forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
498 lines
14 KiB
498 lines
14 KiB
// SPDX-License-Identifier: GPL-2.0-only |
|
/* |
|
* Cyrix MediaGX and NatSemi Geode Suspend Modulation |
|
* (C) 2002 Zwane Mwaikambo <[email protected]> |
|
* (C) 2002 Hiroshi Miura <[email protected]> |
|
* All Rights Reserved |
|
* |
|
* The author(s) of this software shall not be held liable for damages |
|
* of any nature resulting due to the use of this software. This |
|
* software is provided AS-IS with no warranties. |
|
* |
|
* Theoretical note: |
|
* |
|
* (see Geode(tm) CS5530 manual (rev.4.1) page.56) |
|
* |
|
* CPU frequency control on NatSemi Geode GX1/GXLV processor and CS55x0 |
|
* are based on Suspend Modulation. |
|
* |
|
* Suspend Modulation works by asserting and de-asserting the SUSP# pin |
|
* to CPU(GX1/GXLV) for configurable durations. When asserting SUSP# |
|
* the CPU enters an idle state. GX1 stops its core clock when SUSP# is |
|
* asserted then power consumption is reduced. |
|
* |
|
* Suspend Modulation's OFF/ON duration are configurable |
|
* with 'Suspend Modulation OFF Count Register' |
|
* and 'Suspend Modulation ON Count Register'. |
|
* These registers are 8bit counters that represent the number of |
|
* 32us intervals which the SUSP# pin is asserted(ON)/de-asserted(OFF) |
|
* to the processor. |
|
* |
|
* These counters define a ratio which is the effective frequency |
|
* of operation of the system. |
|
* |
|
* OFF Count |
|
* F_eff = Fgx * ---------------------- |
|
* OFF Count + ON Count |
|
* |
|
* 0 <= On Count, Off Count <= 255 |
|
* |
|
* From these limits, we can get register values |
|
* |
|
* off_duration + on_duration <= MAX_DURATION |
|
* on_duration = off_duration * (stock_freq - freq) / freq |
|
* |
|
* off_duration = (freq * DURATION) / stock_freq |
|
* on_duration = DURATION - off_duration |
|
* |
|
*--------------------------------------------------------------------------- |
|
* |
|
* ChangeLog: |
|
* Dec. 12, 2003 Hiroshi Miura <[email protected]> |
|
* - fix on/off register mistake |
|
* - fix cpu_khz calc when it stops cpu modulation. |
|
* |
|
* Dec. 11, 2002 Hiroshi Miura <[email protected]> |
|
* - rewrite for Cyrix MediaGX Cx5510/5520 and |
|
* NatSemi Geode Cs5530(A). |
|
* |
|
* Jul. ??, 2002 Zwane Mwaikambo <[email protected]> |
|
* - cs5530_mod patch for 2.4.19-rc1. |
|
* |
|
*--------------------------------------------------------------------------- |
|
* |
|
* Todo |
|
* Test on machines with 5510, 5530, 5530A |
|
*/ |
|
|
|
/************************************************************************ |
|
* Suspend Modulation - Definitions * |
|
************************************************************************/ |
|
|
|
#include <linux/kernel.h> |
|
#include <linux/module.h> |
|
#include <linux/init.h> |
|
#include <linux/smp.h> |
|
#include <linux/cpufreq.h> |
|
#include <linux/pci.h> |
|
#include <linux/errno.h> |
|
#include <linux/slab.h> |
|
|
|
#include <asm/cpu_device_id.h> |
|
#include <asm/processor-cyrix.h> |
|
|
|
/* PCI config registers, all at F0 */ |
|
#define PCI_PMER1 0x80 /* power management enable register 1 */ |
|
#define PCI_PMER2 0x81 /* power management enable register 2 */ |
|
#define PCI_PMER3 0x82 /* power management enable register 3 */ |
|
#define PCI_IRQTC 0x8c /* irq speedup timer counter register:typical 2 to 4ms */ |
|
#define PCI_VIDTC 0x8d /* video speedup timer counter register: typical 50 to 100ms */ |
|
#define PCI_MODOFF 0x94 /* suspend modulation OFF counter register, 1 = 32us */ |
|
#define PCI_MODON 0x95 /* suspend modulation ON counter register */ |
|
#define PCI_SUSCFG 0x96 /* suspend configuration register */ |
|
|
|
/* PMER1 bits */ |
|
#define GPM (1<<0) /* global power management */ |
|
#define GIT (1<<1) /* globally enable PM device idle timers */ |
|
#define GTR (1<<2) /* globally enable IO traps */ |
|
#define IRQ_SPDUP (1<<3) /* disable clock throttle during interrupt handling */ |
|
#define VID_SPDUP (1<<4) /* disable clock throttle during vga video handling */ |
|
|
|
/* SUSCFG bits */ |
|
#define SUSMOD (1<<0) /* enable/disable suspend modulation */ |
|
/* the below is supported only with cs5530 (after rev.1.2)/cs5530A */ |
|
#define SMISPDUP (1<<1) /* select how SMI re-enable suspend modulation: */ |
|
/* IRQTC timer or read SMI speedup disable reg.(F1BAR[08-09h]) */ |
|
#define SUSCFG (1<<2) /* enable powering down a GXLV processor. "Special 3Volt Suspend" mode */ |
|
/* the below is supported only with cs5530A */ |
|
#define PWRSVE_ISA (1<<3) /* stop ISA clock */ |
|
#define PWRSVE (1<<4) /* active idle */ |
|
|
|
struct gxfreq_params { |
|
u8 on_duration; |
|
u8 off_duration; |
|
u8 pci_suscfg; |
|
u8 pci_pmer1; |
|
u8 pci_pmer2; |
|
struct pci_dev *cs55x0; |
|
}; |
|
|
|
static struct gxfreq_params *gx_params; |
|
static int stock_freq; |
|
|
|
/* PCI bus clock - defaults to 30.000 if cpu_khz is not available */ |
|
static int pci_busclk; |
|
module_param(pci_busclk, int, 0444); |
|
|
|
/* maximum duration for which the cpu may be suspended |
|
* (32us * MAX_DURATION). If no parameter is given, this defaults |
|
* to 255. |
|
* Note that this leads to a maximum of 8 ms(!) where the CPU clock |
|
* is suspended -- processing power is just 0.39% of what it used to be, |
|
* though. 781.25 kHz(!) for a 200 MHz processor -- wow. */ |
|
static int max_duration = 255; |
|
module_param(max_duration, int, 0444); |
|
|
|
/* For the default policy, we want at least some processing power |
|
* - let's say 5%. (min = maxfreq / POLICY_MIN_DIV) |
|
*/ |
|
#define POLICY_MIN_DIV 20 |
|
|
|
|
|
/** |
|
* we can detect a core multiplier from dir0_lsb |
|
* from GX1 datasheet p.56, |
|
* MULT[3:0]: |
|
* 0000 = SYSCLK multiplied by 4 (test only) |
|
* 0001 = SYSCLK multiplied by 10 |
|
* 0010 = SYSCLK multiplied by 4 |
|
* 0011 = SYSCLK multiplied by 6 |
|
* 0100 = SYSCLK multiplied by 9 |
|
* 0101 = SYSCLK multiplied by 5 |
|
* 0110 = SYSCLK multiplied by 7 |
|
* 0111 = SYSCLK multiplied by 8 |
|
* of 33.3MHz |
|
**/ |
|
static int gx_freq_mult[16] = { |
|
4, 10, 4, 6, 9, 5, 7, 8, |
|
0, 0, 0, 0, 0, 0, 0, 0 |
|
}; |
|
|
|
|
|
/**************************************************************** |
|
* Low Level chipset interface * |
|
****************************************************************/ |
|
static struct pci_device_id gx_chipset_tbl[] __initdata = { |
|
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5530_LEGACY), }, |
|
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5520), }, |
|
{ PCI_VDEVICE(CYRIX, PCI_DEVICE_ID_CYRIX_5510), }, |
|
{ 0, }, |
|
}; |
|
MODULE_DEVICE_TABLE(pci, gx_chipset_tbl); |
|
|
|
static void gx_write_byte(int reg, int value) |
|
{ |
|
pci_write_config_byte(gx_params->cs55x0, reg, value); |
|
} |
|
|
|
/** |
|
* gx_detect_chipset: |
|
* |
|
**/ |
|
static struct pci_dev * __init gx_detect_chipset(void) |
|
{ |
|
struct pci_dev *gx_pci = NULL; |
|
|
|
/* detect which companion chip is used */ |
|
for_each_pci_dev(gx_pci) { |
|
if ((pci_match_id(gx_chipset_tbl, gx_pci)) != NULL) |
|
return gx_pci; |
|
} |
|
|
|
pr_debug("error: no supported chipset found!\n"); |
|
return NULL; |
|
} |
|
|
|
/** |
|
* gx_get_cpuspeed: |
|
* |
|
* Finds out at which efficient frequency the Cyrix MediaGX/NatSemi |
|
* Geode CPU runs. |
|
*/ |
|
static unsigned int gx_get_cpuspeed(unsigned int cpu) |
|
{ |
|
if ((gx_params->pci_suscfg & SUSMOD) == 0) |
|
return stock_freq; |
|
|
|
return (stock_freq * gx_params->off_duration) |
|
/ (gx_params->on_duration + gx_params->off_duration); |
|
} |
|
|
|
/** |
|
* gx_validate_speed: |
|
* determine current cpu speed |
|
* |
|
**/ |
|
|
|
static unsigned int gx_validate_speed(unsigned int khz, u8 *on_duration, |
|
u8 *off_duration) |
|
{ |
|
unsigned int i; |
|
u8 tmp_on, tmp_off; |
|
int old_tmp_freq = stock_freq; |
|
int tmp_freq; |
|
|
|
*off_duration = 1; |
|
*on_duration = 0; |
|
|
|
for (i = max_duration; i > 0; i--) { |
|
tmp_off = ((khz * i) / stock_freq) & 0xff; |
|
tmp_on = i - tmp_off; |
|
tmp_freq = (stock_freq * tmp_off) / i; |
|
/* if this relation is closer to khz, use this. If it's equal, |
|
* prefer it, too - lower latency */ |
|
if (abs(tmp_freq - khz) <= abs(old_tmp_freq - khz)) { |
|
*on_duration = tmp_on; |
|
*off_duration = tmp_off; |
|
old_tmp_freq = tmp_freq; |
|
} |
|
} |
|
|
|
return old_tmp_freq; |
|
} |
|
|
|
|
|
/** |
|
* gx_set_cpuspeed: |
|
* set cpu speed in khz. |
|
**/ |
|
|
|
static void gx_set_cpuspeed(struct cpufreq_policy *policy, unsigned int khz) |
|
{ |
|
u8 suscfg, pmer1; |
|
unsigned int new_khz; |
|
unsigned long flags; |
|
struct cpufreq_freqs freqs; |
|
|
|
freqs.old = gx_get_cpuspeed(0); |
|
|
|
new_khz = gx_validate_speed(khz, &gx_params->on_duration, |
|
&gx_params->off_duration); |
|
|
|
freqs.new = new_khz; |
|
|
|
cpufreq_freq_transition_begin(policy, &freqs); |
|
local_irq_save(flags); |
|
|
|
if (new_khz != stock_freq) { |
|
/* if new khz == 100% of CPU speed, it is special case */ |
|
switch (gx_params->cs55x0->device) { |
|
case PCI_DEVICE_ID_CYRIX_5530_LEGACY: |
|
pmer1 = gx_params->pci_pmer1 | IRQ_SPDUP | VID_SPDUP; |
|
/* FIXME: need to test other values -- Zwane,Miura */ |
|
/* typical 2 to 4ms */ |
|
gx_write_byte(PCI_IRQTC, 4); |
|
/* typical 50 to 100ms */ |
|
gx_write_byte(PCI_VIDTC, 100); |
|
gx_write_byte(PCI_PMER1, pmer1); |
|
|
|
if (gx_params->cs55x0->revision < 0x10) { |
|
/* CS5530(rev 1.2, 1.3) */ |
|
suscfg = gx_params->pci_suscfg|SUSMOD; |
|
} else { |
|
/* CS5530A,B.. */ |
|
suscfg = gx_params->pci_suscfg|SUSMOD|PWRSVE; |
|
} |
|
break; |
|
case PCI_DEVICE_ID_CYRIX_5520: |
|
case PCI_DEVICE_ID_CYRIX_5510: |
|
suscfg = gx_params->pci_suscfg | SUSMOD; |
|
break; |
|
default: |
|
local_irq_restore(flags); |
|
pr_debug("fatal: try to set unknown chipset.\n"); |
|
return; |
|
} |
|
} else { |
|
suscfg = gx_params->pci_suscfg & ~(SUSMOD); |
|
gx_params->off_duration = 0; |
|
gx_params->on_duration = 0; |
|
pr_debug("suspend modulation disabled: cpu runs 100%% speed.\n"); |
|
} |
|
|
|
gx_write_byte(PCI_MODOFF, gx_params->off_duration); |
|
gx_write_byte(PCI_MODON, gx_params->on_duration); |
|
|
|
gx_write_byte(PCI_SUSCFG, suscfg); |
|
pci_read_config_byte(gx_params->cs55x0, PCI_SUSCFG, &suscfg); |
|
|
|
local_irq_restore(flags); |
|
|
|
gx_params->pci_suscfg = suscfg; |
|
|
|
cpufreq_freq_transition_end(policy, &freqs, 0); |
|
|
|
pr_debug("suspend modulation w/ duration of ON:%d us, OFF:%d us\n", |
|
gx_params->on_duration * 32, gx_params->off_duration * 32); |
|
pr_debug("suspend modulation w/ clock speed: %d kHz.\n", freqs.new); |
|
} |
|
|
|
/**************************************************************** |
|
* High level functions * |
|
****************************************************************/ |
|
|
|
/* |
|
* cpufreq_gx_verify: test if frequency range is valid |
|
* |
|
* This function checks if a given frequency range in kHz is valid |
|
* for the hardware supported by the driver. |
|
*/ |
|
|
|
static int cpufreq_gx_verify(struct cpufreq_policy_data *policy) |
|
{ |
|
unsigned int tmp_freq = 0; |
|
u8 tmp1, tmp2; |
|
|
|
if (!stock_freq || !policy) |
|
return -EINVAL; |
|
|
|
policy->cpu = 0; |
|
cpufreq_verify_within_limits(policy, (stock_freq / max_duration), |
|
stock_freq); |
|
|
|
/* it needs to be assured that at least one supported frequency is |
|
* within policy->min and policy->max. If it is not, policy->max |
|
* needs to be increased until one frequency is supported. |
|
* policy->min may not be decreased, though. This way we guarantee a |
|
* specific processing capacity. |
|
*/ |
|
tmp_freq = gx_validate_speed(policy->min, &tmp1, &tmp2); |
|
if (tmp_freq < policy->min) |
|
tmp_freq += stock_freq / max_duration; |
|
policy->min = tmp_freq; |
|
if (policy->min > policy->max) |
|
policy->max = tmp_freq; |
|
tmp_freq = gx_validate_speed(policy->max, &tmp1, &tmp2); |
|
if (tmp_freq > policy->max) |
|
tmp_freq -= stock_freq / max_duration; |
|
policy->max = tmp_freq; |
|
if (policy->max < policy->min) |
|
policy->max = policy->min; |
|
cpufreq_verify_within_limits(policy, (stock_freq / max_duration), |
|
stock_freq); |
|
|
|
return 0; |
|
} |
|
|
|
/* |
|
* cpufreq_gx_target: |
|
* |
|
*/ |
|
static int cpufreq_gx_target(struct cpufreq_policy *policy, |
|
unsigned int target_freq, |
|
unsigned int relation) |
|
{ |
|
u8 tmp1, tmp2; |
|
unsigned int tmp_freq; |
|
|
|
if (!stock_freq || !policy) |
|
return -EINVAL; |
|
|
|
policy->cpu = 0; |
|
|
|
tmp_freq = gx_validate_speed(target_freq, &tmp1, &tmp2); |
|
while (tmp_freq < policy->min) { |
|
tmp_freq += stock_freq / max_duration; |
|
tmp_freq = gx_validate_speed(tmp_freq, &tmp1, &tmp2); |
|
} |
|
while (tmp_freq > policy->max) { |
|
tmp_freq -= stock_freq / max_duration; |
|
tmp_freq = gx_validate_speed(tmp_freq, &tmp1, &tmp2); |
|
} |
|
|
|
gx_set_cpuspeed(policy, tmp_freq); |
|
|
|
return 0; |
|
} |
|
|
|
static int cpufreq_gx_cpu_init(struct cpufreq_policy *policy) |
|
{ |
|
unsigned int maxfreq; |
|
|
|
if (!policy || policy->cpu != 0) |
|
return -ENODEV; |
|
|
|
/* determine maximum frequency */ |
|
if (pci_busclk) |
|
maxfreq = pci_busclk * gx_freq_mult[getCx86(CX86_DIR1) & 0x0f]; |
|
else if (cpu_khz) |
|
maxfreq = cpu_khz; |
|
else |
|
maxfreq = 30000 * gx_freq_mult[getCx86(CX86_DIR1) & 0x0f]; |
|
|
|
stock_freq = maxfreq; |
|
|
|
pr_debug("cpu max frequency is %d.\n", maxfreq); |
|
|
|
/* setup basic struct for cpufreq API */ |
|
policy->cpu = 0; |
|
|
|
if (max_duration < POLICY_MIN_DIV) |
|
policy->min = maxfreq / max_duration; |
|
else |
|
policy->min = maxfreq / POLICY_MIN_DIV; |
|
policy->max = maxfreq; |
|
policy->cpuinfo.min_freq = maxfreq / max_duration; |
|
policy->cpuinfo.max_freq = maxfreq; |
|
|
|
return 0; |
|
} |
|
|
|
/* |
|
* cpufreq_gx_init: |
|
* MediaGX/Geode GX initialize cpufreq driver |
|
*/ |
|
static struct cpufreq_driver gx_suspmod_driver = { |
|
.flags = CPUFREQ_NO_AUTO_DYNAMIC_SWITCHING, |
|
.get = gx_get_cpuspeed, |
|
.verify = cpufreq_gx_verify, |
|
.target = cpufreq_gx_target, |
|
.init = cpufreq_gx_cpu_init, |
|
.name = "gx-suspmod", |
|
}; |
|
|
|
static int __init cpufreq_gx_init(void) |
|
{ |
|
int ret; |
|
struct gxfreq_params *params; |
|
struct pci_dev *gx_pci; |
|
|
|
/* Test if we have the right hardware */ |
|
gx_pci = gx_detect_chipset(); |
|
if (gx_pci == NULL) |
|
return -ENODEV; |
|
|
|
/* check whether module parameters are sane */ |
|
if (max_duration > 0xff) |
|
max_duration = 0xff; |
|
|
|
pr_debug("geode suspend modulation available.\n"); |
|
|
|
params = kzalloc(sizeof(*params), GFP_KERNEL); |
|
if (params == NULL) |
|
return -ENOMEM; |
|
|
|
params->cs55x0 = gx_pci; |
|
gx_params = params; |
|
|
|
/* keep cs55x0 configurations */ |
|
pci_read_config_byte(params->cs55x0, PCI_SUSCFG, &(params->pci_suscfg)); |
|
pci_read_config_byte(params->cs55x0, PCI_PMER1, &(params->pci_pmer1)); |
|
pci_read_config_byte(params->cs55x0, PCI_PMER2, &(params->pci_pmer2)); |
|
pci_read_config_byte(params->cs55x0, PCI_MODON, &(params->on_duration)); |
|
pci_read_config_byte(params->cs55x0, PCI_MODOFF, |
|
&(params->off_duration)); |
|
|
|
ret = cpufreq_register_driver(&gx_suspmod_driver); |
|
if (ret) { |
|
kfree(params); |
|
return ret; /* register error! */ |
|
} |
|
|
|
return 0; |
|
} |
|
|
|
static void __exit cpufreq_gx_exit(void) |
|
{ |
|
cpufreq_unregister_driver(&gx_suspmod_driver); |
|
pci_dev_put(gx_params->cs55x0); |
|
kfree(gx_params); |
|
} |
|
|
|
MODULE_AUTHOR("Hiroshi Miura <[email protected]>"); |
|
MODULE_DESCRIPTION("Cpufreq driver for Cyrix MediaGX and NatSemi Geode"); |
|
MODULE_LICENSE("GPL"); |
|
|
|
module_init(cpufreq_gx_init); |
|
module_exit(cpufreq_gx_exit); |
|
|
|
|