forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
192 lines
5.2 KiB
192 lines
5.2 KiB
// SPDX-License-Identifier: GPL-2.0-only |
|
/* |
|
* Backlight driver for the Kinetic KTD253 |
|
* Based on code and know-how from the Samsung GT-S7710 |
|
* Gareth Phillips <[email protected]> |
|
*/ |
|
#include <linux/backlight.h> |
|
#include <linux/delay.h> |
|
#include <linux/err.h> |
|
#include <linux/fb.h> |
|
#include <linux/gpio/consumer.h> |
|
#include <linux/init.h> |
|
#include <linux/kernel.h> |
|
#include <linux/limits.h> |
|
#include <linux/module.h> |
|
#include <linux/of.h> |
|
#include <linux/platform_device.h> |
|
#include <linux/property.h> |
|
#include <linux/slab.h> |
|
|
|
/* Current ratio is n/32 from 1/32 to 32/32 */ |
|
#define KTD253_MIN_RATIO 1 |
|
#define KTD253_MAX_RATIO 32 |
|
#define KTD253_DEFAULT_RATIO 13 |
|
|
|
#define KTD253_T_LOW_NS (200 + 10) /* Additional 10ns as safety factor */ |
|
#define KTD253_T_HIGH_NS (200 + 10) /* Additional 10ns as safety factor */ |
|
#define KTD253_T_OFF_MS 3 |
|
|
|
struct ktd253_backlight { |
|
struct device *dev; |
|
struct backlight_device *bl; |
|
struct gpio_desc *gpiod; |
|
u16 ratio; |
|
}; |
|
|
|
static int ktd253_backlight_update_status(struct backlight_device *bl) |
|
{ |
|
struct ktd253_backlight *ktd253 = bl_get_data(bl); |
|
int brightness = backlight_get_brightness(bl); |
|
u16 target_ratio; |
|
u16 current_ratio = ktd253->ratio; |
|
unsigned long flags; |
|
|
|
dev_dbg(ktd253->dev, "new brightness/ratio: %d/32\n", brightness); |
|
|
|
target_ratio = brightness; |
|
|
|
if (target_ratio == current_ratio) |
|
/* This is already right */ |
|
return 0; |
|
|
|
if (target_ratio == 0) { |
|
gpiod_set_value_cansleep(ktd253->gpiod, 0); |
|
/* |
|
* We need to keep the GPIO low for at least this long |
|
* to actually switch the KTD253 off. |
|
*/ |
|
msleep(KTD253_T_OFF_MS); |
|
ktd253->ratio = 0; |
|
return 0; |
|
} |
|
|
|
if (current_ratio == 0) { |
|
gpiod_set_value_cansleep(ktd253->gpiod, 1); |
|
ndelay(KTD253_T_HIGH_NS); |
|
/* We always fall back to this when we power on */ |
|
current_ratio = KTD253_MAX_RATIO; |
|
} |
|
|
|
/* |
|
* WARNING: |
|
* The loop to set the correct current level is performed |
|
* with interrupts disabled as it is timing critical. |
|
* The maximum number of cycles of the loop is 32 |
|
* so the time taken will be (T_LOW_NS + T_HIGH_NS + loop_time) * 32, |
|
*/ |
|
local_irq_save(flags); |
|
while (current_ratio != target_ratio) { |
|
/* |
|
* These GPIO operations absolutely can NOT sleep so no |
|
* _cansleep suffixes, and no using GPIO expanders on |
|
* slow buses for this! |
|
*/ |
|
gpiod_set_value(ktd253->gpiod, 0); |
|
ndelay(KTD253_T_LOW_NS); |
|
gpiod_set_value(ktd253->gpiod, 1); |
|
ndelay(KTD253_T_HIGH_NS); |
|
/* After 1/32 we loop back to 32/32 */ |
|
if (current_ratio == KTD253_MIN_RATIO) |
|
current_ratio = KTD253_MAX_RATIO; |
|
else |
|
current_ratio--; |
|
} |
|
local_irq_restore(flags); |
|
ktd253->ratio = current_ratio; |
|
|
|
dev_dbg(ktd253->dev, "new ratio set to %d/32\n", target_ratio); |
|
|
|
return 0; |
|
} |
|
|
|
static const struct backlight_ops ktd253_backlight_ops = { |
|
.options = BL_CORE_SUSPENDRESUME, |
|
.update_status = ktd253_backlight_update_status, |
|
}; |
|
|
|
static int ktd253_backlight_probe(struct platform_device *pdev) |
|
{ |
|
struct device *dev = &pdev->dev; |
|
struct backlight_device *bl; |
|
struct ktd253_backlight *ktd253; |
|
u32 max_brightness; |
|
u32 brightness; |
|
int ret; |
|
|
|
ktd253 = devm_kzalloc(dev, sizeof(*ktd253), GFP_KERNEL); |
|
if (!ktd253) |
|
return -ENOMEM; |
|
ktd253->dev = dev; |
|
|
|
ret = device_property_read_u32(dev, "max-brightness", &max_brightness); |
|
if (ret) |
|
max_brightness = KTD253_MAX_RATIO; |
|
if (max_brightness > KTD253_MAX_RATIO) { |
|
/* Clamp brightness to hardware max */ |
|
dev_err(dev, "illegal max brightness specified\n"); |
|
max_brightness = KTD253_MAX_RATIO; |
|
} |
|
|
|
ret = device_property_read_u32(dev, "default-brightness", &brightness); |
|
if (ret) |
|
brightness = KTD253_DEFAULT_RATIO; |
|
if (brightness > max_brightness) { |
|
/* Clamp default brightness to max brightness */ |
|
dev_err(dev, "default brightness exceeds max brightness\n"); |
|
brightness = max_brightness; |
|
} |
|
|
|
ktd253->gpiod = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW); |
|
if (IS_ERR(ktd253->gpiod)) { |
|
ret = PTR_ERR(ktd253->gpiod); |
|
if (ret != -EPROBE_DEFER) |
|
dev_err(dev, "gpio line missing or invalid.\n"); |
|
return ret; |
|
} |
|
gpiod_set_consumer_name(ktd253->gpiod, dev_name(dev)); |
|
/* Bring backlight to a known off state */ |
|
msleep(KTD253_T_OFF_MS); |
|
|
|
bl = devm_backlight_device_register(dev, dev_name(dev), dev, ktd253, |
|
&ktd253_backlight_ops, NULL); |
|
if (IS_ERR(bl)) { |
|
dev_err(dev, "failed to register backlight\n"); |
|
return PTR_ERR(bl); |
|
} |
|
bl->props.max_brightness = max_brightness; |
|
/* When we just enable the GPIO line we set max brightness */ |
|
if (brightness) { |
|
bl->props.brightness = brightness; |
|
bl->props.power = FB_BLANK_UNBLANK; |
|
} else { |
|
bl->props.brightness = 0; |
|
bl->props.power = FB_BLANK_POWERDOWN; |
|
} |
|
|
|
ktd253->bl = bl; |
|
platform_set_drvdata(pdev, bl); |
|
backlight_update_status(bl); |
|
|
|
return 0; |
|
} |
|
|
|
static const struct of_device_id ktd253_backlight_of_match[] = { |
|
{ .compatible = "kinetic,ktd253" }, |
|
{ /* sentinel */ } |
|
}; |
|
MODULE_DEVICE_TABLE(of, ktd253_backlight_of_match); |
|
|
|
static struct platform_driver ktd253_backlight_driver = { |
|
.driver = { |
|
.name = "ktd253-backlight", |
|
.of_match_table = ktd253_backlight_of_match, |
|
}, |
|
.probe = ktd253_backlight_probe, |
|
}; |
|
module_platform_driver(ktd253_backlight_driver); |
|
|
|
MODULE_AUTHOR("Linus Walleij <[email protected]>"); |
|
MODULE_DESCRIPTION("Kinetic KTD253 Backlight Driver"); |
|
MODULE_LICENSE("GPL"); |
|
MODULE_ALIAS("platform:ktd253-backlight");
|
|
|