forked from Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
632 lines
25 KiB
632 lines
25 KiB
#ifndef NETDEV_PCS_H |
|
#define NETDEV_PCS_H |
|
|
|
#include <linux/phy.h> |
|
#include <linux/spinlock.h> |
|
#include <linux/workqueue.h> |
|
|
|
struct device_node; |
|
struct ethtool_cmd; |
|
struct fwnode_handle; |
|
struct net_device; |
|
|
|
enum { |
|
MLO_PAUSE_NONE, |
|
MLO_PAUSE_RX = BIT(0), |
|
MLO_PAUSE_TX = BIT(1), |
|
MLO_PAUSE_TXRX_MASK = MLO_PAUSE_TX | MLO_PAUSE_RX, |
|
MLO_PAUSE_AN = BIT(2), |
|
|
|
MLO_AN_PHY = 0, /* Conventional PHY */ |
|
MLO_AN_FIXED, /* Fixed-link mode */ |
|
MLO_AN_INBAND, /* In-band protocol */ |
|
|
|
/* MAC_SYM_PAUSE and MAC_ASYM_PAUSE are used when configuring our |
|
* autonegotiation advertisement. They correspond to the PAUSE and |
|
* ASM_DIR bits defined by 802.3, respectively. |
|
* |
|
* The following table lists the values of tx_pause and rx_pause which |
|
* might be requested in mac_link_up. The exact values depend on either |
|
* the results of autonegotation (if MLO_PAUSE_AN is set) or user |
|
* configuration (if MLO_PAUSE_AN is not set). |
|
* |
|
* MAC_SYM_PAUSE MAC_ASYM_PAUSE MLO_PAUSE_AN tx_pause/rx_pause |
|
* ============= ============== ============ ================== |
|
* 0 0 0 0/0 |
|
* 0 0 1 0/0 |
|
* 0 1 0 0/0, 0/1, 1/0, 1/1 |
|
* 0 1 1 0/0, 1/0 |
|
* 1 0 0 0/0, 1/1 |
|
* 1 0 1 0/0, 1/1 |
|
* 1 1 0 0/0, 0/1, 1/0, 1/1 |
|
* 1 1 1 0/0, 0/1, 1/1 |
|
* |
|
* If you set MAC_ASYM_PAUSE, the user may request any combination of |
|
* tx_pause and rx_pause. You do not have to support these |
|
* combinations. |
|
* |
|
* However, you should support combinations of tx_pause and rx_pause |
|
* which might be the result of autonegotation. For example, don't set |
|
* MAC_SYM_PAUSE unless your device can support tx_pause and rx_pause |
|
* at the same time. |
|
*/ |
|
MAC_SYM_PAUSE = BIT(0), |
|
MAC_ASYM_PAUSE = BIT(1), |
|
MAC_10HD = BIT(2), |
|
MAC_10FD = BIT(3), |
|
MAC_10 = MAC_10HD | MAC_10FD, |
|
MAC_100HD = BIT(4), |
|
MAC_100FD = BIT(5), |
|
MAC_100 = MAC_100HD | MAC_100FD, |
|
MAC_1000HD = BIT(6), |
|
MAC_1000FD = BIT(7), |
|
MAC_1000 = MAC_1000HD | MAC_1000FD, |
|
MAC_2500FD = BIT(8), |
|
MAC_5000FD = BIT(9), |
|
MAC_10000FD = BIT(10), |
|
MAC_20000FD = BIT(11), |
|
MAC_25000FD = BIT(12), |
|
MAC_40000FD = BIT(13), |
|
MAC_50000FD = BIT(14), |
|
MAC_56000FD = BIT(15), |
|
MAC_100000FD = BIT(16), |
|
MAC_200000FD = BIT(17), |
|
MAC_400000FD = BIT(18), |
|
}; |
|
|
|
static inline bool phylink_autoneg_inband(unsigned int mode) |
|
{ |
|
return mode == MLO_AN_INBAND; |
|
} |
|
|
|
/** |
|
* struct phylink_link_state - link state structure |
|
* @advertising: ethtool bitmask containing advertised link modes |
|
* @lp_advertising: ethtool bitmask containing link partner advertised link |
|
* modes |
|
* @interface: link &typedef phy_interface_t mode |
|
* @speed: link speed, one of the SPEED_* constants. |
|
* @duplex: link duplex mode, one of DUPLEX_* constants. |
|
* @pause: link pause state, described by MLO_PAUSE_* constants. |
|
* @rate_matching: rate matching being performed, one of the RATE_MATCH_* |
|
* constants. If rate matching is taking place, then the speed/duplex of |
|
* the medium link mode (@speed and @duplex) and the speed/duplex of the phy |
|
* interface mode (@interface) are different. |
|
* @link: true if the link is up. |
|
* @an_enabled: true if autonegotiation is enabled/desired. |
|
* @an_complete: true if autonegotiation has completed. |
|
*/ |
|
struct phylink_link_state { |
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(advertising); |
|
__ETHTOOL_DECLARE_LINK_MODE_MASK(lp_advertising); |
|
phy_interface_t interface; |
|
int speed; |
|
int duplex; |
|
int pause; |
|
int rate_matching; |
|
unsigned int link:1; |
|
unsigned int an_enabled:1; |
|
unsigned int an_complete:1; |
|
}; |
|
|
|
enum phylink_op_type { |
|
PHYLINK_NETDEV = 0, |
|
PHYLINK_DEV, |
|
}; |
|
|
|
/** |
|
* struct phylink_config - PHYLINK configuration structure |
|
* @dev: a pointer to a struct device associated with the MAC |
|
* @type: operation type of PHYLINK instance |
|
* @legacy_pre_march2020: driver has not been updated for March 2020 updates |
|
* (See commit 7cceb599d15d ("net: phylink: avoid mac_config calls") |
|
* @poll_fixed_state: if true, starts link_poll, |
|
* if MAC link is at %MLO_AN_FIXED mode. |
|
* @mac_managed_pm: if true, indicate the MAC driver is responsible for PHY PM. |
|
* @ovr_an_inband: if true, override PCS to MLO_AN_INBAND |
|
* @get_fixed_state: callback to execute to determine the fixed link state, |
|
* if MAC link is at %MLO_AN_FIXED mode. |
|
* @supported_interfaces: bitmap describing which PHY_INTERFACE_MODE_xxx |
|
* are supported by the MAC/PCS. |
|
* @mac_capabilities: MAC pause/speed/duplex capabilities. |
|
*/ |
|
struct phylink_config { |
|
struct device *dev; |
|
enum phylink_op_type type; |
|
bool legacy_pre_march2020; |
|
bool poll_fixed_state; |
|
bool mac_managed_pm; |
|
bool ovr_an_inband; |
|
void (*get_fixed_state)(struct phylink_config *config, |
|
struct phylink_link_state *state); |
|
DECLARE_PHY_INTERFACE_MASK(supported_interfaces); |
|
unsigned long mac_capabilities; |
|
}; |
|
|
|
/** |
|
* struct phylink_mac_ops - MAC operations structure. |
|
* @validate: Validate and update the link configuration. |
|
* @mac_select_pcs: Select a PCS for the interface mode. |
|
* @mac_pcs_get_state: Read the current link state from the hardware. |
|
* @mac_prepare: prepare for a major reconfiguration of the interface. |
|
* @mac_config: configure the MAC for the selected mode and state. |
|
* @mac_finish: finish a major reconfiguration of the interface. |
|
* @mac_an_restart: restart 802.3z BaseX autonegotiation. |
|
* @mac_link_down: take the link down. |
|
* @mac_link_up: allow the link to come up. |
|
* |
|
* The individual methods are described more fully below. |
|
*/ |
|
struct phylink_mac_ops { |
|
void (*validate)(struct phylink_config *config, |
|
unsigned long *supported, |
|
struct phylink_link_state *state); |
|
struct phylink_pcs *(*mac_select_pcs)(struct phylink_config *config, |
|
phy_interface_t interface); |
|
void (*mac_pcs_get_state)(struct phylink_config *config, |
|
struct phylink_link_state *state); |
|
int (*mac_prepare)(struct phylink_config *config, unsigned int mode, |
|
phy_interface_t iface); |
|
void (*mac_config)(struct phylink_config *config, unsigned int mode, |
|
const struct phylink_link_state *state); |
|
int (*mac_finish)(struct phylink_config *config, unsigned int mode, |
|
phy_interface_t iface); |
|
void (*mac_an_restart)(struct phylink_config *config); |
|
void (*mac_link_down)(struct phylink_config *config, unsigned int mode, |
|
phy_interface_t interface); |
|
void (*mac_link_up)(struct phylink_config *config, |
|
struct phy_device *phy, unsigned int mode, |
|
phy_interface_t interface, int speed, int duplex, |
|
bool tx_pause, bool rx_pause); |
|
}; |
|
|
|
#if 0 /* For kernel-doc purposes only. */ |
|
/** |
|
* validate - Validate and update the link configuration |
|
* @config: a pointer to a &struct phylink_config. |
|
* @supported: ethtool bitmask for supported link modes. |
|
* @state: a pointer to a &struct phylink_link_state. |
|
* |
|
* Clear bits in the @supported and @state->advertising masks that |
|
* are not supportable by the MAC. |
|
* |
|
* Note that the PHY may be able to transform from one connection |
|
* technology to another, so, eg, don't clear 1000BaseX just |
|
* because the MAC is unable to BaseX mode. This is more about |
|
* clearing unsupported speeds and duplex settings. The port modes |
|
* should not be cleared; phylink_set_port_modes() will help with this. |
|
* |
|
* When @config->supported_interfaces has been set, phylink will iterate |
|
* over the supported interfaces to determine the full capability of the |
|
* MAC. The validation function must not print errors if @state->interface |
|
* is set to an unexpected value. |
|
* |
|
* When @config->supported_interfaces is empty, phylink will call this |
|
* function with @state->interface set to %PHY_INTERFACE_MODE_NA, and |
|
* expects the MAC driver to return all supported link modes. |
|
* |
|
* If the @state->interface mode is not supported, then the @supported |
|
* mask must be cleared. |
|
*/ |
|
void validate(struct phylink_config *config, unsigned long *supported, |
|
struct phylink_link_state *state); |
|
/** |
|
* mac_select_pcs: Select a PCS for the interface mode. |
|
* @config: a pointer to a &struct phylink_config. |
|
* @interface: PHY interface mode for PCS |
|
* |
|
* Return the &struct phylink_pcs for the specified interface mode, or |
|
* NULL if none is required, or an error pointer on error. |
|
* |
|
* This must not modify any state. It is used to query which PCS should |
|
* be used. Phylink will use this during validation to ensure that the |
|
* configuration is valid, and when setting a configuration to internally |
|
* set the PCS that will be used. |
|
*/ |
|
struct phylink_pcs *mac_select_pcs(struct phylink_config *config, |
|
phy_interface_t interface); |
|
|
|
/** |
|
* mac_pcs_get_state() - Read the current inband link state from the hardware |
|
* @config: a pointer to a &struct phylink_config. |
|
* @state: a pointer to a &struct phylink_link_state. |
|
* |
|
* Read the current inband link state from the MAC PCS, reporting the |
|
* current speed in @state->speed, duplex mode in @state->duplex, pause |
|
* mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits, |
|
* negotiation completion state in @state->an_complete, and link up state |
|
* in @state->link. If possible, @state->lp_advertising should also be |
|
* populated. |
|
* |
|
* Note: This is a legacy method. This function will not be called unless |
|
* legacy_pre_march2020 is set in &struct phylink_config and there is no |
|
* PCS attached. |
|
*/ |
|
void mac_pcs_get_state(struct phylink_config *config, |
|
struct phylink_link_state *state); |
|
|
|
/** |
|
* mac_prepare() - prepare to change the PHY interface mode |
|
* @config: a pointer to a &struct phylink_config. |
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. |
|
* @iface: interface mode to switch to |
|
* |
|
* phylink will call this method at the beginning of a full initialisation |
|
* of the link, which includes changing the interface mode or at initial |
|
* startup time. It may be called for the current mode. The MAC driver |
|
* should perform whatever actions are required, e.g. disabling the |
|
* Serdes PHY. |
|
* |
|
* This will be the first call in the sequence: |
|
* - mac_prepare() |
|
* - mac_config() |
|
* - pcs_config() |
|
* - possible pcs_an_restart() |
|
* - mac_finish() |
|
* |
|
* Returns zero on success, or negative errno on failure which will be |
|
* reported to the kernel log. |
|
*/ |
|
int mac_prepare(struct phylink_config *config, unsigned int mode, |
|
phy_interface_t iface); |
|
|
|
/** |
|
* mac_config() - configure the MAC for the selected mode and state |
|
* @config: a pointer to a &struct phylink_config. |
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. |
|
* @state: a pointer to a &struct phylink_link_state. |
|
* |
|
* Note - not all members of @state are valid. In particular, |
|
* @state->lp_advertising, @state->link, @state->an_complete are never |
|
* guaranteed to be correct, and so any mac_config() implementation must |
|
* never reference these fields. |
|
* |
|
* Note: For legacy March 2020 drivers (drivers with legacy_pre_march2020 set |
|
* in their &phylnk_config and which don't have a PCS), this function will be |
|
* called on each link up event, and to also change the in-band advert. For |
|
* non-legacy drivers, it will only be called to reconfigure the MAC for a |
|
* "major" change in e.g. interface mode. It will not be called for changes |
|
* in speed, duplex or pause modes or to change the in-band advertisement. |
|
* In any case, it is strongly preferred that speed, duplex and pause settings |
|
* are handled in the mac_link_up() method and not in this method. |
|
* |
|
* (this requires a rewrite - please refer to mac_link_up() for situations |
|
* where the PCS and MAC are not tightly integrated.) |
|
* |
|
* In all negotiation modes, as defined by @mode, @state->pause indicates the |
|
* pause settings which should be applied as follows. If %MLO_PAUSE_AN is not |
|
* set, %MLO_PAUSE_TX and %MLO_PAUSE_RX indicate whether the MAC should send |
|
* pause frames and/or act on received pause frames respectively. Otherwise, |
|
* the results of in-band negotiation/status from the MAC PCS should be used |
|
* to control the MAC pause mode settings. |
|
* |
|
* The action performed depends on the currently selected mode: |
|
* |
|
* %MLO_AN_FIXED, %MLO_AN_PHY: |
|
* Configure for non-inband negotiation mode, where the link settings |
|
* are completely communicated via mac_link_up(). The physical link |
|
* protocol from the MAC is specified by @state->interface. |
|
* |
|
* @state->advertising may be used, but is not required. |
|
* |
|
* Older drivers (prior to the mac_link_up() change) may use @state->speed, |
|
* @state->duplex and @state->pause to configure the MAC, but this is |
|
* deprecated; such drivers should be converted to use mac_link_up(). |
|
* |
|
* Other members of @state must be ignored. |
|
* |
|
* Valid state members: interface, advertising. |
|
* Deprecated state members: speed, duplex, pause. |
|
* |
|
* %MLO_AN_INBAND: |
|
* place the link in an inband negotiation mode (such as 802.3z |
|
* 1000base-X or Cisco SGMII mode depending on the @state->interface |
|
* mode). In both cases, link state management (whether the link |
|
* is up or not) is performed by the MAC, and reported via the |
|
* mac_pcs_get_state() callback. Changes in link state must be made |
|
* by calling phylink_mac_change(). |
|
* |
|
* Interface mode specific details are mentioned below. |
|
* |
|
* If in 802.3z mode, the link speed is fixed, dependent on the |
|
* @state->interface. Duplex and pause modes are negotiated via |
|
* the in-band configuration word. Advertised pause modes are set |
|
* according to the @state->an_enabled and @state->advertising |
|
* flags. Beware of MACs which only support full duplex at gigabit |
|
* and higher speeds. |
|
* |
|
* If in Cisco SGMII mode, the link speed and duplex mode are passed |
|
* in the serial bitstream 16-bit configuration word, and the MAC |
|
* should be configured to read these bits and acknowledge the |
|
* configuration word. Nothing is advertised by the MAC. The MAC is |
|
* responsible for reading the configuration word and configuring |
|
* itself accordingly. |
|
* |
|
* Valid state members: interface, an_enabled, pause, advertising. |
|
* |
|
* Implementations are expected to update the MAC to reflect the |
|
* requested settings - i.o.w., if nothing has changed between two |
|
* calls, no action is expected. If only flow control settings have |
|
* changed, flow control should be updated *without* taking the link |
|
* down. This "update" behaviour is critical to avoid bouncing the |
|
* link up status. |
|
*/ |
|
void mac_config(struct phylink_config *config, unsigned int mode, |
|
const struct phylink_link_state *state); |
|
|
|
/** |
|
* mac_finish() - finish a to change the PHY interface mode |
|
* @config: a pointer to a &struct phylink_config. |
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. |
|
* @iface: interface mode to switch to |
|
* |
|
* phylink will call this if it called mac_prepare() to allow the MAC to |
|
* complete any necessary steps after the MAC and PCS have been configured |
|
* for the @mode and @iface. E.g. a MAC driver may wish to re-enable the |
|
* Serdes PHY here if it was previously disabled by mac_prepare(). |
|
* |
|
* Returns zero on success, or negative errno on failure which will be |
|
* reported to the kernel log. |
|
*/ |
|
int mac_finish(struct phylink_config *config, unsigned int mode, |
|
phy_interface_t iface); |
|
|
|
/** |
|
* mac_an_restart() - restart 802.3z BaseX autonegotiation |
|
* @config: a pointer to a &struct phylink_config. |
|
* |
|
* Note: This is a legacy method. This function will not be called unless |
|
* legacy_pre_march2020 is set in &struct phylink_config and there is no |
|
* PCS attached. |
|
*/ |
|
void mac_an_restart(struct phylink_config *config); |
|
|
|
/** |
|
* mac_link_down() - take the link down |
|
* @config: a pointer to a &struct phylink_config. |
|
* @mode: link autonegotiation mode |
|
* @interface: link &typedef phy_interface_t mode |
|
* |
|
* If @mode is not an in-band negotiation mode (as defined by |
|
* phylink_autoneg_inband()), force the link down and disable any |
|
* Energy Efficient Ethernet MAC configuration. Interface type |
|
* selection must be done in mac_config(). |
|
*/ |
|
void mac_link_down(struct phylink_config *config, unsigned int mode, |
|
phy_interface_t interface); |
|
|
|
/** |
|
* mac_link_up() - allow the link to come up |
|
* @config: a pointer to a &struct phylink_config. |
|
* @phy: any attached phy |
|
* @mode: link autonegotiation mode |
|
* @interface: link &typedef phy_interface_t mode |
|
* @speed: link speed |
|
* @duplex: link duplex |
|
* @tx_pause: link transmit pause enablement status |
|
* @rx_pause: link receive pause enablement status |
|
* |
|
* Configure the MAC for an established link. |
|
* |
|
* @speed, @duplex, @tx_pause and @rx_pause indicate the finalised link |
|
* settings, and should be used to configure the MAC block appropriately |
|
* where these settings are not automatically conveyed from the PCS block, |
|
* or if in-band negotiation (as defined by phylink_autoneg_inband(@mode)) |
|
* is disabled. |
|
* |
|
* Note that when 802.3z in-band negotiation is in use, it is possible |
|
* that the user wishes to override the pause settings, and this should |
|
* be allowed when considering the implementation of this method. |
|
* |
|
* If in-band negotiation mode is disabled, allow the link to come up. If |
|
* @phy is non-%NULL, configure Energy Efficient Ethernet by calling |
|
* phy_init_eee() and perform appropriate MAC configuration for EEE. |
|
* Interface type selection must be done in mac_config(). |
|
*/ |
|
void mac_link_up(struct phylink_config *config, struct phy_device *phy, |
|
unsigned int mode, phy_interface_t interface, |
|
int speed, int duplex, bool tx_pause, bool rx_pause); |
|
#endif |
|
|
|
struct phylink_pcs_ops; |
|
|
|
/** |
|
* struct phylink_pcs - PHYLINK PCS instance |
|
* @ops: a pointer to the &struct phylink_pcs_ops structure |
|
* @poll: poll the PCS for link changes |
|
* |
|
* This structure is designed to be embedded within the PCS private data, |
|
* and will be passed between phylink and the PCS. |
|
*/ |
|
struct phylink_pcs { |
|
const struct phylink_pcs_ops *ops; |
|
bool poll; |
|
}; |
|
|
|
/** |
|
* struct phylink_pcs_ops - MAC PCS operations structure. |
|
* @pcs_validate: validate the link configuration. |
|
* @pcs_get_state: read the current MAC PCS link state from the hardware. |
|
* @pcs_config: configure the MAC PCS for the selected mode and state. |
|
* @pcs_an_restart: restart 802.3z BaseX autonegotiation. |
|
* @pcs_link_up: program the PCS for the resolved link configuration |
|
* (where necessary). |
|
*/ |
|
struct phylink_pcs_ops { |
|
int (*pcs_validate)(struct phylink_pcs *pcs, unsigned long *supported, |
|
const struct phylink_link_state *state); |
|
void (*pcs_get_state)(struct phylink_pcs *pcs, |
|
struct phylink_link_state *state); |
|
int (*pcs_config)(struct phylink_pcs *pcs, unsigned int mode, |
|
phy_interface_t interface, |
|
const unsigned long *advertising, |
|
bool permit_pause_to_mac); |
|
void (*pcs_an_restart)(struct phylink_pcs *pcs); |
|
void (*pcs_link_up)(struct phylink_pcs *pcs, unsigned int mode, |
|
phy_interface_t interface, int speed, int duplex); |
|
}; |
|
|
|
#if 0 /* For kernel-doc purposes only. */ |
|
/** |
|
* pcs_validate() - validate the link configuration. |
|
* @pcs: a pointer to a &struct phylink_pcs. |
|
* @supported: ethtool bitmask for supported link modes. |
|
* @state: a const pointer to a &struct phylink_link_state. |
|
* |
|
* Validate the interface mode, and advertising's autoneg bit, removing any |
|
* media ethtool link modes that would not be supportable from the supported |
|
* mask. Phylink will propagate the changes to the advertising mask. See the |
|
* &struct phylink_mac_ops validate() method. |
|
* |
|
* Returns -EINVAL if the interface mode/autoneg mode is not supported. |
|
* Returns non-zero positive if the link state can be supported. |
|
*/ |
|
int pcs_validate(struct phylink_pcs *pcs, unsigned long *supported, |
|
const struct phylink_link_state *state); |
|
|
|
/** |
|
* pcs_get_state() - Read the current inband link state from the hardware |
|
* @pcs: a pointer to a &struct phylink_pcs. |
|
* @state: a pointer to a &struct phylink_link_state. |
|
* |
|
* Read the current inband link state from the MAC PCS, reporting the |
|
* current speed in @state->speed, duplex mode in @state->duplex, pause |
|
* mode in @state->pause using the %MLO_PAUSE_RX and %MLO_PAUSE_TX bits, |
|
* negotiation completion state in @state->an_complete, and link up state |
|
* in @state->link. If possible, @state->lp_advertising should also be |
|
* populated. |
|
* |
|
* When present, this overrides mac_pcs_get_state() in &struct |
|
* phylink_mac_ops. |
|
*/ |
|
void pcs_get_state(struct phylink_pcs *pcs, |
|
struct phylink_link_state *state); |
|
|
|
/** |
|
* pcs_config() - Configure the PCS mode and advertisement |
|
* @pcs: a pointer to a &struct phylink_pcs. |
|
* @mode: one of %MLO_AN_FIXED, %MLO_AN_PHY, %MLO_AN_INBAND. |
|
* @interface: interface mode to be used |
|
* @advertising: adertisement ethtool link mode mask |
|
* @permit_pause_to_mac: permit forwarding pause resolution to MAC |
|
* |
|
* Configure the PCS for the operating mode, the interface mode, and set |
|
* the advertisement mask. @permit_pause_to_mac indicates whether the |
|
* hardware may forward the pause mode resolution to the MAC. |
|
* |
|
* When operating in %MLO_AN_INBAND, inband should always be enabled, |
|
* otherwise inband should be disabled. |
|
* |
|
* For SGMII, there is no advertisement from the MAC side, the PCS should |
|
* be programmed to acknowledge the inband word from the PHY. |
|
* |
|
* For 1000BASE-X, the advertisement should be programmed into the PCS. |
|
* |
|
* For most 10GBASE-R, there is no advertisement. |
|
*/ |
|
int pcs_config(struct phylink_pcs *pcs, unsigned int mode, |
|
phy_interface_t interface, const unsigned long *advertising, |
|
bool permit_pause_to_mac); |
|
|
|
/** |
|
* pcs_an_restart() - restart 802.3z BaseX autonegotiation |
|
* @pcs: a pointer to a &struct phylink_pcs. |
|
* |
|
* When PCS ops are present, this overrides mac_an_restart() in &struct |
|
* phylink_mac_ops. |
|
*/ |
|
void pcs_an_restart(struct phylink_pcs *pcs); |
|
|
|
/** |
|
* pcs_link_up() - program the PCS for the resolved link configuration |
|
* @pcs: a pointer to a &struct phylink_pcs. |
|
* @mode: link autonegotiation mode |
|
* @interface: link &typedef phy_interface_t mode |
|
* @speed: link speed |
|
* @duplex: link duplex |
|
* |
|
* This call will be made just before mac_link_up() to inform the PCS of |
|
* the resolved link parameters. For example, a PCS operating in SGMII |
|
* mode without in-band AN needs to be manually configured for the link |
|
* and duplex setting. Otherwise, this should be a no-op. |
|
*/ |
|
void pcs_link_up(struct phylink_pcs *pcs, unsigned int mode, |
|
phy_interface_t interface, int speed, int duplex); |
|
#endif |
|
|
|
void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps); |
|
unsigned long phylink_get_capabilities(phy_interface_t interface, |
|
unsigned long mac_capabilities, |
|
int rate_matching); |
|
void phylink_generic_validate(struct phylink_config *config, |
|
unsigned long *supported, |
|
struct phylink_link_state *state); |
|
|
|
struct phylink *phylink_create(struct phylink_config *, struct fwnode_handle *, |
|
phy_interface_t iface, |
|
const struct phylink_mac_ops *mac_ops); |
|
void phylink_destroy(struct phylink *); |
|
|
|
int phylink_connect_phy(struct phylink *, struct phy_device *); |
|
int phylink_of_phy_connect(struct phylink *, struct device_node *, u32 flags); |
|
int phylink_fwnode_phy_connect(struct phylink *pl, |
|
struct fwnode_handle *fwnode, |
|
u32 flags); |
|
void phylink_disconnect_phy(struct phylink *); |
|
|
|
void phylink_mac_change(struct phylink *, bool up); |
|
|
|
void phylink_start(struct phylink *); |
|
void phylink_stop(struct phylink *); |
|
|
|
void phylink_suspend(struct phylink *pl, bool mac_wol); |
|
void phylink_resume(struct phylink *pl); |
|
|
|
void phylink_ethtool_get_wol(struct phylink *, struct ethtool_wolinfo *); |
|
int phylink_ethtool_set_wol(struct phylink *, struct ethtool_wolinfo *); |
|
|
|
int phylink_ethtool_ksettings_get(struct phylink *, |
|
struct ethtool_link_ksettings *); |
|
int phylink_ethtool_ksettings_set(struct phylink *, |
|
const struct ethtool_link_ksettings *); |
|
int phylink_ethtool_nway_reset(struct phylink *); |
|
void phylink_ethtool_get_pauseparam(struct phylink *, |
|
struct ethtool_pauseparam *); |
|
int phylink_ethtool_set_pauseparam(struct phylink *, |
|
struct ethtool_pauseparam *); |
|
int phylink_get_eee_err(struct phylink *); |
|
int phylink_init_eee(struct phylink *, bool); |
|
int phylink_ethtool_get_eee(struct phylink *, struct ethtool_eee *); |
|
int phylink_ethtool_set_eee(struct phylink *, struct ethtool_eee *); |
|
int phylink_mii_ioctl(struct phylink *, struct ifreq *, int); |
|
int phylink_speed_down(struct phylink *pl, bool sync); |
|
int phylink_speed_up(struct phylink *pl); |
|
|
|
#define phylink_zero(bm) \ |
|
bitmap_zero(bm, __ETHTOOL_LINK_MODE_MASK_NBITS) |
|
#define __phylink_do_bit(op, bm, mode) \ |
|
op(ETHTOOL_LINK_MODE_ ## mode ## _BIT, bm) |
|
|
|
#define phylink_set(bm, mode) __phylink_do_bit(__set_bit, bm, mode) |
|
#define phylink_clear(bm, mode) __phylink_do_bit(__clear_bit, bm, mode) |
|
#define phylink_test(bm, mode) __phylink_do_bit(test_bit, bm, mode) |
|
|
|
void phylink_set_port_modes(unsigned long *bits); |
|
|
|
void phylink_mii_c22_pcs_decode_state(struct phylink_link_state *state, |
|
u16 bmsr, u16 lpa); |
|
void phylink_mii_c22_pcs_get_state(struct mdio_device *pcs, |
|
struct phylink_link_state *state); |
|
int phylink_mii_c22_pcs_encode_advertisement(phy_interface_t interface, |
|
const unsigned long *advertising); |
|
int phylink_mii_c22_pcs_config(struct mdio_device *pcs, unsigned int mode, |
|
phy_interface_t interface, |
|
const unsigned long *advertising); |
|
void phylink_mii_c22_pcs_an_restart(struct mdio_device *pcs); |
|
|
|
void phylink_mii_c45_pcs_get_state(struct mdio_device *pcs, |
|
struct phylink_link_state *state); |
|
|
|
void phylink_decode_usxgmii_word(struct phylink_link_state *state, |
|
uint16_t lpa); |
|
#endif
|
|
|