forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
79 lines
2.3 KiB
79 lines
2.3 KiB
# SPDX-License-Identifier: GPL-2.0-only |
|
config IR_IMG |
|
tristate "ImgTec IR Decoder" |
|
depends on RC_CORE |
|
depends on MIPS || COMPILE_TEST |
|
select IR_IMG_HW if !IR_IMG_RAW |
|
help |
|
Say Y or M here if you want to use the ImgTec infrared decoder |
|
functionality found in SoCs such as TZ1090. |
|
|
|
config IR_IMG_RAW |
|
bool "Raw decoder" |
|
depends on IR_IMG |
|
help |
|
Say Y here to enable the raw mode driver which passes raw IR signal |
|
changes to the IR raw decoders for software decoding. This is much |
|
less reliable (due to lack of timestamps) and consumes more |
|
processing power than using hardware decode, but can be useful for |
|
testing, debug, and to make more protocols available. |
|
|
|
config IR_IMG_HW |
|
bool "Hardware decoder" |
|
depends on IR_IMG |
|
help |
|
Say Y here to enable the hardware decode driver which decodes the IR |
|
signals in hardware. This is more reliable, consumes less processing |
|
power since only a single interrupt is received for each scancode, |
|
and allows an IR scancode to be used as a wake event. |
|
|
|
config IR_IMG_NEC |
|
bool "NEC protocol support" |
|
depends on IR_IMG_HW |
|
select BITREVERSE |
|
help |
|
Say Y here to enable support for the NEC, extended NEC, and 32-bit |
|
NEC protocols in the ImgTec infrared decoder block. |
|
|
|
config IR_IMG_JVC |
|
bool "JVC protocol support" |
|
depends on IR_IMG_HW |
|
help |
|
Say Y here to enable support for the JVC protocol in the ImgTec |
|
infrared decoder block. |
|
|
|
config IR_IMG_SONY |
|
bool "Sony protocol support" |
|
depends on IR_IMG_HW |
|
help |
|
Say Y here to enable support for the Sony protocol in the ImgTec |
|
infrared decoder block. |
|
|
|
config IR_IMG_SHARP |
|
bool "Sharp protocol support" |
|
depends on IR_IMG_HW |
|
help |
|
Say Y here to enable support for the Sharp protocol in the ImgTec |
|
infrared decoder block. |
|
|
|
config IR_IMG_SANYO |
|
bool "Sanyo protocol support" |
|
depends on IR_IMG_HW |
|
help |
|
Say Y here to enable support for the Sanyo protocol (used by Sanyo, |
|
Aiwa, Chinon remotes) in the ImgTec infrared decoder block. |
|
|
|
config IR_IMG_RC5 |
|
bool "Philips RC5 protocol support" |
|
depends on IR_IMG_HW |
|
help |
|
Say Y here to enable support for the RC5 protocol in the ImgTec |
|
infrared decoder block. |
|
|
|
config IR_IMG_RC6 |
|
bool "Philips RC6 protocol support" |
|
depends on IR_IMG_HW |
|
help |
|
Say Y here to enable support for the RC6 protocol in the ImgTec |
|
infrared decoder block. |
|
Note: This version only supports mode 0.
|
|
|