forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
503 lines
11 KiB
503 lines
11 KiB
// SPDX-License-Identifier: GPL-2.0-only |
|
/* |
|
* tm6000-input.c - driver for TM5600/TM6000/TM6010 USB video capture devices |
|
* |
|
* Copyright (C) 2010 Stefan Ringel <[email protected]> |
|
*/ |
|
|
|
#include <linux/module.h> |
|
#include <linux/init.h> |
|
#include <linux/delay.h> |
|
|
|
#include <linux/input.h> |
|
#include <linux/usb.h> |
|
|
|
#include <media/rc-core.h> |
|
|
|
#include "tm6000.h" |
|
#include "tm6000-regs.h" |
|
|
|
static unsigned int ir_debug; |
|
module_param(ir_debug, int, 0644); |
|
MODULE_PARM_DESC(ir_debug, "debug message level"); |
|
|
|
static unsigned int enable_ir = 1; |
|
module_param(enable_ir, int, 0644); |
|
MODULE_PARM_DESC(enable_ir, "enable ir (default is enable)"); |
|
|
|
static unsigned int ir_clock_mhz = 12; |
|
module_param(ir_clock_mhz, int, 0644); |
|
MODULE_PARM_DESC(ir_clock_mhz, "ir clock, in MHz"); |
|
|
|
#define URB_SUBMIT_DELAY 100 /* ms - Delay to submit an URB request on retrial and init */ |
|
#define URB_INT_LED_DELAY 100 /* ms - Delay to turn led on again on int mode */ |
|
|
|
#undef dprintk |
|
|
|
#define dprintk(level, fmt, arg...) do {\ |
|
if (ir_debug >= level) \ |
|
printk(KERN_DEBUG "%s/ir: " fmt, ir->name , ## arg); \ |
|
} while (0) |
|
|
|
struct tm6000_ir_poll_result { |
|
u16 rc_data; |
|
}; |
|
|
|
struct tm6000_IR { |
|
struct tm6000_core *dev; |
|
struct rc_dev *rc; |
|
char name[32]; |
|
char phys[32]; |
|
|
|
/* poll expernal decoder */ |
|
int polling; |
|
struct delayed_work work; |
|
u8 wait:1; |
|
u8 pwled:2; |
|
u8 submit_urb:1; |
|
struct urb *int_urb; |
|
|
|
/* IR device properties */ |
|
u64 rc_proto; |
|
}; |
|
|
|
void tm6000_ir_wait(struct tm6000_core *dev, u8 state) |
|
{ |
|
struct tm6000_IR *ir = dev->ir; |
|
|
|
if (!dev->ir) |
|
return; |
|
|
|
dprintk(2, "%s: %i\n",__func__, ir->wait); |
|
|
|
if (state) |
|
ir->wait = 1; |
|
else |
|
ir->wait = 0; |
|
} |
|
|
|
static int tm6000_ir_config(struct tm6000_IR *ir) |
|
{ |
|
struct tm6000_core *dev = ir->dev; |
|
u32 pulse = 0, leader = 0; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
|
|
/* |
|
* The IR decoder supports RC-5 or NEC, with a configurable timing. |
|
* The timing configuration there is not that accurate, as it uses |
|
* approximate values. The NEC spec mentions a 562.5 unit period, |
|
* and RC-5 uses a 888.8 period. |
|
* Currently, driver assumes a clock provided by a 12 MHz XTAL, but |
|
* a modprobe parameter can adjust it. |
|
* Adjustments are required for other timings. |
|
* It seems that the 900ms timing for NEC is used to detect a RC-5 |
|
* IR, in order to discard such decoding |
|
*/ |
|
|
|
switch (ir->rc_proto) { |
|
case RC_PROTO_BIT_NEC: |
|
leader = 900; /* ms */ |
|
pulse = 700; /* ms - the actual value would be 562 */ |
|
break; |
|
default: |
|
case RC_PROTO_BIT_RC5: |
|
leader = 900; /* ms - from the NEC decoding */ |
|
pulse = 1780; /* ms - The actual value would be 1776 */ |
|
break; |
|
} |
|
|
|
pulse = ir_clock_mhz * pulse; |
|
leader = ir_clock_mhz * leader; |
|
if (ir->rc_proto == RC_PROTO_BIT_NEC) |
|
leader = leader | 0x8000; |
|
|
|
dprintk(2, "%s: %s, %d MHz, leader = 0x%04x, pulse = 0x%06x \n", |
|
__func__, |
|
(ir->rc_proto == RC_PROTO_BIT_NEC) ? "NEC" : "RC-5", |
|
ir_clock_mhz, leader, pulse); |
|
|
|
/* Remote WAKEUP = enable, normal mode, from IR decoder output */ |
|
tm6000_set_reg(dev, TM6010_REQ07_RE5_REMOTE_WAKEUP, 0xfe); |
|
|
|
/* Enable IR reception on non-busrt mode */ |
|
tm6000_set_reg(dev, TM6010_REQ07_RD8_IR, 0x2f); |
|
|
|
/* IR_WKUP_SEL = Low byte in decoded IR data */ |
|
tm6000_set_reg(dev, TM6010_REQ07_RDA_IR_WAKEUP_SEL, 0xff); |
|
/* IR_WKU_ADD code */ |
|
tm6000_set_reg(dev, TM6010_REQ07_RDB_IR_WAKEUP_ADD, 0xff); |
|
|
|
tm6000_set_reg(dev, TM6010_REQ07_RDC_IR_LEADER1, leader >> 8); |
|
tm6000_set_reg(dev, TM6010_REQ07_RDD_IR_LEADER0, leader); |
|
|
|
tm6000_set_reg(dev, TM6010_REQ07_RDE_IR_PULSE_CNT1, pulse >> 8); |
|
tm6000_set_reg(dev, TM6010_REQ07_RDF_IR_PULSE_CNT0, pulse); |
|
|
|
if (!ir->polling) |
|
tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 0); |
|
else |
|
tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 1); |
|
msleep(10); |
|
|
|
/* Shows that IR is working via the LED */ |
|
tm6000_flash_led(dev, 0); |
|
msleep(100); |
|
tm6000_flash_led(dev, 1); |
|
ir->pwled = 1; |
|
|
|
return 0; |
|
} |
|
|
|
static void tm6000_ir_keydown(struct tm6000_IR *ir, |
|
const char *buf, unsigned int len) |
|
{ |
|
u8 device, command; |
|
u32 scancode; |
|
enum rc_proto protocol; |
|
|
|
if (len < 1) |
|
return; |
|
|
|
command = buf[0]; |
|
device = (len > 1 ? buf[1] : 0x0); |
|
switch (ir->rc_proto) { |
|
case RC_PROTO_BIT_RC5: |
|
protocol = RC_PROTO_RC5; |
|
scancode = RC_SCANCODE_RC5(device, command); |
|
break; |
|
case RC_PROTO_BIT_NEC: |
|
protocol = RC_PROTO_NEC; |
|
scancode = RC_SCANCODE_NEC(device, command); |
|
break; |
|
default: |
|
protocol = RC_PROTO_OTHER; |
|
scancode = RC_SCANCODE_OTHER(device << 8 | command); |
|
break; |
|
} |
|
|
|
dprintk(1, "%s, protocol: 0x%04x, scancode: 0x%08x\n", |
|
__func__, protocol, scancode); |
|
rc_keydown(ir->rc, protocol, scancode, 0); |
|
} |
|
|
|
static void tm6000_ir_urb_received(struct urb *urb) |
|
{ |
|
struct tm6000_core *dev = urb->context; |
|
struct tm6000_IR *ir = dev->ir; |
|
char *buf; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
if (urb->status < 0 || urb->actual_length <= 0) { |
|
printk(KERN_INFO "tm6000: IR URB failure: status: %i, length %i\n", |
|
urb->status, urb->actual_length); |
|
ir->submit_urb = 1; |
|
schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_SUBMIT_DELAY)); |
|
return; |
|
} |
|
buf = urb->transfer_buffer; |
|
|
|
if (ir_debug) |
|
print_hex_dump(KERN_DEBUG, "tm6000: IR data: ", |
|
DUMP_PREFIX_OFFSET,16, 1, |
|
buf, urb->actual_length, false); |
|
|
|
tm6000_ir_keydown(ir, urb->transfer_buffer, urb->actual_length); |
|
|
|
usb_submit_urb(urb, GFP_ATOMIC); |
|
/* |
|
* Flash the led. We can't do it here, as it is running on IRQ context. |
|
* So, use the scheduler to do it, in a few ms. |
|
*/ |
|
ir->pwled = 2; |
|
schedule_delayed_work(&ir->work, msecs_to_jiffies(10)); |
|
} |
|
|
|
static void tm6000_ir_handle_key(struct work_struct *work) |
|
{ |
|
struct tm6000_IR *ir = container_of(work, struct tm6000_IR, work.work); |
|
struct tm6000_core *dev = ir->dev; |
|
int rc; |
|
u8 buf[2]; |
|
|
|
if (ir->wait) |
|
return; |
|
|
|
dprintk(3, "%s\n",__func__); |
|
|
|
rc = tm6000_read_write_usb(dev, USB_DIR_IN | |
|
USB_TYPE_VENDOR | USB_RECIP_DEVICE, |
|
REQ_02_GET_IR_CODE, 0, 0, buf, 2); |
|
if (rc < 0) |
|
return; |
|
|
|
/* Check if something was read */ |
|
if ((buf[0] & 0xff) == 0xff) { |
|
if (!ir->pwled) { |
|
tm6000_flash_led(dev, 1); |
|
ir->pwled = 1; |
|
} |
|
return; |
|
} |
|
|
|
tm6000_ir_keydown(ir, buf, rc); |
|
tm6000_flash_led(dev, 0); |
|
ir->pwled = 0; |
|
|
|
/* Re-schedule polling */ |
|
schedule_delayed_work(&ir->work, msecs_to_jiffies(ir->polling)); |
|
} |
|
|
|
static void tm6000_ir_int_work(struct work_struct *work) |
|
{ |
|
struct tm6000_IR *ir = container_of(work, struct tm6000_IR, work.work); |
|
struct tm6000_core *dev = ir->dev; |
|
int rc; |
|
|
|
dprintk(3, "%s, submit_urb = %d, pwled = %d\n",__func__, ir->submit_urb, |
|
ir->pwled); |
|
|
|
if (ir->submit_urb) { |
|
dprintk(3, "Resubmit urb\n"); |
|
tm6000_set_reg(dev, REQ_04_EN_DISABLE_MCU_INT, 2, 0); |
|
|
|
rc = usb_submit_urb(ir->int_urb, GFP_ATOMIC); |
|
if (rc < 0) { |
|
printk(KERN_ERR "tm6000: Can't submit an IR interrupt. Error %i\n", |
|
rc); |
|
/* Retry in 100 ms */ |
|
schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_SUBMIT_DELAY)); |
|
return; |
|
} |
|
ir->submit_urb = 0; |
|
} |
|
|
|
/* Led is enabled only if USB submit doesn't fail */ |
|
if (ir->pwled == 2) { |
|
tm6000_flash_led(dev, 0); |
|
ir->pwled = 0; |
|
schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_INT_LED_DELAY)); |
|
} else if (!ir->pwled) { |
|
tm6000_flash_led(dev, 1); |
|
ir->pwled = 1; |
|
} |
|
} |
|
|
|
static int tm6000_ir_start(struct rc_dev *rc) |
|
{ |
|
struct tm6000_IR *ir = rc->priv; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
|
|
schedule_delayed_work(&ir->work, 0); |
|
|
|
return 0; |
|
} |
|
|
|
static void tm6000_ir_stop(struct rc_dev *rc) |
|
{ |
|
struct tm6000_IR *ir = rc->priv; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
|
|
cancel_delayed_work_sync(&ir->work); |
|
} |
|
|
|
static int tm6000_ir_change_protocol(struct rc_dev *rc, u64 *rc_proto) |
|
{ |
|
struct tm6000_IR *ir = rc->priv; |
|
|
|
if (!ir) |
|
return 0; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
|
|
ir->rc_proto = *rc_proto; |
|
|
|
tm6000_ir_config(ir); |
|
/* TODO */ |
|
return 0; |
|
} |
|
|
|
static int __tm6000_ir_int_start(struct rc_dev *rc) |
|
{ |
|
struct tm6000_IR *ir = rc->priv; |
|
struct tm6000_core *dev; |
|
int pipe, size; |
|
int err = -ENOMEM; |
|
|
|
if (!ir) |
|
return -ENODEV; |
|
dev = ir->dev; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
|
|
ir->int_urb = usb_alloc_urb(0, GFP_ATOMIC); |
|
if (!ir->int_urb) |
|
return -ENOMEM; |
|
|
|
pipe = usb_rcvintpipe(dev->udev, |
|
dev->int_in.endp->desc.bEndpointAddress |
|
& USB_ENDPOINT_NUMBER_MASK); |
|
|
|
size = usb_maxpacket(dev->udev, pipe, usb_pipeout(pipe)); |
|
dprintk(1, "IR max size: %d\n", size); |
|
|
|
ir->int_urb->transfer_buffer = kzalloc(size, GFP_ATOMIC); |
|
if (!ir->int_urb->transfer_buffer) { |
|
usb_free_urb(ir->int_urb); |
|
return err; |
|
} |
|
dprintk(1, "int interval: %d\n", dev->int_in.endp->desc.bInterval); |
|
|
|
usb_fill_int_urb(ir->int_urb, dev->udev, pipe, |
|
ir->int_urb->transfer_buffer, size, |
|
tm6000_ir_urb_received, dev, |
|
dev->int_in.endp->desc.bInterval); |
|
|
|
ir->submit_urb = 1; |
|
schedule_delayed_work(&ir->work, msecs_to_jiffies(URB_SUBMIT_DELAY)); |
|
|
|
return 0; |
|
} |
|
|
|
static void __tm6000_ir_int_stop(struct rc_dev *rc) |
|
{ |
|
struct tm6000_IR *ir = rc->priv; |
|
|
|
if (!ir || !ir->int_urb) |
|
return; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
|
|
usb_kill_urb(ir->int_urb); |
|
kfree(ir->int_urb->transfer_buffer); |
|
usb_free_urb(ir->int_urb); |
|
ir->int_urb = NULL; |
|
} |
|
|
|
int tm6000_ir_int_start(struct tm6000_core *dev) |
|
{ |
|
struct tm6000_IR *ir = dev->ir; |
|
|
|
if (!ir) |
|
return 0; |
|
|
|
return __tm6000_ir_int_start(ir->rc); |
|
} |
|
|
|
void tm6000_ir_int_stop(struct tm6000_core *dev) |
|
{ |
|
struct tm6000_IR *ir = dev->ir; |
|
|
|
if (!ir || !ir->rc) |
|
return; |
|
|
|
__tm6000_ir_int_stop(ir->rc); |
|
} |
|
|
|
int tm6000_ir_init(struct tm6000_core *dev) |
|
{ |
|
struct tm6000_IR *ir; |
|
struct rc_dev *rc; |
|
int err = -ENOMEM; |
|
u64 rc_proto; |
|
|
|
if (!enable_ir) |
|
return -ENODEV; |
|
|
|
if (!dev->caps.has_remote) |
|
return 0; |
|
|
|
if (!dev->ir_codes) |
|
return 0; |
|
|
|
ir = kzalloc(sizeof(*ir), GFP_ATOMIC); |
|
rc = rc_allocate_device(RC_DRIVER_SCANCODE); |
|
if (!ir || !rc) |
|
goto out; |
|
|
|
dprintk(2, "%s\n", __func__); |
|
|
|
/* record handles to ourself */ |
|
ir->dev = dev; |
|
dev->ir = ir; |
|
ir->rc = rc; |
|
|
|
/* input setup */ |
|
rc->allowed_protocols = RC_PROTO_BIT_RC5 | RC_PROTO_BIT_NEC; |
|
/* Needed, in order to support NEC remotes with 24 or 32 bits */ |
|
rc->scancode_mask = 0xffff; |
|
rc->priv = ir; |
|
rc->change_protocol = tm6000_ir_change_protocol; |
|
if (dev->int_in.endp) { |
|
rc->open = __tm6000_ir_int_start; |
|
rc->close = __tm6000_ir_int_stop; |
|
INIT_DELAYED_WORK(&ir->work, tm6000_ir_int_work); |
|
} else { |
|
rc->open = tm6000_ir_start; |
|
rc->close = tm6000_ir_stop; |
|
ir->polling = 50; |
|
INIT_DELAYED_WORK(&ir->work, tm6000_ir_handle_key); |
|
} |
|
|
|
snprintf(ir->name, sizeof(ir->name), "tm5600/60x0 IR (%s)", |
|
dev->name); |
|
|
|
usb_make_path(dev->udev, ir->phys, sizeof(ir->phys)); |
|
strlcat(ir->phys, "/input0", sizeof(ir->phys)); |
|
|
|
rc_proto = RC_PROTO_BIT_UNKNOWN; |
|
tm6000_ir_change_protocol(rc, &rc_proto); |
|
|
|
rc->device_name = ir->name; |
|
rc->input_phys = ir->phys; |
|
rc->input_id.bustype = BUS_USB; |
|
rc->input_id.version = 1; |
|
rc->input_id.vendor = le16_to_cpu(dev->udev->descriptor.idVendor); |
|
rc->input_id.product = le16_to_cpu(dev->udev->descriptor.idProduct); |
|
rc->map_name = dev->ir_codes; |
|
rc->driver_name = "tm6000"; |
|
rc->dev.parent = &dev->udev->dev; |
|
|
|
/* ir register */ |
|
err = rc_register_device(rc); |
|
if (err) |
|
goto out; |
|
|
|
return 0; |
|
|
|
out: |
|
dev->ir = NULL; |
|
rc_free_device(rc); |
|
kfree(ir); |
|
return err; |
|
} |
|
|
|
int tm6000_ir_fini(struct tm6000_core *dev) |
|
{ |
|
struct tm6000_IR *ir = dev->ir; |
|
|
|
/* skip detach on non attached board */ |
|
|
|
if (!ir) |
|
return 0; |
|
|
|
dprintk(2, "%s\n",__func__); |
|
|
|
if (!ir->polling) |
|
__tm6000_ir_int_stop(ir->rc); |
|
|
|
tm6000_ir_stop(ir->rc); |
|
|
|
/* Turn off the led */ |
|
tm6000_flash_led(dev, 0); |
|
ir->pwled = 0; |
|
|
|
rc_unregister_device(ir->rc); |
|
|
|
kfree(ir); |
|
dev->ir = NULL; |
|
|
|
return 0; |
|
}
|
|
|