mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
194 lines
6.7 KiB
194 lines
6.7 KiB
Maxim MAX77693 multi-function device |
|
|
|
MAX77693 is a Multifunction device with the following submodules: |
|
- PMIC, |
|
- CHARGER, |
|
- LED, |
|
- MUIC, |
|
- HAPTIC |
|
|
|
It is interfaced to host controller using i2c. |
|
This document describes the bindings for the mfd device. |
|
|
|
Required properties: |
|
- compatible : Must be "maxim,max77693". |
|
- reg : Specifies the i2c slave address of PMIC block. |
|
- interrupts : This i2c device has an IRQ line connected to the main SoC. |
|
|
|
Optional properties: |
|
- regulators : The regulators of max77693 have to be instantiated under subnode |
|
named "regulators" using the following format. |
|
|
|
regulators { |
|
regulator-compatible = ESAFEOUT1/ESAFEOUT2/CHARGER |
|
standard regulator constraints[*]. |
|
}; |
|
|
|
[*] refer Documentation/devicetree/bindings/regulator/regulator.txt |
|
|
|
- haptic : The MAX77693 haptic device utilises a PWM controlled motor to provide |
|
users with tactile feedback. PWM period and duty-cycle are varied in |
|
order to provide the appropriate level of feedback. |
|
|
|
Required properties: |
|
- compatible : Must be "maxim,max77693-haptic" |
|
- haptic-supply : power supply for the haptic motor |
|
[*] refer Documentation/devicetree/bindings/regulator/regulator.txt |
|
- pwms : phandle to the physical PWM(Pulse Width Modulation) device. |
|
PWM properties should be named "pwms". And number of cell is different |
|
for each pwm device. |
|
To get more information, please refer to documentation. |
|
[*] refer Documentation/devicetree/bindings/pwm/pwm.txt |
|
|
|
- charger : Node configuring the charger driver. |
|
If present, required properties: |
|
- compatible : Must be "maxim,max77693-charger". |
|
|
|
Optional properties (if not set, defaults will be used): |
|
- maxim,constant-microvolt : Battery constant voltage in uV. The charger |
|
will operate in fast charge constant current mode till battery voltage |
|
reaches this level. Then the charger will switch to fast charge constant |
|
voltage mode. Also vsys (system voltage) will be set to this value when |
|
DC power is supplied but charger is not enabled. |
|
Valid values: 3650000 - 4400000, step by 25000 (rounded down) |
|
Default: 4200000 |
|
|
|
- maxim,min-system-microvolt : Minimal system voltage in uV. |
|
Valid values: 3000000 - 3700000, step by 100000 (rounded down) |
|
Default: 3600000 |
|
|
|
- maxim,thermal-regulation-celsius : Temperature in Celsius for entering |
|
high temperature charging mode. If die temperature exceeds this value |
|
the charging current will be reduced by 105 mA/Celsius. |
|
Valid values: 70, 85, 100, 115 |
|
Default: 100 |
|
|
|
- maxim,battery-overcurrent-microamp : Overcurrent protection threshold |
|
in uA (current from battery to system). |
|
Valid values: 2000000 - 3500000, step by 250000 (rounded down) |
|
Default: 3500000 |
|
|
|
- maxim,charge-input-threshold-microvolt : Threshold voltage in uV for |
|
triggering input voltage regulation loop. If input voltage decreases |
|
below this value, the input current will be reduced to reach the |
|
threshold voltage. |
|
Valid values: 4300000, 4700000, 4800000, 4900000 |
|
Default: 4300000 |
|
|
|
- led : the LED submodule device node |
|
|
|
There are two LED outputs available - FLED1 and FLED2. Each of them can |
|
control a separate LED or they can be connected together to double |
|
the maximum current for a single connected LED. One LED is represented |
|
by one child node. |
|
|
|
Required properties: |
|
- compatible : Must be "maxim,max77693-led". |
|
|
|
Optional properties: |
|
- maxim,boost-mode : |
|
In boost mode the device can produce up to 1.2A of total current |
|
on both outputs. The maximum current on each output is reduced |
|
to 625mA then. If not enabled explicitly, boost setting defaults to |
|
LEDS_BOOST_FIXED in case both current sources are used. |
|
Possible values: |
|
LEDS_BOOST_OFF (0) - no boost, |
|
LEDS_BOOST_ADAPTIVE (1) - adaptive mode, |
|
LEDS_BOOST_FIXED (2) - fixed mode. |
|
- maxim,boost-mvout : Output voltage of the boost module in millivolts. |
|
Valid values: 3300 - 5500, step by 25 (rounded down) |
|
Default: 3300 |
|
- maxim,mvsys-min : Low input voltage level in millivolts. Flash is not fired |
|
if chip estimates that system voltage could drop below this level due |
|
to flash power consumption. |
|
Valid values: 2400 - 3400, step by 33 (rounded down) |
|
Default: 2400 |
|
|
|
Required properties for the LED child node: |
|
- led-sources : see Documentation/devicetree/bindings/leds/common.txt; |
|
device current output identifiers: 0 - FLED1, 1 - FLED2 |
|
- led-max-microamp : see Documentation/devicetree/bindings/leds/common.txt |
|
Valid values for a LED connected to one FLED output: |
|
15625 - 250000, step by 15625 (rounded down) |
|
Valid values for a LED connected to both FLED outputs: |
|
15625 - 500000, step by 15625 (rounded down) |
|
- flash-max-microamp : see Documentation/devicetree/bindings/leds/common.txt |
|
Valid values for a single LED connected to one FLED output |
|
(boost mode must be turned off): |
|
15625 - 1000000, step by 15625 (rounded down) |
|
Valid values for a single LED connected to both FLED outputs: |
|
15625 - 1250000, step by 15625 (rounded down) |
|
Valid values for two LEDs case: |
|
15625 - 625000, step by 15625 (rounded down) |
|
- flash-max-timeout-us : see Documentation/devicetree/bindings/leds/common.txt |
|
Valid values: 62500 - 1000000, step by 62500 (rounded down) |
|
|
|
Optional properties for the LED child node: |
|
- label : see Documentation/devicetree/bindings/leds/common.txt |
|
|
|
Optional nodes: |
|
- max77693-muic : |
|
Node used only by extcon consumers. |
|
Required properties: |
|
- compatible : "maxim,max77693-muic" |
|
|
|
Example: |
|
#include <dt-bindings/leds/common.h> |
|
|
|
max77693@66 { |
|
compatible = "maxim,max77693"; |
|
reg = <0x66>; |
|
interrupt-parent = <&gpx1>; |
|
interrupts = <5 2>; |
|
|
|
regulators { |
|
esafeout@1 { |
|
regulator-compatible = "ESAFEOUT1"; |
|
regulator-name = "ESAFEOUT1"; |
|
regulator-boot-on; |
|
}; |
|
esafeout@2 { |
|
regulator-compatible = "ESAFEOUT2"; |
|
regulator-name = "ESAFEOUT2"; |
|
}; |
|
charger@0 { |
|
regulator-compatible = "CHARGER"; |
|
regulator-name = "CHARGER"; |
|
regulator-min-microamp = <60000>; |
|
regulator-max-microamp = <2580000>; |
|
regulator-boot-on; |
|
}; |
|
}; |
|
|
|
haptic { |
|
compatible = "maxim,max77693-haptic"; |
|
haptic-supply = <&haptic_supply>; |
|
pwms = <&pwm 0 40000 0>; |
|
pwm-names = "haptic"; |
|
}; |
|
|
|
charger { |
|
compatible = "maxim,max77693-charger"; |
|
|
|
maxim,constant-microvolt = <4200000>; |
|
maxim,min-system-microvolt = <3600000>; |
|
maxim,thermal-regulation-celsius = <75>; |
|
maxim,battery-overcurrent-microamp = <3000000>; |
|
maxim,charge-input-threshold-microvolt = <4300000>; |
|
}; |
|
|
|
led { |
|
compatible = "maxim,max77693-led"; |
|
maxim,boost-mode = <LEDS_BOOST_FIXED>; |
|
maxim,boost-mvout = <5000>; |
|
maxim,mvsys-min = <2400>; |
|
|
|
camera_flash: flash-led { |
|
label = "max77693-flash"; |
|
led-sources = <0>, <1>; |
|
led-max-microamp = <500000>; |
|
flash-max-microamp = <1250000>; |
|
flash-max-timeout-us = <1000000>; |
|
}; |
|
}; |
|
};
|
|
|