |
|
{ 0xa1, 0x40, 0x12, 0x06, 0x00, 0x00, 0x00, 0x14 }, |
|
/* ?default */ |
|
{ 0xa1, 0x40, 0x14, 0x02, 0x00, 0x00, 0x00, 0x14 }, |
|
/* Validate Settings */ |
|
{ 0xa1, 0x40, 0x13, 0x01, 0x00, 0x00, 0x00, 0x14 }, |
|
}; |
|
|
|
static const __u8 initPas202[] = { |
|
0x44, 0x44, 0x21, 0x30, 0x00, 0x00, 0x00, 0x80, 0x40, 0x00, 0x00, 0x00, |
|
0x00, 0x00, |
|
0x00, 0x00, 0x00, 0x06, 0x03, 0x0a, |
|
0x28, 0x1e, 0x20, 0x89, 0x20, |
|
}; |
|
|
|
/* "Known" PAS202BCB registers: |
|
0x02 clock divider |
|
0x04 Variable framerate bits 6-11 (*) |
|
0x05 Var framerate bits 0-5, one must leave the 2 msb's at 0 !! |
|
0x07 Blue Gain |
|
0x08 Green Gain |
|
0x09 Red Gain |
|
0x0b offset sign bit (bit0 1 > negative offset) |
|
0x0c offset |
|
0x0e Unknown image is slightly brighter when bit 0 is 0, if reg0f is 0 too, |
|
leave at 1 otherwise we get a jump in our exposure control |
|
0x0f Exposure 0-255, 0 = use full frame time, 255 = no exposure at all |
|
0x10 Master gain 0 - 31 |
|
0x11 write 1 to apply changes |
|
(*) The variable framerate control must never be set lower then 500 |
|
which sets the framerate at 30 / reg02, otherwise vsync is lost. |
|
*/ |
|
static const __u8 pas202_sensor_init[][8] = { |
|
/* Set the clock divider to 4 -> 30 / 4 = 7.5 fps, we would like |
|
to set it lower, but for some reason the bridge starts missing |
|
vsync's then */ |
|
{0xa0, 0x40, 0x02, 0x04, 0x00, 0x00, 0x00, 0x10}, |
|
{0xd0, 0x40, 0x04, 0x07, 0x34, 0x00, 0x09, 0x10}, |
|
{0xd0, 0x40, 0x08, 0x01, 0x00, 0x00, 0x01, 0x10}, |
|
{0xd0, 0x40, 0x0c, 0x00, 0x0c, 0x01, 0x32, 0x10}, |
|
{0xd0, 0x40, 0x10, 0x00, 0x01, 0x00, 0x63, 0x10}, |
|
{0xa0, 0x40, 0x15, 0x70, 0x01, 0x00, 0x63, 0x10}, |
|
{0xa0, 0x40, 0x18, 0x00, 0x01, 0x00, 0x63, 0x10}, |
|
{0xa0, 0x40, 0x11, 0x01, 0x01, 0x00, 0x63, 0x10}, |
|
{0xa0, 0x40, 0x03, 0x56, 0x01, 0x00, 0x63, 0x10}, |
|
{0xa0, 0x40, 0x11, 0x01, 0x01, 0x00, 0x63, 0x10}, |
|
}; |
|
|
|
static const __u8 initTas5110c[] = { |
|
0x44, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, 0x20, 0x11, 0x00, 0x00, 0x00, |
|
0x00, 0x00, |
|
0x00, 0x00, 0x00, 0x45, 0x09, 0x0a, |
|
0x16, 0x12, 0x60, 0x86, 0x2b, |
|
}; |
|
/* Same as above, except a different hstart */ |
|
static const __u8 initTas5110d[] = { |
|
0x44, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, 0x20, 0x11, 0x00, 0x00, 0x00, |
|
0x00, 0x00, |
|
0x00, 0x00, 0x00, 0x41, 0x09, 0x0a, |
|
0x16, 0x12, 0x60, 0x86, 0x2b, |
|
}; |
|
/* tas5110c is 3 wire, tas5110d is 2 wire (regular i2c) */ |
|
static const __u8 tas5110c_sensor_init[][8] = { |
|
{0x30, 0x11, 0x00, 0x00, 0x0c, 0x00, 0x00, 0x10}, |
|
{0x30, 0x11, 0x02, 0x20, 0xa9, 0x00, 0x00, 0x10}, |
|
}; |
|
/* Known TAS5110D registers |
|
* reg02: gain, bit order reversed!! 0 == max gain, 255 == min gain |
|
* reg03: bit3: vflip, bit4: ~hflip, bit7: ~gainboost (~ == inverted) |
|
* Note: writing reg03 seems to only work when written together with 02 |
|
*/ |
|
static const __u8 tas5110d_sensor_init[][8] = { |
|
{0xa0, 0x61, 0x9a, 0xca, 0x00, 0x00, 0x00, 0x17}, /* reset */ |
|
}; |
|
|
|
static const __u8 initTas5130[] = { |
|
0x04, 0x03, 0x00, 0x00, 0x00, 0x00, 0x00, 0x20, 0x11, 0x00, 0x00, 0x00, |
|
0x00, 0x00, |
|
0x00, 0x00, 0x00, 0x68, 0x0c, 0x0a, |
|
0x28, 0x1e, 0x60, COMP, MCK_INIT, |
|
}; |
|
static const __u8 tas5130_sensor_init[][8] = { |
|
/* {0x30, 0x11, 0x00, 0x40, 0x47, 0x00, 0x00, 0x10}, |
|
* shutter 0x47 short exposure? */ |
|
{0x30, 0x11, 0x00, 0x40, 0x01, 0x00, 0x00, 0x10}, |
|
/* shutter 0x01 long exposure */ |
|
{0x30, 0x11, 0x02, 0x20, 0x70, 0x00, 0x00, 0x10}, |
|
}; |
|
|
|
static const struct sensor_data sensor_data[] = { |
|
SENS(initHv7131d, hv7131d_sensor_init, 0, 0), |
|
SENS(initHv7131r, hv7131r_sensor_init, 0, 0), |
|
SENS(initOv6650, ov6650_sensor_init, F_SIF, 0x60), |
|
SENS(initOv7630, ov7630_sensor_init, 0, 0x21), |
|
SENS(initPas106, pas106_sensor_init, F_SIF, 0), |
|
SENS(initPas202, pas202_sensor_init, 0, 0), |
|
SENS(initTas5110c, tas5110c_sensor_init, F_SIF, 0), |
|
SENS(initTas5110d, tas5110d_sensor_init, F_SIF, 0), |
|
SENS(initTas5130, tas5130_sensor_init, 0, 0), |
|
}; |
|
|
|
/* get one byte in gspca_dev->usb_buf */ |
|
static void reg_r(struct gspca_dev *gspca_dev, |
|
__u16 value) |
|
{ |
|
int res; |
|
|
|
if (gspca_dev->usb_err < 0) |
|
return; |
|
|
|
res = usb_control_msg(gspca_dev->dev, |
|
usb_rcvctrlpipe(gspca_dev->dev, 0), |
|
0, /* request */ |
|
USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_INTERFACE, |
|
value, |
|
0, /* index */ |
|
gspca_dev->usb_buf, 1, |
|
500); |
|
|
|
if (res < 0) { |
|
dev_err(gspca_dev->v4l2_dev.dev, |
|
"Error reading register %02x: %d\n", value, res); |
|
gspca_dev->usb_err = res; |
|
/* |
|
* Make sure the result is zeroed to avoid uninitialized |
|
* values. |
|
*/ |
|
gspca_dev->usb_buf[0] = 0; |
|
} |
|
} |
|
|
|
static void reg_w(struct gspca_dev *gspca_dev, |
|
__u16 value, |
|
const __u8 *buffer, |
|
int len) |
|
{ |
|
int res; |
|
|
|
if (gspca_dev->usb_err < 0) |
|
return; |
|
|
|
memcpy(gspca_dev->usb_buf, buffer, len); |
|
res = usb_control_msg(gspca_dev->dev, |
|
usb_sndctrlpipe(gspca_dev->dev, 0), |
|
0x08, /* request */ |
|
USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_INTERFACE, |
|
value, |
|
0, /* index */ |
|
gspca_dev->usb_buf, len, |
|
500); |
|
|
|
if (res < 0) { |
|
dev_err(gspca_dev->v4l2_dev.dev, |
|
"Error writing register %02x: %d\n", value, res); |
|
gspca_dev->usb_err = res; |
|
} |
|
} |
|
|
|
static void i2c_w(struct gspca_dev *gspca_dev, const u8 *buf) |
|
{ |
|
int retry = 60; |
|
|
|
if (gspca_dev->usb_err < 0) |
|
return; |
|
|
|
/* is i2c ready */ |
|
reg_w(gspca_dev, 0x08, buf, 8); |
|
while (retry--) { |
|
if (gspca_dev->usb_err < 0) |
|
return; |
|
msleep(1); |
|
reg_r(gspca_dev, 0x08); |
|
if (gspca_dev->usb_buf[0] & 0x04) { |
|
if (gspca_dev->usb_buf[0] & 0x08) { |
|
dev_err(gspca_dev->v4l2_dev.dev, |
|
"i2c error writing %8ph\n", buf); |
|
gspca_dev->usb_err = -EIO; |
|
} |
|
return; |
|
} |
|
} |
|
|
|
dev_err(gspca_dev->v4l2_dev.dev, "i2c write timeout\n"); |
|
gspca_dev->usb_err = -EIO; |
|
} |
|
|
|
static void i2c_w_vector(struct gspca_dev *gspca_dev, |
|
const __u8 buffer[][8], int len) |
|
{ |
|
for (;;) { |
|
if (gspca_dev->usb_err < 0) |
|
return; |
|
i2c_w(gspca_dev, *buffer); |
|
len -= 8; |
|
if (len <= 0) |
|
break; |
|
buffer++; |
|
} |
|
} |
|
|
|
static void setbrightness(struct gspca_dev *gspca_dev) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
|
|
switch (sd->sensor) { |
|
case SENSOR_OV6650: |
|
case SENSOR_OV7630: { |
|
__u8 i2cOV[] = |
|
{0xa0, 0x00, 0x06, 0x00, 0x00, 0x00, 0x00, 0x10}; |
|
|
|
/* change reg 0x06 */ |
|
i2cOV[1] = sensor_data[sd->sensor].sensor_addr; |
|
i2cOV[3] = sd->brightness->val; |
|
i2c_w(gspca_dev, i2cOV); |
|
break; |
|
} |
|
case SENSOR_PAS106: |
|
case SENSOR_PAS202: { |
|
__u8 i2cpbright[] = |
|
{0xb0, 0x40, 0x0b, 0x00, 0x00, 0x00, 0x00, 0x16}; |
|
__u8 i2cpdoit[] = |
|
{0xa0, 0x40, 0x11, 0x01, 0x00, 0x00, 0x00, 0x16}; |
|
|
|
/* PAS106 uses reg 7 and 8 instead of b and c */ |
|
if (sd->sensor == SENSOR_PAS106) { |
|
i2cpbright[2] = 7; |
|
i2cpdoit[2] = 0x13; |
|
} |
|
|
|
if (sd->brightness->val < 127) { |
|
/* change reg 0x0b, signreg */ |
|
i2cpbright[3] = 0x01; |
|
/* set reg 0x0c, offset */ |
|
i2cpbright[4] = 127 - sd->brightness->val; |
|
} else |
|
i2cpbright[4] = sd->brightness->val - 127; |
|
|
|
i2c_w(gspca_dev, i2cpbright); |
|
i2c_w(gspca_dev, i2cpdoit); |
|
break; |
|
} |
|
default: |
|
break; |
|
} |
|
} |
|
|
|
static void setgain(struct gspca_dev *gspca_dev) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
u8 gain = gspca_dev->gain->val; |
|
|
|
switch (sd->sensor) { |
|
case SENSOR_HV7131D: { |
|
__u8 i2c[] = |
|
{0xc0, 0x11, 0x31, 0x00, 0x00, 0x00, 0x00, 0x17}; |
|
|
|
i2c[3] = 0x3f - gain; |
|
i2c[4] = 0x3f - gain; |
|
i2c[5] = 0x3f - gain; |
|
|
|
i2c_w(gspca_dev, i2c); |
|
break; |
|
} |
|
case SENSOR_TAS5110C: |
|
case SENSOR_TAS5130CXX: { |
|
__u8 i2c[] = |
|
{0x30, 0x11, 0x02, 0x20, 0x70, 0x00, 0x00, 0x10}; |
|
|
|
i2c[4] = 255 - gain; |
|
i2c_w(gspca_dev, i2c); |
|
break; |
|
} |
|
case SENSOR_TAS5110D: { |
|
__u8 i2c[] = { |
|
0xb0, 0x61, 0x02, 0x00, 0x10, 0x00, 0x00, 0x17 }; |
|
gain = 255 - gain; |
|
/* The bits in the register are the wrong way around!! */ |
|
i2c[3] |= (gain & 0x80) >> 7; |
|
i2c[3] |= (gain & 0x40) >> 5; |
|
i2c[3] |= (gain & 0x20) >> 3; |
|
i2c[3] |= (gain & 0x10) >> 1; |
|
i2c[3] |= (gain & 0x08) << 1; |
|
i2c[3] |= (gain & 0x04) << 3; |
|
i2c[3] |= (gain & 0x02) << 5; |
|
i2c[3] |= (gain & 0x01) << 7; |
|
i2c_w(gspca_dev, i2c); |
|
break; |
|
} |
|
case SENSOR_OV6650: |
|
case SENSOR_OV7630: { |
|
__u8 i2c[] = {0xa0, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10}; |
|
|
|
/* |
|
* The ov7630's gain is weird, at 32 the gain drops to the |
|
* same level as at 16, so skip 32-47 (of the 0-63 scale). |
|
*/ |
|
if (sd->sensor == SENSOR_OV7630 && gain >= 32) |
|
gain += 16; |
|
|
|
i2c[1] = sensor_data[sd->sensor].sensor_addr; |
|
i2c[3] = gain; |
|
i2c_w(gspca_dev, i2c); |
|
break; |
|
} |
|
case SENSOR_PAS106: |
|
case SENSOR_PAS202: { |
|
__u8 i2cpgain[] = |
|
{0xa0, 0x40, 0x10, 0x00, 0x00, 0x00, 0x00, 0x15}; |
|
__u8 i2cpcolorgain[] = |
|
{0xc0, 0x40, 0x07, 0x00, 0x00, 0x00, 0x00, 0x15}; |
|
__u8 i2cpdoit[] = |
|
{0xa0, 0x40, 0x11, 0x01, 0x00, 0x00, 0x00, 0x16}; |
|
|
|
/* PAS106 uses different regs (and has split green gains) */ |
|
if (sd->sensor == SENSOR_PAS106) { |
|
i2cpgain[2] = 0x0e; |
|
i2cpcolorgain[0] = 0xd0; |
|
i2cpcolorgain[2] = 0x09; |
|
i2cpdoit[2] = 0x13; |
|
} |
|
|
|
i2cpgain[3] = gain; |
|
i2cpcolorgain[3] = gain >> 1; |
|
i2cpcolorgain[4] = gain >> 1; |
|
i2cpcolorgain[5] = gain >> 1; |
|
i2cpcolorgain[6] = gain >> 1; |
|
|
|
i2c_w(gspca_dev, i2cpgain); |
|
i2c_w(gspca_dev, i2cpcolorgain); |
|
i2c_w(gspca_dev, i2cpdoit); |
|
break; |
|
} |
|
default: |
|
if (sd->bridge == BRIDGE_103) { |
|
u8 buf[3] = { gain, gain, gain }; /* R, G, B */ |
|
reg_w(gspca_dev, 0x05, buf, 3); |
|
} else { |
|
u8 buf[2]; |
|
buf[0] = gain << 4 | gain; /* Red and blue */ |
|
buf[1] = gain; /* Green */ |
|
reg_w(gspca_dev, 0x10, buf, 2); |
|
} |
|
} |
|
} |
|
|
|
static void setexposure(struct gspca_dev *gspca_dev) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
|
|
switch (sd->sensor) { |
|
case SENSOR_HV7131D: { |
|
/* Note the datasheet wrongly says line mode exposure uses reg |
|
0x26 and 0x27, testing has shown 0x25 + 0x26 */ |
|
__u8 i2c[] = {0xc0, 0x11, 0x25, 0x00, 0x00, 0x00, 0x00, 0x17}; |
|
u16 reg = gspca_dev->exposure->val; |
|
|
|
i2c[3] = reg >> 8; |
|
i2c[4] = reg & 0xff; |
|
i2c_w(gspca_dev, i2c); |
|
break; |
|
} |
|
case SENSOR_TAS5110C: |
|
case SENSOR_TAS5110D: { |
|
/* register 19's high nibble contains the sn9c10x clock divider |
|
The high nibble configures the no fps according to the |
|
formula: 60 / high_nibble. With a maximum of 30 fps */ |
|
u8 reg = gspca_dev->exposure->val; |
|
|
|
reg = (reg << 4) | 0x0b; |
|
reg_w(gspca_dev, 0x19, ®, 1); |
|
break; |
|
} |
|
case SENSOR_OV6650: |
|
case SENSOR_OV7630: { |
|
/* The ov6650 / ov7630 have 2 registers which both influence |
|
exposure, register 11, whose low nibble sets the nr off fps |
|
according to: fps = 30 / (low_nibble + 1) |
|
|
|
The fps configures the maximum exposure setting, but it is |
|
possible to use less exposure then what the fps maximum |
|
allows by setting register 10. register 10 configures the |
|
actual exposure as quotient of the full exposure, with 0 |
|
being no exposure at all (not very useful) and reg10_max |
|
being max exposure possible at that framerate. |
|
|
|
The code maps our 0 - 510 ms exposure ctrl to these 2 |
|
registers, trying to keep fps as high as possible. |
|
*/ |
|
__u8 i2c[] = {0xb0, 0x00, 0x10, 0x00, 0x00, 0x00, 0x00, 0x10}; |
|
int reg10, reg11, reg10_max; |
|
|
|
/* ov6645 datasheet says reg10_max is 9a, but that uses |
|
tline * 2 * reg10 as formula for calculating texpo, the |
|
ov6650 probably uses the same formula as the 7730 which uses |
|
tline * 4 * reg10, which explains why the reg10max we've |
|
found experimentally for the ov6650 is exactly half that of |
|
the ov6645. The ov7630 datasheet says the max is 0x41. */ |
|
if (sd->sensor == SENSOR_OV6650) { |
|
reg10_max = 0x4d; |
|
i2c[4] = 0xc0; /* OV6650 needs non default vsync pol */ |
|
} else |
|
reg10_max = 0x41; |
|
|
|
reg11 = (15 * gspca_dev->exposure->val + 999) / 1000; |
|
if (reg11 < 1) |
|
reg11 = 1; |
|
else if (reg11 > 16) |
|
reg11 = 16; |
|
|
|
/* In 640x480, if the reg11 has less than 4, the image is |
|
unstable (the bridge goes into a higher compression mode |
|
which we have not reverse engineered yet). */ |
|
if (gspca_dev->pixfmt.width == 640 && reg11 < 4) |
|
reg11 = 4; |
|
|
|
/* frame exposure time in ms = 1000 * reg11 / 30 -> |
|
reg10 = (gspca_dev->exposure->val / 2) * reg10_max |
|
/ (1000 * reg11 / 30) */ |
|
reg10 = (gspca_dev->exposure->val * 15 * reg10_max) |
|
/ (1000 * reg11); |
|
|
|
/* Don't allow this to get below 10 when using autogain, the |
|
steps become very large (relatively) when below 10 causing |
|
the image to oscillate from much too dark, to much too bright |
|
and back again. */ |
|
if (gspca_dev->autogain->val && reg10 < 10) |
|
reg10 = 10; |
|
else if (reg10 > reg10_max) |
|
reg10 = reg10_max; |
|
|
|
/* Write reg 10 and reg11 low nibble */ |
|
i2c[1] = sensor_data[sd->sensor].sensor_addr; |
|
i2c[3] = reg10; |
|
i2c[4] |= reg11 - 1; |
|
|
|
/* If register 11 didn't change, don't change it */ |
|
if (sd->reg11 == reg11) |
|
i2c[0] = 0xa0; |
|
|
|
i2c_w(gspca_dev, i2c); |
|
if (gspca_dev->usb_err == 0) |
|
sd->reg11 = reg11; |
|
break; |
|
} |
|
case SENSOR_PAS202: { |
|
__u8 i2cpframerate[] = |
|
{0xb0, 0x40, 0x04, 0x00, 0x00, 0x00, 0x00, 0x16}; |
|
__u8 i2cpexpo[] = |
|
{0xa0, 0x40, 0x0f, 0x00, 0x00, 0x00, 0x00, 0x16}; |
|
const __u8 i2cpdoit[] = |
|
{0xa0, 0x40, 0x11, 0x01, 0x00, 0x00, 0x00, 0x16}; |
|
int framerate_ctrl; |
|
|
|
/* The exposure knee for the autogain algorithm is 200 |
|
(100 ms / 10 fps on other sensors), for values below this |
|
use the control for setting the partial frame expose time, |
|
above that use variable framerate. This way we run at max |
|
framerate ([email protected] fps, 320x240@10fps) until the knee |
|
is reached. Using the variable framerate control above 200 |
|
is better then playing around with both clockdiv + partial |
|
frame exposure times (like we are doing with the ov chips), |
|
as that sometimes leads to jumps in the exposure control, |
|
which are bad for auto exposure. */ |
|
if (gspca_dev->exposure->val < 200) { |
|
i2cpexpo[3] = 255 - (gspca_dev->exposure->val * 255) |
|
/ 200; |
|
framerate_ctrl = 500; |
|
} else { |
|
/* The PAS202's exposure control goes from 0 - 4095, |
|
but anything below 500 causes vsync issues, so scale |
|
our 200-1023 to 500-4095 */ |
|
framerate_ctrl = (gspca_dev->exposure->val - 200) |
|
* 1000 / 229 + 500; |
|
} |
|
|
|
i2cpframerate[3] = framerate_ctrl >> 6; |
|
i2cpframerate[4] = framerate_ctrl & 0x3f; |
|
i2c_w(gspca_dev, i2cpframerate); |
|
i2c_w(gspca_dev, i2cpexpo); |
|
i2c_w(gspca_dev, i2cpdoit); |
|
break; |
|
} |
|
case SENSOR_PAS106: { |
|
__u8 i2cpframerate[] = |
|
{0xb1, 0x40, 0x03, 0x00, 0x00, 0x00, 0x00, 0x14}; |
|
__u8 i2cpexpo[] = |
|
{0xa1, 0x40, 0x05, 0x00, 0x00, 0x00, 0x00, 0x14}; |
|
const __u8 i2cpdoit[] = |
|
{0xa1, 0x40, 0x13, 0x01, 0x00, 0x00, 0x00, 0x14}; |
|
int framerate_ctrl; |
|
|
|
/* For values below 150 use partial frame exposure, above |
|
that use framerate ctrl */ |
|
if (gspca_dev->exposure->val < 150) { |
|
i2cpexpo[3] = 150 - gspca_dev->exposure->val; |
|
framerate_ctrl = 300; |
|
} else { |
|
/* The PAS106's exposure control goes from 0 - 4095, |
|
but anything below 300 causes vsync issues, so scale |
|
our 150-1023 to 300-4095 */ |
|
framerate_ctrl = (gspca_dev->exposure->val - 150) |
|
* 1000 / 230 + 300; |
|
} |
|
|
|
i2cpframerate[3] = framerate_ctrl >> 4; |
|
i2cpframerate[4] = framerate_ctrl & 0x0f; |
|
i2c_w(gspca_dev, i2cpframerate); |
|
i2c_w(gspca_dev, i2cpexpo); |
|
i2c_w(gspca_dev, i2cpdoit); |
|
break; |
|
} |
|
default: |
|
break; |
|
} |
|
} |
|
|
|
static void setfreq(struct gspca_dev *gspca_dev) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
|
|
if (sd->sensor == SENSOR_OV6650 || sd->sensor == SENSOR_OV7630) { |
|
/* Framerate adjust register for artificial light 50 hz flicker |
|
compensation, for the ov6650 this is identical to ov6630 |
|
0x2b register, see ov6630 datasheet. |
|
0x4f / 0x8a -> (30 fps -> 25 fps), 0x00 -> no adjustment */ |
|
__u8 i2c[] = {0xa0, 0x00, 0x2b, 0x00, 0x00, 0x00, 0x00, 0x10}; |
|
switch (sd->plfreq->val) { |
|
default: |
|
/* case 0: * no filter*/ |
|
/* case 2: * 60 hz */ |
|
i2c[3] = 0; |
|
break; |
|
case 1: /* 50 hz */ |
|
i2c[3] = (sd->sensor == SENSOR_OV6650) |
|
? 0x4f : 0x8a; |
|
break; |
|
} |
|
i2c[1] = sensor_data[sd->sensor].sensor_addr; |
|
i2c_w(gspca_dev, i2c); |
|
} |
|
} |
|
|
|
static void do_autogain(struct gspca_dev *gspca_dev) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
int deadzone, desired_avg_lum, avg_lum; |
|
|
|
avg_lum = atomic_read(&sd->avg_lum); |
|
if (avg_lum == -1) |
|
return; |
|
|
|
if (sd->autogain_ignore_frames > 0) { |
|
sd->autogain_ignore_frames--; |
|
return; |
|
} |
|
|
|
/* SIF / VGA sensors have a different autoexposure area and thus |
|
different avg_lum values for the same picture brightness */ |
|
if (sensor_data[sd->sensor].flags & F_SIF) { |
|
deadzone = 500; |
|
/* SIF sensors tend to overexpose, so keep this small */ |
|
desired_avg_lum = 5000; |
|
} else { |
|
deadzone = 1500; |
|
desired_avg_lum = 13000; |
|
} |
|
|
|
if (sd->brightness) |
|
desired_avg_lum = sd->brightness->val * desired_avg_lum / 127; |
|
|
|
if (gspca_dev->exposure->maximum < 500) { |
|
if (gspca_coarse_grained_expo_autogain(gspca_dev, avg_lum, |
|
desired_avg_lum, deadzone)) |
|
sd->autogain_ignore_frames = AUTOGAIN_IGNORE_FRAMES; |
|
} else { |
|
int gain_knee = (s32)gspca_dev->gain->maximum * 9 / 10; |
|
if (gspca_expo_autogain(gspca_dev, avg_lum, desired_avg_lum, |
|
deadzone, gain_knee, sd->exposure_knee)) |
|
sd->autogain_ignore_frames = AUTOGAIN_IGNORE_FRAMES; |
|
} |
|
} |
|
|
|
/* this function is called at probe time */ |
|
static int sd_config(struct gspca_dev *gspca_dev, |
|
const struct usb_device_id *id) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
struct cam *cam; |
|
|
|
reg_r(gspca_dev, 0x00); |
|
if (gspca_dev->usb_buf[0] != 0x10) |
|
return -ENODEV; |
|
|
|
/* copy the webcam info from the device id */ |
|
sd->sensor = id->driver_info >> 8; |
|
sd->bridge = id->driver_info & 0xff; |
|
|
|
cam = &gspca_dev->cam; |
|
if (!(sensor_data[sd->sensor].flags & F_SIF)) { |
|
cam->cam_mode = vga_mode; |
|
cam->nmodes = ARRAY_SIZE(vga_mode); |
|
} else { |
|
cam->cam_mode = sif_mode; |
|
cam->nmodes = ARRAY_SIZE(sif_mode); |
|
} |
|
cam->npkt = 36; /* 36 packets per ISOC message */ |
|
|
|
return 0; |
|
} |
|
|
|
/* this function is called at probe and resume time */ |
|
static int sd_init(struct gspca_dev *gspca_dev) |
|
{ |
|
const __u8 stop = 0x09; /* Disable stream turn of LED */ |
|
|
|
reg_w(gspca_dev, 0x01, &stop, 1); |
|
|
|
return gspca_dev->usb_err; |
|
} |
|
|
|
static int sd_s_ctrl(struct v4l2_ctrl *ctrl) |
|
{ |
|
struct gspca_dev *gspca_dev = |
|
container_of(ctrl->handler, struct gspca_dev, ctrl_handler); |
|
struct sd *sd = (struct sd *)gspca_dev; |
|
|
|
gspca_dev->usb_err = 0; |
|
|
|
if (ctrl->id == V4L2_CID_AUTOGAIN && ctrl->is_new && ctrl->val) { |
|
/* when switching to autogain set defaults to make sure |
|
we are on a valid point of the autogain gain / |
|
exposure knee graph, and give this change time to |
|
take effect before doing autogain. */ |
|
gspca_dev->gain->val = gspca_dev->gain->default_value; |
|
gspca_dev->exposure->val = gspca_dev->exposure->default_value; |
|
sd->autogain_ignore_frames = AUTOGAIN_IGNORE_FRAMES; |
|
} |
|
|
|
if (!gspca_dev->streaming) |
|
return 0; |
|
|
|
switch (ctrl->id) { |
|
case V4L2_CID_BRIGHTNESS: |
|
setbrightness(gspca_dev); |
|
break; |
|
case V4L2_CID_AUTOGAIN: |
|
if (gspca_dev->exposure->is_new || (ctrl->is_new && ctrl->val)) |
|
setexposure(gspca_dev); |
|
if (gspca_dev->gain->is_new || (ctrl->is_new && ctrl->val)) |
|
setgain(gspca_dev); |
|
break; |
|
case V4L2_CID_POWER_LINE_FREQUENCY: |
|
setfreq(gspca_dev); |
|
break; |
|
default: |
|
return -EINVAL; |
|
} |
|
return gspca_dev->usb_err; |
|
} |
|
|
|
static const struct v4l2_ctrl_ops sd_ctrl_ops = { |
|
.s_ctrl = sd_s_ctrl, |
|
}; |
|
|
|
/* this function is called at probe time */ |
|
static int sd_init_controls(struct gspca_dev *gspca_dev) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
struct v4l2_ctrl_handler *hdl = &gspca_dev->ctrl_handler; |
|
|
|
gspca_dev->vdev.ctrl_handler = hdl; |
|
v4l2_ctrl_handler_init(hdl, 5); |
|
|
|
if (sd->sensor == SENSOR_OV6650 || sd->sensor == SENSOR_OV7630 || |
|
sd->sensor == SENSOR_PAS106 || sd->sensor == SENSOR_PAS202) |
|
sd->brightness = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_BRIGHTNESS, 0, 255, 1, 127); |
|
|
|
/* Gain range is sensor dependent */ |
|
switch (sd->sensor) { |
|
case SENSOR_OV6650: |
|
case SENSOR_PAS106: |
|
case SENSOR_PAS202: |
|
gspca_dev->gain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_GAIN, 0, 31, 1, 15); |
|
break; |
|
case SENSOR_OV7630: |
|
gspca_dev->gain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_GAIN, 0, 47, 1, 31); |
|
break; |
|
case SENSOR_HV7131D: |
|
gspca_dev->gain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_GAIN, 0, 63, 1, 31); |
|
break; |
|
case SENSOR_TAS5110C: |
|
case SENSOR_TAS5110D: |
|
case SENSOR_TAS5130CXX: |
|
gspca_dev->gain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_GAIN, 0, 255, 1, 127); |
|
break; |
|
default: |
|
if (sd->bridge == BRIDGE_103) { |
|
gspca_dev->gain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_GAIN, 0, 127, 1, 63); |
|
} else { |
|
gspca_dev->gain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_GAIN, 0, 15, 1, 7); |
|
} |
|
} |
|
|
|
/* Exposure range is sensor dependent, and not all have exposure */ |
|
switch (sd->sensor) { |
|
case SENSOR_HV7131D: |
|
gspca_dev->exposure = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_EXPOSURE, 0, 8191, 1, 482); |
|
sd->exposure_knee = 964; |
|
break; |
|
case SENSOR_OV6650: |
|
case SENSOR_OV7630: |
|
case SENSOR_PAS106: |
|
case SENSOR_PAS202: |
|
gspca_dev->exposure = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_EXPOSURE, 0, 1023, 1, 66); |
|
sd->exposure_knee = 200; |
|
break; |
|
case SENSOR_TAS5110C: |
|
case SENSOR_TAS5110D: |
|
gspca_dev->exposure = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_EXPOSURE, 2, 15, 1, 2); |
|
break; |
|
} |
|
|
|
if (gspca_dev->exposure) { |
|
gspca_dev->autogain = v4l2_ctrl_new_std(hdl, &sd_ctrl_ops, |
|
V4L2_CID_AUTOGAIN, 0, 1, 1, 1); |
|
} |
|
|
|
if (sd->sensor == SENSOR_OV6650 || sd->sensor == SENSOR_OV7630) |
|
sd->plfreq = v4l2_ctrl_new_std_menu(hdl, &sd_ctrl_ops, |
|
V4L2_CID_POWER_LINE_FREQUENCY, |
|
V4L2_CID_POWER_LINE_FREQUENCY_60HZ, 0, |
|
V4L2_CID_POWER_LINE_FREQUENCY_DISABLED); |
|
|
|
if (hdl->error) { |
|
pr_err("Could not initialize controls\n"); |
|
return hdl->error; |
|
} |
|
|
|
if (gspca_dev->autogain) |
|
v4l2_ctrl_auto_cluster(3, &gspca_dev->autogain, 0, false); |
|
|
|
return 0; |
|
} |
|
|
|
/* -- start the camera -- */ |
|
static int sd_start(struct gspca_dev *gspca_dev) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
struct cam *cam = &gspca_dev->cam; |
|
int i, mode; |
|
__u8 regs[0x31]; |
|
|
|
mode = cam->cam_mode[gspca_dev->curr_mode].priv & 0x07; |
|
/* Copy registers 0x01 - 0x19 from the template */ |
|
memcpy(®s[0x01], sensor_data[sd->sensor].bridge_init, 0x19); |
|
/* Set the mode */ |
|
regs[0x18] |= mode << 4; |
|
|
|
/* Set bridge gain to 1.0 */ |
|
if (sd->bridge == BRIDGE_103) { |
|
regs[0x05] = 0x20; /* Red */ |
|
regs[0x06] = 0x20; /* Green */ |
|
regs[0x07] = 0x20; /* Blue */ |
|
} else { |
|
regs[0x10] = 0x00; /* Red and blue */ |
|
regs[0x11] = 0x00; /* Green */ |
|
} |
|
|
|
/* Setup pixel numbers and auto exposure window */ |
|
if (sensor_data[sd->sensor].flags & F_SIF) { |
|
regs[0x1a] = 0x14; /* HO_SIZE 640, makes no sense */ |
|
regs[0x1b] = 0x0a; /* VO_SIZE 320, makes no sense */ |
|
regs[0x1c] = 0x02; /* AE H-start 64 */ |
|
regs[0x1d] = 0x02; /* AE V-start 64 */ |
|
regs[0x1e] = 0x09; /* AE H-end 288 */ |
|
regs[0x1f] = 0x07; /* AE V-end 224 */ |
|
} else { |
|
regs[0x1a] = 0x1d; /* HO_SIZE 960, makes no sense */ |
|
regs[0x1b] = 0x10; /* VO_SIZE 512, makes no sense */ |
|
regs[0x1c] = 0x05; /* AE H-start 160 */ |
|
regs[0x1d] = 0x03; /* AE V-start 96 */ |
|
regs[0x1e] = 0x0f; /* AE H-end 480 */ |
|
regs[0x1f] = 0x0c; /* AE V-end 384 */ |
|
} |
|
|
|
/* Setup the gamma table (only used with the sn9c103 bridge) */ |
|
for (i = 0; i < 16; i++) |
|
regs[0x20 + i] = i * 16; |
|
regs[0x20 + i] = 255; |
|
|
|
/* Special cases where some regs depend on mode or bridge */ |
|
switch (sd->sensor) { |
|
case SENSOR_TAS5130CXX: |
|
/* FIXME / TESTME |
|
probably not mode specific at all most likely the upper |
|
nibble of 0x19 is exposure (clock divider) just as with |
|
the tas5110, we need someone to test this. */ |
|
regs[0x19] = mode ? 0x23 : 0x43; |
|
break; |
|
case SENSOR_OV7630: |
|
/* FIXME / TESTME for some reason with the 101/102 bridge the |
|
clock is set to 12 Mhz (reg1 == 0x04), rather then 24. |
|
Also the hstart needs to go from 1 to 2 when using a 103, |
|
which is likely related. This does not seem right. */ |
|
if (sd->bridge == BRIDGE_103) { |
|
regs[0x01] = 0x44; /* Select 24 Mhz clock */ |
|
regs[0x12] = 0x02; /* Set hstart to 2 */ |
|
} |
|
break; |
|
case SENSOR_PAS202: |
|
/* For some unknown reason we need to increase hstart by 1 on |
|
the sn9c103, otherwise we get wrong colors (bayer shift). */ |
|
if (sd->bridge == BRIDGE_103) |
|
regs[0x12] += 1; |
|
break; |
|
} |
|
/* Disable compression when the raw bayer format has been selected */ |
|
if (cam->cam_mode[gspca_dev->curr_mode].priv & MODE_RAW) |
|
regs[0x18] &= ~0x80; |
|
|
|
/* Vga mode emulation on SIF sensor? */ |
|
if (cam->cam_mode[gspca_dev->curr_mode].priv & MODE_REDUCED_SIF) { |
|
regs[0x12] += 16; /* hstart adjust */ |
|
regs[0x13] += 24; /* vstart adjust */ |
|
regs[0x15] = 320 / 16; /* hsize */ |
|
regs[0x16] = 240 / 16; /* vsize */ |
|
} |
|
|
|
/* reg 0x01 bit 2 video transfert on */ |
|
reg_w(gspca_dev, 0x01, ®s[0x01], 1); |
|
/* reg 0x17 SensorClk enable inv Clk 0x60 */ |
|
reg_w(gspca_dev, 0x17, ®s[0x17], 1); |
|
/* Set the registers from the template */ |
|
reg_w(gspca_dev, 0x01, ®s[0x01], |
|
(sd->bridge == BRIDGE_103) ? 0x30 : 0x1f); |
|
|
|
/* Init the sensor */ |
|
i2c_w_vector(gspca_dev, sensor_data[sd->sensor].sensor_init, |
|
sensor_data[sd->sensor].sensor_init_size); |
|
|
|
/* Mode / bridge specific sensor setup */ |
|
switch (sd->sensor) { |
|
case SENSOR_PAS202: { |
|
const __u8 i2cpclockdiv[] = |
|
{0xa0, 0x40, 0x02, 0x03, 0x00, 0x00, 0x00, 0x10}; |
|
/* clockdiv from 4 to 3 (7.5 -> 10 fps) when in low res mode */ |
|
if (mode) |
|
i2c_w(gspca_dev, i2cpclockdiv); |
|
break; |
|
} |
|
case SENSOR_OV7630: |
|
/* FIXME / TESTME We should be able to handle this identical |
|
for the 101/102 and the 103 case */ |
|
if (sd->bridge == BRIDGE_103) { |
|
const __u8 i2c[] = { 0xa0, 0x21, 0x13, |
|
0x80, 0x00, 0x00, 0x00, 0x10 }; |
|
i2c_w(gspca_dev, i2c); |
|
} |
|
break; |
|
} |
|
/* H_size V_size 0x28, 0x1e -> 640x480. 0x16, 0x12 -> 352x288 */ |
|
reg_w(gspca_dev, 0x15, ®s[0x15], 2); |
|
/* compression register */ |
|
reg_w(gspca_dev, 0x18, ®s[0x18], 1); |
|
/* H_start */ |
|
reg_w(gspca_dev, 0x12, ®s[0x12], 1); |
|
/* V_START */ |
|
reg_w(gspca_dev, 0x13, ®s[0x13], 1); |
|
/* reset 0x17 SensorClk enable inv Clk 0x60 */ |
|
/*fixme: ov7630 [17]=68 8f (+20 if 102)*/ |
|
reg_w(gspca_dev, 0x17, ®s[0x17], 1); |
|
/*MCKSIZE ->3 */ /*fixme: not ov7630*/ |
|
reg_w(gspca_dev, 0x19, ®s[0x19], 1); |
|
/* AE_STRX AE_STRY AE_ENDX AE_ENDY */ |
|
reg_w(gspca_dev, 0x1c, ®s[0x1c], 4); |
|
/* Enable video transfert */ |
|
reg_w(gspca_dev, 0x01, ®s[0x01], 1); |
|
/* Compression */ |
|
reg_w(gspca_dev, 0x18, ®s[0x18], 2); |
|
msleep(20); |
|
|
|
sd->reg11 = -1; |
|
|
|
setgain(gspca_dev); |
|
setbrightness(gspca_dev); |
|
setexposure(gspca_dev); |
|
setfreq(gspca_dev); |
|
|
|
sd->frames_to_drop = 0; |
|
sd->autogain_ignore_frames = 0; |
|
gspca_dev->exp_too_high_cnt = 0; |
|
gspca_dev->exp_too_low_cnt = 0; |
|
atomic_set(&sd->avg_lum, -1); |
|
return gspca_dev->usb_err; |
|
} |
|
|
|
static void sd_stopN(struct gspca_dev *gspca_dev) |
|
{ |
|
sd_init(gspca_dev); |
|
} |
|
|
|
static u8* find_sof(struct gspca_dev *gspca_dev, u8 *data, int len) |
|
{ |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
int i, header_size = (sd->bridge == BRIDGE_103) ? 18 : 12; |
|
|
|
/* frames start with: |
|
* ff ff 00 c4 c4 96 synchro |
|
* 00 (unknown) |
|
* xx (frame sequence / size / compression) |
|
* (xx) (idem - extra byte for sn9c103) |
|
* ll mm brightness sum inside auto exposure |
|
* ll mm brightness sum outside auto exposure |
|
* (xx xx xx xx xx) audio values for snc103 |
|
*/ |
|
for (i = 0; i < len; i++) { |
|
switch (sd->header_read) { |
|
case 0: |
|
if (data[i] == 0xff) |
|
sd->header_read++; |
|
break; |
|
case 1: |
|
if (data[i] == 0xff) |
|
sd->header_read++; |
|
else |
|
sd->header_read = 0; |
|
break; |
|
case 2: |
|
if (data[i] == 0x00) |
|
sd->header_read++; |
|
else if (data[i] != 0xff) |
|
sd->header_read = 0; |
|
break; |
|
case 3: |
|
if (data[i] == 0xc4) |
|
sd->header_read++; |
|
else if (data[i] == 0xff) |
|
sd->header_read = 1; |
|
else |
|
sd->header_read = 0; |
|
break; |
|
case 4: |
|
if (data[i] == 0xc4) |
|
sd->header_read++; |
|
else if (data[i] == 0xff) |
|
sd->header_read = 1; |
|
else |
|
sd->header_read = 0; |
|
break; |
|
case 5: |
|
if (data[i] == 0x96) |
|
sd->header_read++; |
|
else if (data[i] == 0xff) |
|
sd->header_read = 1; |
|
else |
|
sd->header_read = 0; |
|
break; |
|
default: |
|
sd->header[sd->header_read - 6] = data[i]; |
|
sd->header_read++; |
|
if (sd->header_read == header_size) { |
|
sd->header_read = 0; |
|
return data + i + 1; |
|
} |
|
} |
|
} |
|
return NULL; |
|
} |
|
|
|
static void sd_pkt_scan(struct gspca_dev *gspca_dev, |
|
u8 *data, /* isoc packet */ |
|
int len) /* iso packet length */ |
|
{ |
|
int fr_h_sz = 0, lum_offset = 0, len_after_sof = 0; |
|
struct sd *sd = (struct sd *) gspca_dev; |
|
struct cam *cam = &gspca_dev->cam; |
|
u8 *sof; |
|
|
|
sof = find_sof(gspca_dev, data, len); |
|
if (sof) { |
|
if (sd->bridge == BRIDGE_103) { |
|
fr_h_sz = 18; |
|
lum_offset = 3; |
|
} else { |
|
fr_h_sz = 12; |
|
lum_offset = 2; |
|
} |
|
|
|
len_after_sof = len - (sof - data); |
|
len = (sof - data) - fr_h_sz; |
|
if (len < 0) |
|
len = 0; |
|
} |
|
|
|
if (cam->cam_mode[gspca_dev->curr_mode].priv & MODE_RAW) { |
|
/* In raw mode we sometimes get some garbage after the frame |
|
ignore this */ |
|
int used; |
|
int size = cam->cam_mode[gspca_dev->curr_mode].sizeimage; |
|
|
|
used = gspca_dev->image_len; |
|
if (used + len > size) |
|
len = size - used; |
|
} |
|
|
|
gspca_frame_add(gspca_dev, INTER_PACKET, data, len); |
|
|
|
if (sof) { |
|
int lum = sd->header[lum_offset] + |
|
(sd->header[lum_offset + 1] << 8); |
|
|
|
/* When exposure changes midway a frame we |
|
get a lum of 0 in this case drop 2 frames |
|
as the frames directly after an exposure |
|
change have an unstable image. Sometimes lum |
|
*really* is 0 (cam used in low light with |
|
low exposure setting), so do not drop frames |
|
if the previous lum was 0 too. */ |
|
if (lum == 0 && sd->prev_avg_lum != 0) { |
|
lum = -1; |
|
sd->frames_to_drop = 2; |
|
sd->prev_avg_lum = 0; |
|
} else |
|
sd->prev_avg_lum = lum; |
|
atomic_set(&sd->avg_lum, lum); |
|
|
|
if (sd->frames_to_drop) |
|
sd->frames_to_drop--; |
|
else |
|
gspca_frame_add(gspca_dev, LAST_PACKET, NULL, 0); |
|
|
|
gspca_frame_add(gspca_dev, FIRST_PACKET, sof, len_after_sof); |
|
} |
|
} |
|
|
|
#if IS_ENABLED(CONFIG_INPUT) |
|
static int sd_int_pkt_scan(struct gspca_dev *gspca_dev, |
|
u8 *data, /* interrupt packet data */ |
|
int len) /* interrupt packet length */ |
|
{ |
|
int ret = -EINVAL; |
|
|
|
if (len == 1 && data[0] == 1) { |
|
input_report_key(gspca_dev->input_dev, KEY_CAMERA, 1); |
|
input_sync(gspca_dev->input_dev); |
|
input_report_key(gspca_dev->input_dev, KEY_CAMERA, 0); |
|
input_sync(gspca_dev->input_dev); |
|
ret = 0; |
|
} |
|
|
|
return ret; |
|
} |
|
#endif |
|
|
|
/* sub-driver description */ |
|
static const struct sd_desc sd_desc = { |
|
.name = MODULE_NAME, |
|
.config = sd_config, |
|
.init = sd_init, |
|
.init_controls = sd_init_controls, |
|
.start = sd_start, |
|
.stopN = sd_stopN, |
|
.pkt_scan = sd_pkt_scan, |
|
.dq_callback = do_autogain, |
|
#if IS_ENABLED(CONFIG_INPUT) |
|
.int_pkt_scan = sd_int_pkt_scan, |
|
#endif |
|
}; |
|
|
|
/* -- module initialisation -- */ |
|
#define SB(sensor, bridge) \ |
|
.driver_info = (SENSOR_ ## sensor << 8) | BRIDGE_ ## bridge |
|
|
|
|
|
static const struct usb_device_id device_table[] = { |
|
{USB_DEVICE(0x0c45, 0x6001), SB(TAS5110C, 102)}, /* TAS5110C1B */ |
|
{USB_DEVICE(0x0c45, 0x6005), SB(TAS5110C, 101)}, /* TAS5110C1B */ |
|
{USB_DEVICE(0x0c45, 0x6007), SB(TAS5110D, 101)}, /* TAS5110D */ |
|
{USB_DEVICE(0x0c45, 0x6009), SB(PAS106, 101)}, |
|
{USB_DEVICE(0x0c45, 0x600d), SB(PAS106, 101)}, |
|
{USB_DEVICE(0x0c45, 0x6011), SB(OV6650, 101)}, |
|
{USB_DEVICE(0x0c45, 0x6019), SB(OV7630, 101)}, |
|
{USB_DEVICE(0x0c45, 0x6024), SB(TAS5130CXX, 102)}, |
|
{USB_DEVICE(0x0c45, 0x6025), SB(TAS5130CXX, 102)}, |
|
{USB_DEVICE(0x0c45, 0x6027), SB(OV7630, 101)}, /* Genius Eye 310 */ |
|
{USB_DEVICE(0x0c45, 0x6028), SB(PAS202, 102)}, |
|
{USB_DEVICE(0x0c45, 0x6029), SB(PAS106, 102)}, |
|
{USB_DEVICE(0x0c45, 0x602a), SB(HV7131D, 102)}, |
|
/* {USB_DEVICE(0x0c45, 0x602b), SB(MI0343, 102)}, */ |
|
{USB_DEVICE(0x0c45, 0x602c), SB(OV7630, 102)}, |
|
{USB_DEVICE(0x0c45, 0x602d), SB(HV7131R, 102)}, |
|
{USB_DEVICE(0x0c45, 0x602e), SB(OV7630, 102)}, |
|
/* {USB_DEVICE(0x0c45, 0x6030), SB(MI03XX, 102)}, */ /* MI0343 MI0360 MI0330 */ |
|
/* {USB_DEVICE(0x0c45, 0x6082), SB(MI03XX, 103)}, */ /* MI0343 MI0360 */ |
|
{USB_DEVICE(0x0c45, 0x6083), SB(HV7131D, 103)}, |
|
{USB_DEVICE(0x0c45, 0x608c), SB(HV7131R, 103)}, |
|
/* {USB_DEVICE(0x0c45, 0x608e), SB(CISVF10, 103)}, */ |
|
{USB_DEVICE(0x0c45, 0x608f), SB(OV7630, 103)}, |
|
{USB_DEVICE(0x0c45, 0x60a8), SB(PAS106, 103)}, |
|
{USB_DEVICE(0x0c45, 0x60aa), SB(TAS5130CXX, 103)}, |
|
{USB_DEVICE(0x0c45, 0x60af), SB(PAS202, 103)}, |
|
{USB_DEVICE(0x0c45, 0x60b0), SB(OV7630, 103)}, |
|
{} |
|
}; |
|
MODULE_DEVICE_TABLE(usb, device_table); |
|
|
|
/* -- device connect -- */ |
|
static int sd_probe(struct usb_interface *intf, |
|
const struct usb_device_id *id) |
|
{ |
|
return gspca_dev_probe(intf, id, &sd_desc, sizeof(struct sd), |
|
THIS_MODULE); |
|
} |
|
|
|
static struct usb_driver sd_driver = { |
|
.name = MODULE_NAME, |
|
.id_table = device_table, |
|
.probe = sd_probe, |
|
.disconnect = gspca_disconnect, |
|
#ifdef CONFIG_PM |
|
.suspend = gspca_suspend, |
|
.resume = gspca_resume, |
|
.reset_resume = gspca_resume, |
|
#endif |
|
}; |
|
|
|
module_usb_driver(sd_driver);
|
|
|