mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
132 lines
3.2 KiB
132 lines
3.2 KiB
// SPDX-License-Identifier: GPL-2.0 |
|
/* |
|
* ALPHAPROJECT AP-SH4AD-0A Support. |
|
* |
|
* Copyright (C) 2010 ALPHAPROJECT Co.,Ltd. |
|
* Copyright (C) 2010 Matt Fleming |
|
* Copyright (C) 2010 Paul Mundt |
|
*/ |
|
#include <linux/init.h> |
|
#include <linux/platform_device.h> |
|
#include <linux/io.h> |
|
#include <linux/regulator/fixed.h> |
|
#include <linux/regulator/machine.h> |
|
#include <linux/smsc911x.h> |
|
#include <linux/irq.h> |
|
#include <linux/clk.h> |
|
#include <asm/machvec.h> |
|
#include <linux/sizes.h> |
|
|
|
/* Dummy supplies, where voltage doesn't matter */ |
|
static struct regulator_consumer_supply dummy_supplies[] = { |
|
REGULATOR_SUPPLY("vddvario", "smsc911x"), |
|
REGULATOR_SUPPLY("vdd33a", "smsc911x"), |
|
}; |
|
|
|
static struct resource smsc911x_resources[] = { |
|
[0] = { |
|
.name = "smsc911x-memory", |
|
.start = 0xA4000000, |
|
.end = 0xA4000000 + SZ_256 - 1, |
|
.flags = IORESOURCE_MEM, |
|
}, |
|
[1] = { |
|
.name = "smsc911x-irq", |
|
.start = evt2irq(0x200), |
|
.end = evt2irq(0x200), |
|
.flags = IORESOURCE_IRQ, |
|
}, |
|
}; |
|
|
|
static struct smsc911x_platform_config smsc911x_config = { |
|
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, |
|
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, |
|
.flags = SMSC911X_USE_16BIT, |
|
.phy_interface = PHY_INTERFACE_MODE_MII, |
|
}; |
|
|
|
static struct platform_device smsc911x_device = { |
|
.name = "smsc911x", |
|
.id = -1, |
|
.num_resources = ARRAY_SIZE(smsc911x_resources), |
|
.resource = smsc911x_resources, |
|
.dev = { |
|
.platform_data = &smsc911x_config, |
|
}, |
|
}; |
|
|
|
static struct platform_device *apsh4ad0a_devices[] __initdata = { |
|
&smsc911x_device, |
|
}; |
|
|
|
static int __init apsh4ad0a_devices_setup(void) |
|
{ |
|
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies)); |
|
|
|
return platform_add_devices(apsh4ad0a_devices, |
|
ARRAY_SIZE(apsh4ad0a_devices)); |
|
} |
|
device_initcall(apsh4ad0a_devices_setup); |
|
|
|
static int apsh4ad0a_mode_pins(void) |
|
{ |
|
int value = 0; |
|
|
|
/* These are the factory default settings of SW1 and SW2. |
|
* If you change these dip switches then you will need to |
|
* adjust the values below as well. |
|
*/ |
|
value |= MODE_PIN0; /* Clock Mode 3 */ |
|
value |= MODE_PIN1; |
|
value &= ~MODE_PIN2; |
|
value &= ~MODE_PIN3; |
|
value &= ~MODE_PIN4; /* 16-bit Area0 bus width */ |
|
value |= MODE_PIN5; |
|
value |= MODE_PIN6; |
|
value |= MODE_PIN7; /* Normal mode */ |
|
value |= MODE_PIN8; /* Little Endian */ |
|
value |= MODE_PIN9; /* Crystal resonator */ |
|
value &= ~MODE_PIN10; /* 29-bit address mode */ |
|
value &= ~MODE_PIN11; /* PCI-E Root port */ |
|
value &= ~MODE_PIN12; /* 4 lane + 1 lane */ |
|
value |= MODE_PIN13; /* AUD Enable */ |
|
value &= ~MODE_PIN14; /* Normal Operation */ |
|
|
|
return value; |
|
} |
|
|
|
static int apsh4ad0a_clk_init(void) |
|
{ |
|
struct clk *clk; |
|
int ret; |
|
|
|
clk = clk_get(NULL, "extal"); |
|
if (IS_ERR(clk)) |
|
return PTR_ERR(clk); |
|
ret = clk_set_rate(clk, 33333000); |
|
clk_put(clk); |
|
|
|
return ret; |
|
} |
|
|
|
/* Initialize the board */ |
|
static void __init apsh4ad0a_setup(char **cmdline_p) |
|
{ |
|
pr_info("Alpha Project AP-SH4AD-0A support:\n"); |
|
} |
|
|
|
static void __init apsh4ad0a_init_irq(void) |
|
{ |
|
plat_irq_setup_pins(IRQ_MODE_IRQ3210); |
|
} |
|
|
|
/* |
|
* The Machine Vector |
|
*/ |
|
static struct sh_machine_vector mv_apsh4ad0a __initmv = { |
|
.mv_name = "AP-SH4AD-0A", |
|
.mv_setup = apsh4ad0a_setup, |
|
.mv_mode_pins = apsh4ad0a_mode_pins, |
|
.mv_clk_init = apsh4ad0a_clk_init, |
|
.mv_init_irq = apsh4ad0a_init_irq, |
|
};
|
|
|