mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
107 lines
4.5 KiB
107 lines
4.5 KiB
Device-Tree bindings for Samsung SoC display controller (FIMD) |
|
|
|
FIMD (Fully Interactive Mobile Display) is the Display Controller for the |
|
Samsung series of SoCs which transfers the image data from a video memory |
|
buffer to an external LCD interface. |
|
|
|
Required properties: |
|
- compatible: value should be one of the following |
|
"samsung,s3c2443-fimd"; /* for S3C24XX SoCs */ |
|
"samsung,s3c6400-fimd"; /* for S3C64XX SoCs */ |
|
"samsung,s5pv210-fimd"; /* for S5PV210 SoC */ |
|
"samsung,exynos3250-fimd"; /* for Exynos3250/3472 SoCs */ |
|
"samsung,exynos4210-fimd"; /* for Exynos4 SoCs */ |
|
"samsung,exynos5250-fimd"; /* for Exynos5250 SoCs */ |
|
"samsung,exynos5420-fimd"; /* for Exynos5420/5422/5800 SoCs */ |
|
|
|
- reg: physical base address and length of the FIMD registers set. |
|
|
|
- interrupts: should contain a list of all FIMD IP block interrupts in the |
|
order: FIFO Level, VSYNC, LCD_SYSTEM. The interrupt specifier |
|
format depends on the interrupt controller used. |
|
|
|
- interrupt-names: should contain the interrupt names: "fifo", "vsync", |
|
"lcd_sys", in the same order as they were listed in the interrupts |
|
property. |
|
|
|
- pinctrl-0: pin control group to be used for this controller. |
|
|
|
- pinctrl-names: must contain a "default" entry. |
|
|
|
- clocks: must include clock specifiers corresponding to entries in the |
|
clock-names property. |
|
|
|
- clock-names: list of clock names sorted in the same order as the clocks |
|
property. Must contain "sclk_fimd" and "fimd". |
|
|
|
Optional Properties: |
|
- power-domains: a phandle to FIMD power domain node. |
|
- samsung,invert-vden: video enable signal is inverted |
|
- samsung,invert-vclk: video clock signal is inverted |
|
- display-timings: timing settings for FIMD, as described in document [1]. |
|
Can be used in case timings cannot be provided otherwise |
|
or to override timings provided by the panel. |
|
- samsung,sysreg: handle to syscon used to control the system registers |
|
- i80-if-timings: timing configuration for lcd i80 interface support. |
|
- cs-setup: clock cycles for the active period of address signal is enabled |
|
until chip select is enabled. |
|
If not specified, the default value(0) will be used. |
|
- wr-setup: clock cycles for the active period of CS signal is enabled until |
|
write signal is enabled. |
|
If not specified, the default value(0) will be used. |
|
- wr-active: clock cycles for the active period of CS is enabled. |
|
If not specified, the default value(1) will be used. |
|
- wr-hold: clock cycles for the active period of CS is disabled until write |
|
signal is disabled. |
|
If not specified, the default value(0) will be used. |
|
|
|
The parameters are defined as: |
|
|
|
VCLK(internal) __|??????|_____|??????|_____|??????|_____|??????|_____|?? |
|
: : : : : |
|
Address Output --:<XXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XXXXXXXXXXXX:XX |
|
| cs-setup+1 | : : : |
|
|<---------->| : : : |
|
Chip Select ???????????????|____________:____________:____________|?? |
|
| wr-setup+1 | | wr-hold+1 | |
|
|<---------->| |<---------->| |
|
Write Enable ????????????????????????????|____________|??????????????? |
|
| wr-active+1| |
|
|<---------->| |
|
Video Data ----------------------------<XXXXXXXXXXXXXXXXXXXXXXXXX>-- |
|
|
|
The device node can contain 'port' child nodes according to the bindings defined |
|
in [2]. The following are properties specific to those nodes: |
|
- reg: (required) port index, can be: |
|
0 - for CAMIF0 input, |
|
1 - for CAMIF1 input, |
|
2 - for CAMIF2 input, |
|
3 - for parallel output, |
|
4 - for write-back interface |
|
|
|
[1]: Documentation/devicetree/bindings/display/panel/display-timing.txt |
|
[2]: Documentation/devicetree/bindings/media/video-interfaces.txt |
|
|
|
Example: |
|
|
|
SoC specific DT entry: |
|
|
|
fimd@11c00000 { |
|
compatible = "samsung,exynos4210-fimd"; |
|
interrupt-parent = <&combiner>; |
|
reg = <0x11c00000 0x20000>; |
|
interrupt-names = "fifo", "vsync", "lcd_sys"; |
|
interrupts = <11 0>, <11 1>, <11 2>; |
|
clocks = <&clock 140>, <&clock 283>; |
|
clock-names = "sclk_fimd", "fimd"; |
|
power-domains = <&pd_lcd0>; |
|
status = "disabled"; |
|
}; |
|
|
|
Board specific DT entry: |
|
|
|
fimd@11c00000 { |
|
pinctrl-0 = <&lcd_clk &lcd_data24 &pwm1_out>; |
|
pinctrl-names = "default"; |
|
status = "okay"; |
|
};
|
|
|