mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
1655 lines
43 KiB
1655 lines
43 KiB
// SPDX-License-Identifier: GPL-2.0-or-later |
|
/* |
|
* Driver for Samsung S5K6AAFX SXGA 1/6" 1.3M CMOS Image Sensor |
|
* with embedded SoC ISP. |
|
* |
|
* Copyright (C) 2011, Samsung Electronics Co., Ltd. |
|
* Sylwester Nawrocki <[email protected]> |
|
* |
|
* Based on a driver authored by Dongsoo Nathaniel Kim. |
|
* Copyright (C) 2009, Dongsoo Nathaniel Kim <[email protected]> |
|
*/ |
|
|
|
#include <linux/clk.h> |
|
#include <linux/delay.h> |
|
#include <linux/gpio.h> |
|
#include <linux/i2c.h> |
|
#include <linux/media.h> |
|
#include <linux/module.h> |
|
#include <linux/regulator/consumer.h> |
|
#include <linux/slab.h> |
|
|
|
#include <media/media-entity.h> |
|
#include <media/v4l2-ctrls.h> |
|
#include <media/v4l2-device.h> |
|
#include <media/v4l2-subdev.h> |
|
#include <media/v4l2-mediabus.h> |
|
#include <media/i2c/s5k6aa.h> |
|
|
|
static int debug; |
|
module_param(debug, int, 0644); |
|
|
|
#define DRIVER_NAME "S5K6AA" |
|
|
|
/* The token to indicate array termination */ |
|
#define S5K6AA_TERM 0xffff |
|
#define S5K6AA_OUT_WIDTH_DEF 640 |
|
#define S5K6AA_OUT_HEIGHT_DEF 480 |
|
#define S5K6AA_WIN_WIDTH_MAX 1280 |
|
#define S5K6AA_WIN_HEIGHT_MAX 1024 |
|
#define S5K6AA_WIN_WIDTH_MIN 8 |
|
#define S5K6AA_WIN_HEIGHT_MIN 8 |
|
|
|
/* |
|
* H/W register Interface (0xD0000000 - 0xD0000FFF) |
|
*/ |
|
#define AHB_MSB_ADDR_PTR 0xfcfc |
|
#define GEN_REG_OFFSH 0xd000 |
|
#define REG_CMDWR_ADDRH 0x0028 |
|
#define REG_CMDWR_ADDRL 0x002a |
|
#define REG_CMDRD_ADDRH 0x002c |
|
#define REG_CMDRD_ADDRL 0x002e |
|
#define REG_CMDBUF0_ADDR 0x0f12 |
|
#define REG_CMDBUF1_ADDR 0x0f10 |
|
|
|
/* |
|
* Host S/W Register interface (0x70000000 - 0x70002000) |
|
* The value of the two most significant address bytes is 0x7000, |
|
* (HOST_SWIF_OFFS_H). The register addresses below specify 2 LSBs. |
|
*/ |
|
#define HOST_SWIF_OFFSH 0x7000 |
|
|
|
/* Initialization parameters */ |
|
/* Master clock frequency in KHz */ |
|
#define REG_I_INCLK_FREQ_L 0x01b8 |
|
#define REG_I_INCLK_FREQ_H 0x01ba |
|
#define MIN_MCLK_FREQ_KHZ 6000U |
|
#define MAX_MCLK_FREQ_KHZ 27000U |
|
#define REG_I_USE_NPVI_CLOCKS 0x01c6 |
|
#define REG_I_USE_NMIPI_CLOCKS 0x01c8 |
|
|
|
/* Clock configurations, n = 0..2. REG_I_* frequency unit is 4 kHz. */ |
|
#define REG_I_OPCLK_4KHZ(n) ((n) * 6 + 0x01cc) |
|
#define REG_I_MIN_OUTRATE_4KHZ(n) ((n) * 6 + 0x01ce) |
|
#define REG_I_MAX_OUTRATE_4KHZ(n) ((n) * 6 + 0x01d0) |
|
#define SYS_PLL_OUT_FREQ (48000000 / 4000) |
|
#define PCLK_FREQ_MIN (24000000 / 4000) |
|
#define PCLK_FREQ_MAX (48000000 / 4000) |
|
#define REG_I_INIT_PARAMS_UPDATED 0x01e0 |
|
#define REG_I_ERROR_INFO 0x01e2 |
|
|
|
/* General purpose parameters */ |
|
#define REG_USER_BRIGHTNESS 0x01e4 |
|
#define REG_USER_CONTRAST 0x01e6 |
|
#define REG_USER_SATURATION 0x01e8 |
|
#define REG_USER_SHARPBLUR 0x01ea |
|
|
|
#define REG_G_SPEC_EFFECTS 0x01ee |
|
#define REG_G_ENABLE_PREV 0x01f0 |
|
#define REG_G_ENABLE_PREV_CHG 0x01f2 |
|
#define REG_G_NEW_CFG_SYNC 0x01f8 |
|
#define REG_G_PREVZOOM_IN_WIDTH 0x020a |
|
#define REG_G_PREVZOOM_IN_HEIGHT 0x020c |
|
#define REG_G_PREVZOOM_IN_XOFFS 0x020e |
|
#define REG_G_PREVZOOM_IN_YOFFS 0x0210 |
|
#define REG_G_INPUTS_CHANGE_REQ 0x021a |
|
#define REG_G_ACTIVE_PREV_CFG 0x021c |
|
#define REG_G_PREV_CFG_CHG 0x021e |
|
#define REG_G_PREV_OPEN_AFTER_CH 0x0220 |
|
#define REG_G_PREV_CFG_ERROR 0x0222 |
|
|
|
/* Preview control section. n = 0...4. */ |
|
#define PREG(n, x) ((n) * 0x26 + x) |
|
#define REG_P_OUT_WIDTH(n) PREG(n, 0x0242) |
|
#define REG_P_OUT_HEIGHT(n) PREG(n, 0x0244) |
|
#define REG_P_FMT(n) PREG(n, 0x0246) |
|
#define REG_P_MAX_OUT_RATE(n) PREG(n, 0x0248) |
|
#define REG_P_MIN_OUT_RATE(n) PREG(n, 0x024a) |
|
#define REG_P_PVI_MASK(n) PREG(n, 0x024c) |
|
#define REG_P_CLK_INDEX(n) PREG(n, 0x024e) |
|
#define REG_P_FR_RATE_TYPE(n) PREG(n, 0x0250) |
|
#define FR_RATE_DYNAMIC 0 |
|
#define FR_RATE_FIXED 1 |
|
#define FR_RATE_FIXED_ACCURATE 2 |
|
#define REG_P_FR_RATE_Q_TYPE(n) PREG(n, 0x0252) |
|
#define FR_RATE_Q_BEST_FRRATE 1 /* Binning enabled */ |
|
#define FR_RATE_Q_BEST_QUALITY 2 /* Binning disabled */ |
|
/* Frame period in 0.1 ms units */ |
|
#define REG_P_MAX_FR_TIME(n) PREG(n, 0x0254) |
|
#define REG_P_MIN_FR_TIME(n) PREG(n, 0x0256) |
|
/* Conversion to REG_P_[MAX/MIN]_FR_TIME value; __t: time in us */ |
|
#define US_TO_FR_TIME(__t) ((__t) / 100) |
|
#define S5K6AA_MIN_FR_TIME 33300 /* us */ |
|
#define S5K6AA_MAX_FR_TIME 650000 /* us */ |
|
#define S5K6AA_MAX_HIGHRES_FR_TIME 666 /* x100 us */ |
|
/* The below 5 registers are for "device correction" values */ |
|
#define REG_P_COLORTEMP(n) PREG(n, 0x025e) |
|
#define REG_P_PREV_MIRROR(n) PREG(n, 0x0262) |
|
|
|
/* Extended image property controls */ |
|
/* Exposure time in 10 us units */ |
|
#define REG_SF_USR_EXPOSURE_L 0x03c6 |
|
#define REG_SF_USR_EXPOSURE_H 0x03c8 |
|
#define REG_SF_USR_EXPOSURE_CHG 0x03ca |
|
#define REG_SF_USR_TOT_GAIN 0x03cc |
|
#define REG_SF_USR_TOT_GAIN_CHG 0x03ce |
|
#define REG_SF_RGAIN 0x03d0 |
|
#define REG_SF_RGAIN_CHG 0x03d2 |
|
#define REG_SF_GGAIN 0x03d4 |
|
#define REG_SF_GGAIN_CHG 0x03d6 |
|
#define REG_SF_BGAIN 0x03d8 |
|
#define REG_SF_BGAIN_CHG 0x03da |
|
#define REG_SF_FLICKER_QUANT 0x03dc |
|
#define REG_SF_FLICKER_QUANT_CHG 0x03de |
|
|
|
/* Output interface (parallel/MIPI) setup */ |
|
#define REG_OIF_EN_MIPI_LANES 0x03fa |
|
#define REG_OIF_EN_PACKETS 0x03fc |
|
#define REG_OIF_CFG_CHG 0x03fe |
|
|
|
/* Auto-algorithms enable mask */ |
|
#define REG_DBG_AUTOALG_EN 0x0400 |
|
#define AALG_ALL_EN_MASK (1 << 0) |
|
#define AALG_AE_EN_MASK (1 << 1) |
|
#define AALG_DIVLEI_EN_MASK (1 << 2) |
|
#define AALG_WB_EN_MASK (1 << 3) |
|
#define AALG_FLICKER_EN_MASK (1 << 5) |
|
#define AALG_FIT_EN_MASK (1 << 6) |
|
#define AALG_WRHW_EN_MASK (1 << 7) |
|
|
|
/* Firmware revision information */ |
|
#define REG_FW_APIVER 0x012e |
|
#define S5K6AAFX_FW_APIVER 0x0001 |
|
#define REG_FW_REVISION 0x0130 |
|
|
|
/* For now we use only one user configuration register set */ |
|
#define S5K6AA_MAX_PRESETS 1 |
|
|
|
static const char * const s5k6aa_supply_names[] = { |
|
"vdd_core", /* Digital core supply 1.5V (1.4V to 1.6V) */ |
|
"vdda", /* Analog power supply 2.8V (2.6V to 3.0V) */ |
|
"vdd_reg", /* Regulator input power 1.8V (1.7V to 1.9V) |
|
or 2.8V (2.6V to 3.0) */ |
|
"vddio", /* I/O supply 1.8V (1.65V to 1.95V) |
|
or 2.8V (2.5V to 3.1V) */ |
|
}; |
|
#define S5K6AA_NUM_SUPPLIES ARRAY_SIZE(s5k6aa_supply_names) |
|
|
|
enum s5k6aa_gpio_id { |
|
STBY, |
|
RSET, |
|
GPIO_NUM, |
|
}; |
|
|
|
struct s5k6aa_regval { |
|
u16 addr; |
|
u16 val; |
|
}; |
|
|
|
struct s5k6aa_pixfmt { |
|
u32 code; |
|
u32 colorspace; |
|
/* REG_P_FMT(x) register value */ |
|
u16 reg_p_fmt; |
|
}; |
|
|
|
struct s5k6aa_preset { |
|
/* output pixel format and resolution */ |
|
struct v4l2_mbus_framefmt mbus_fmt; |
|
u8 clk_id; |
|
u8 index; |
|
}; |
|
|
|
struct s5k6aa_ctrls { |
|
struct v4l2_ctrl_handler handler; |
|
/* Auto / manual white balance cluster */ |
|
struct v4l2_ctrl *awb; |
|
struct v4l2_ctrl *gain_red; |
|
struct v4l2_ctrl *gain_blue; |
|
struct v4l2_ctrl *gain_green; |
|
/* Mirror cluster */ |
|
struct v4l2_ctrl *hflip; |
|
struct v4l2_ctrl *vflip; |
|
/* Auto exposure / manual exposure and gain cluster */ |
|
struct v4l2_ctrl *auto_exp; |
|
struct v4l2_ctrl *exposure; |
|
struct v4l2_ctrl *gain; |
|
}; |
|
|
|
struct s5k6aa_interval { |
|
u16 reg_fr_time; |
|
struct v4l2_fract interval; |
|
/* Maximum rectangle for the interval */ |
|
struct v4l2_frmsize_discrete size; |
|
}; |
|
|
|
struct s5k6aa { |
|
struct v4l2_subdev sd; |
|
struct media_pad pad; |
|
|
|
enum v4l2_mbus_type bus_type; |
|
u8 mipi_lanes; |
|
|
|
int (*s_power)(int enable); |
|
struct regulator_bulk_data supplies[S5K6AA_NUM_SUPPLIES]; |
|
struct s5k6aa_gpio gpio[GPIO_NUM]; |
|
|
|
/* external master clock frequency */ |
|
unsigned long mclk_frequency; |
|
/* ISP internal master clock frequency */ |
|
u16 clk_fop; |
|
/* output pixel clock frequency range */ |
|
u16 pclk_fmin; |
|
u16 pclk_fmax; |
|
|
|
unsigned int inv_hflip:1; |
|
unsigned int inv_vflip:1; |
|
|
|
/* protects the struct members below */ |
|
struct mutex lock; |
|
|
|
/* sensor matrix scan window */ |
|
struct v4l2_rect ccd_rect; |
|
|
|
struct s5k6aa_ctrls ctrls; |
|
struct s5k6aa_preset presets[S5K6AA_MAX_PRESETS]; |
|
struct s5k6aa_preset *preset; |
|
const struct s5k6aa_interval *fiv; |
|
|
|
unsigned int streaming:1; |
|
unsigned int apply_cfg:1; |
|
unsigned int apply_crop:1; |
|
unsigned int power; |
|
}; |
|
|
|
static struct s5k6aa_regval s5k6aa_analog_config[] = { |
|
/* Analog settings */ |
|
{ 0x112a, 0x0000 }, { 0x1132, 0x0000 }, |
|
{ 0x113e, 0x0000 }, { 0x115c, 0x0000 }, |
|
{ 0x1164, 0x0000 }, { 0x1174, 0x0000 }, |
|
{ 0x1178, 0x0000 }, { 0x077a, 0x0000 }, |
|
{ 0x077c, 0x0000 }, { 0x077e, 0x0000 }, |
|
{ 0x0780, 0x0000 }, { 0x0782, 0x0000 }, |
|
{ 0x0784, 0x0000 }, { 0x0786, 0x0000 }, |
|
{ 0x0788, 0x0000 }, { 0x07a2, 0x0000 }, |
|
{ 0x07a4, 0x0000 }, { 0x07a6, 0x0000 }, |
|
{ 0x07a8, 0x0000 }, { 0x07b6, 0x0000 }, |
|
{ 0x07b8, 0x0002 }, { 0x07ba, 0x0004 }, |
|
{ 0x07bc, 0x0004 }, { 0x07be, 0x0005 }, |
|
{ 0x07c0, 0x0005 }, { S5K6AA_TERM, 0 }, |
|
}; |
|
|
|
/* TODO: Add RGB888 and Bayer format */ |
|
static const struct s5k6aa_pixfmt s5k6aa_formats[] = { |
|
{ MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_JPEG, 5 }, |
|
/* range 16-240 */ |
|
{ MEDIA_BUS_FMT_YUYV8_2X8, V4L2_COLORSPACE_REC709, 6 }, |
|
{ MEDIA_BUS_FMT_RGB565_2X8_BE, V4L2_COLORSPACE_JPEG, 0 }, |
|
}; |
|
|
|
static const struct s5k6aa_interval s5k6aa_intervals[] = { |
|
{ 1000, {10000, 1000000}, {1280, 1024} }, /* 10 fps */ |
|
{ 666, {15000, 1000000}, {1280, 1024} }, /* 15 fps */ |
|
{ 500, {20000, 1000000}, {1280, 720} }, /* 20 fps */ |
|
{ 400, {25000, 1000000}, {640, 480} }, /* 25 fps */ |
|
{ 333, {33300, 1000000}, {640, 480} }, /* 30 fps */ |
|
}; |
|
|
|
#define S5K6AA_INTERVAL_DEF_INDEX 1 /* 15 fps */ |
|
|
|
static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl) |
|
{ |
|
return &container_of(ctrl->handler, struct s5k6aa, ctrls.handler)->sd; |
|
} |
|
|
|
static inline struct s5k6aa *to_s5k6aa(struct v4l2_subdev *sd) |
|
{ |
|
return container_of(sd, struct s5k6aa, sd); |
|
} |
|
|
|
/* Set initial values for all preview presets */ |
|
static void s5k6aa_presets_data_init(struct s5k6aa *s5k6aa) |
|
{ |
|
struct s5k6aa_preset *preset = &s5k6aa->presets[0]; |
|
int i; |
|
|
|
for (i = 0; i < S5K6AA_MAX_PRESETS; i++) { |
|
preset->mbus_fmt.width = S5K6AA_OUT_WIDTH_DEF; |
|
preset->mbus_fmt.height = S5K6AA_OUT_HEIGHT_DEF; |
|
preset->mbus_fmt.code = s5k6aa_formats[0].code; |
|
preset->index = i; |
|
preset->clk_id = 0; |
|
preset++; |
|
} |
|
|
|
s5k6aa->fiv = &s5k6aa_intervals[S5K6AA_INTERVAL_DEF_INDEX]; |
|
s5k6aa->preset = &s5k6aa->presets[0]; |
|
} |
|
|
|
static int s5k6aa_i2c_read(struct i2c_client *client, u16 addr, u16 *val) |
|
{ |
|
u8 wbuf[2] = {addr >> 8, addr & 0xFF}; |
|
struct i2c_msg msg[2]; |
|
u8 rbuf[2]; |
|
int ret; |
|
|
|
msg[0].addr = client->addr; |
|
msg[0].flags = 0; |
|
msg[0].len = 2; |
|
msg[0].buf = wbuf; |
|
|
|
msg[1].addr = client->addr; |
|
msg[1].flags = I2C_M_RD; |
|
msg[1].len = 2; |
|
msg[1].buf = rbuf; |
|
|
|
ret = i2c_transfer(client->adapter, msg, 2); |
|
*val = be16_to_cpu(*((__be16 *)rbuf)); |
|
|
|
v4l2_dbg(3, debug, client, "i2c_read: 0x%04X : 0x%04x\n", addr, *val); |
|
|
|
return ret == 2 ? 0 : ret; |
|
} |
|
|
|
static int s5k6aa_i2c_write(struct i2c_client *client, u16 addr, u16 val) |
|
{ |
|
u8 buf[4] = {addr >> 8, addr & 0xFF, val >> 8, val & 0xFF}; |
|
|
|
int ret = i2c_master_send(client, buf, 4); |
|
v4l2_dbg(3, debug, client, "i2c_write: 0x%04X : 0x%04x\n", addr, val); |
|
|
|
return ret == 4 ? 0 : ret; |
|
} |
|
|
|
/* The command register write, assumes Command_Wr_addH = 0x7000. */ |
|
static int s5k6aa_write(struct i2c_client *c, u16 addr, u16 val) |
|
{ |
|
int ret = s5k6aa_i2c_write(c, REG_CMDWR_ADDRL, addr); |
|
if (ret) |
|
return ret; |
|
return s5k6aa_i2c_write(c, REG_CMDBUF0_ADDR, val); |
|
} |
|
|
|
/* The command register read, assumes Command_Rd_addH = 0x7000. */ |
|
static int s5k6aa_read(struct i2c_client *client, u16 addr, u16 *val) |
|
{ |
|
int ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRL, addr); |
|
if (ret) |
|
return ret; |
|
return s5k6aa_i2c_read(client, REG_CMDBUF0_ADDR, val); |
|
} |
|
|
|
static int s5k6aa_write_array(struct v4l2_subdev *sd, |
|
const struct s5k6aa_regval *msg) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(sd); |
|
u16 addr_incr = 0; |
|
int ret = 0; |
|
|
|
while (msg->addr != S5K6AA_TERM) { |
|
if (addr_incr != 2) |
|
ret = s5k6aa_i2c_write(client, REG_CMDWR_ADDRL, |
|
msg->addr); |
|
if (ret) |
|
break; |
|
ret = s5k6aa_i2c_write(client, REG_CMDBUF0_ADDR, msg->val); |
|
if (ret) |
|
break; |
|
/* Assume that msg->addr is always less than 0xfffc */ |
|
addr_incr = (msg + 1)->addr - msg->addr; |
|
msg++; |
|
} |
|
|
|
return ret; |
|
} |
|
|
|
/* Configure the AHB high address bytes for GTG registers access */ |
|
static int s5k6aa_set_ahb_address(struct i2c_client *client) |
|
{ |
|
int ret = s5k6aa_i2c_write(client, AHB_MSB_ADDR_PTR, GEN_REG_OFFSH); |
|
if (ret) |
|
return ret; |
|
ret = s5k6aa_i2c_write(client, REG_CMDRD_ADDRH, HOST_SWIF_OFFSH); |
|
if (ret) |
|
return ret; |
|
return s5k6aa_i2c_write(client, REG_CMDWR_ADDRH, HOST_SWIF_OFFSH); |
|
} |
|
|
|
/** |
|
* s5k6aa_configure_pixel_clocks - apply ISP main clock/PLL configuration |
|
* @s5k6aa: pointer to &struct s5k6aa describing the device |
|
* |
|
* Configure the internal ISP PLL for the required output frequency. |
|
* Locking: called with s5k6aa.lock mutex held. |
|
*/ |
|
static int s5k6aa_configure_pixel_clocks(struct s5k6aa *s5k6aa) |
|
{ |
|
struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); |
|
unsigned long fmclk = s5k6aa->mclk_frequency / 1000; |
|
u16 status; |
|
int ret; |
|
|
|
if (WARN(fmclk < MIN_MCLK_FREQ_KHZ || fmclk > MAX_MCLK_FREQ_KHZ, |
|
"Invalid clock frequency: %ld\n", fmclk)) |
|
return -EINVAL; |
|
|
|
s5k6aa->pclk_fmin = PCLK_FREQ_MIN; |
|
s5k6aa->pclk_fmax = PCLK_FREQ_MAX; |
|
s5k6aa->clk_fop = SYS_PLL_OUT_FREQ; |
|
|
|
/* External input clock frequency in kHz */ |
|
ret = s5k6aa_write(c, REG_I_INCLK_FREQ_H, fmclk >> 16); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_I_INCLK_FREQ_L, fmclk & 0xFFFF); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_I_USE_NPVI_CLOCKS, 1); |
|
/* Internal PLL frequency */ |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_I_OPCLK_4KHZ(0), s5k6aa->clk_fop); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_I_MIN_OUTRATE_4KHZ(0), |
|
s5k6aa->pclk_fmin); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_I_MAX_OUTRATE_4KHZ(0), |
|
s5k6aa->pclk_fmax); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_I_INIT_PARAMS_UPDATED, 1); |
|
if (!ret) |
|
ret = s5k6aa_read(c, REG_I_ERROR_INFO, &status); |
|
|
|
return ret ? ret : (status ? -EINVAL : 0); |
|
} |
|
|
|
/* Set horizontal and vertical image flipping */ |
|
static int s5k6aa_set_mirror(struct s5k6aa *s5k6aa, int horiz_flip) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
int index = s5k6aa->preset->index; |
|
|
|
unsigned int vflip = s5k6aa->ctrls.vflip->val ^ s5k6aa->inv_vflip; |
|
unsigned int flip = (horiz_flip ^ s5k6aa->inv_hflip) | (vflip << 1); |
|
|
|
return s5k6aa_write(client, REG_P_PREV_MIRROR(index), flip); |
|
} |
|
|
|
/* Configure auto/manual white balance and R/G/B gains */ |
|
static int s5k6aa_set_awb(struct s5k6aa *s5k6aa, int awb) |
|
{ |
|
struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); |
|
struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls; |
|
u16 reg; |
|
|
|
int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, ®); |
|
|
|
if (!ret && !awb) { |
|
ret = s5k6aa_write(c, REG_SF_RGAIN, ctrls->gain_red->val); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_SF_RGAIN_CHG, 1); |
|
if (ret) |
|
return ret; |
|
|
|
ret = s5k6aa_write(c, REG_SF_GGAIN, ctrls->gain_green->val); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_SF_GGAIN_CHG, 1); |
|
if (ret) |
|
return ret; |
|
|
|
ret = s5k6aa_write(c, REG_SF_BGAIN, ctrls->gain_blue->val); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_SF_BGAIN_CHG, 1); |
|
} |
|
if (!ret) { |
|
reg = awb ? reg | AALG_WB_EN_MASK : reg & ~AALG_WB_EN_MASK; |
|
ret = s5k6aa_write(c, REG_DBG_AUTOALG_EN, reg); |
|
} |
|
|
|
return ret; |
|
} |
|
|
|
/* Program FW with exposure time, 'exposure' in us units */ |
|
static int s5k6aa_set_user_exposure(struct i2c_client *client, int exposure) |
|
{ |
|
unsigned int time = exposure / 10; |
|
|
|
int ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_L, time & 0xffff); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_SF_USR_EXPOSURE_H, time >> 16); |
|
if (ret) |
|
return ret; |
|
return s5k6aa_write(client, REG_SF_USR_EXPOSURE_CHG, 1); |
|
} |
|
|
|
static int s5k6aa_set_user_gain(struct i2c_client *client, int gain) |
|
{ |
|
int ret = s5k6aa_write(client, REG_SF_USR_TOT_GAIN, gain); |
|
if (ret) |
|
return ret; |
|
return s5k6aa_write(client, REG_SF_USR_TOT_GAIN_CHG, 1); |
|
} |
|
|
|
/* Set auto/manual exposure and total gain */ |
|
static int s5k6aa_set_auto_exposure(struct s5k6aa *s5k6aa, int value) |
|
{ |
|
struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); |
|
unsigned int exp_time = s5k6aa->ctrls.exposure->val; |
|
u16 auto_alg; |
|
|
|
int ret = s5k6aa_read(c, REG_DBG_AUTOALG_EN, &auto_alg); |
|
if (ret) |
|
return ret; |
|
|
|
v4l2_dbg(1, debug, c, "man_exp: %d, auto_exp: %d, a_alg: 0x%x\n", |
|
exp_time, value, auto_alg); |
|
|
|
if (value == V4L2_EXPOSURE_AUTO) { |
|
auto_alg |= AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK; |
|
} else { |
|
ret = s5k6aa_set_user_exposure(c, exp_time); |
|
if (ret) |
|
return ret; |
|
ret = s5k6aa_set_user_gain(c, s5k6aa->ctrls.gain->val); |
|
if (ret) |
|
return ret; |
|
auto_alg &= ~(AALG_AE_EN_MASK | AALG_DIVLEI_EN_MASK); |
|
} |
|
|
|
return s5k6aa_write(c, REG_DBG_AUTOALG_EN, auto_alg); |
|
} |
|
|
|
static int s5k6aa_set_anti_flicker(struct s5k6aa *s5k6aa, int value) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
u16 auto_alg; |
|
int ret; |
|
|
|
ret = s5k6aa_read(client, REG_DBG_AUTOALG_EN, &auto_alg); |
|
if (ret) |
|
return ret; |
|
|
|
if (value == V4L2_CID_POWER_LINE_FREQUENCY_AUTO) { |
|
auto_alg |= AALG_FLICKER_EN_MASK; |
|
} else { |
|
auto_alg &= ~AALG_FLICKER_EN_MASK; |
|
/* The V4L2_CID_LINE_FREQUENCY control values match |
|
* the register values */ |
|
ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT, value); |
|
if (ret) |
|
return ret; |
|
ret = s5k6aa_write(client, REG_SF_FLICKER_QUANT_CHG, 1); |
|
if (ret) |
|
return ret; |
|
} |
|
|
|
return s5k6aa_write(client, REG_DBG_AUTOALG_EN, auto_alg); |
|
} |
|
|
|
static int s5k6aa_set_colorfx(struct s5k6aa *s5k6aa, int val) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
static const struct v4l2_control colorfx[] = { |
|
{ V4L2_COLORFX_NONE, 0 }, |
|
{ V4L2_COLORFX_BW, 1 }, |
|
{ V4L2_COLORFX_NEGATIVE, 2 }, |
|
{ V4L2_COLORFX_SEPIA, 3 }, |
|
{ V4L2_COLORFX_SKY_BLUE, 4 }, |
|
{ V4L2_COLORFX_SKETCH, 5 }, |
|
}; |
|
int i; |
|
|
|
for (i = 0; i < ARRAY_SIZE(colorfx); i++) { |
|
if (colorfx[i].id == val) |
|
return s5k6aa_write(client, REG_G_SPEC_EFFECTS, |
|
colorfx[i].value); |
|
} |
|
return -EINVAL; |
|
} |
|
|
|
static int s5k6aa_preview_config_status(struct i2c_client *client) |
|
{ |
|
u16 error = 0; |
|
int ret = s5k6aa_read(client, REG_G_PREV_CFG_ERROR, &error); |
|
|
|
v4l2_dbg(1, debug, client, "error: 0x%x (%d)\n", error, ret); |
|
return ret ? ret : (error ? -EINVAL : 0); |
|
} |
|
|
|
static int s5k6aa_get_pixfmt_index(struct s5k6aa *s5k6aa, |
|
struct v4l2_mbus_framefmt *mf) |
|
{ |
|
unsigned int i; |
|
|
|
for (i = 0; i < ARRAY_SIZE(s5k6aa_formats); i++) |
|
if (mf->colorspace == s5k6aa_formats[i].colorspace && |
|
mf->code == s5k6aa_formats[i].code) |
|
return i; |
|
return 0; |
|
} |
|
|
|
static int s5k6aa_set_output_framefmt(struct s5k6aa *s5k6aa, |
|
struct s5k6aa_preset *preset) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
int fmt_index = s5k6aa_get_pixfmt_index(s5k6aa, &preset->mbus_fmt); |
|
int ret; |
|
|
|
ret = s5k6aa_write(client, REG_P_OUT_WIDTH(preset->index), |
|
preset->mbus_fmt.width); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_OUT_HEIGHT(preset->index), |
|
preset->mbus_fmt.height); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_FMT(preset->index), |
|
s5k6aa_formats[fmt_index].reg_p_fmt); |
|
return ret; |
|
} |
|
|
|
static int s5k6aa_set_input_params(struct s5k6aa *s5k6aa) |
|
{ |
|
struct i2c_client *c = v4l2_get_subdevdata(&s5k6aa->sd); |
|
struct v4l2_rect *r = &s5k6aa->ccd_rect; |
|
int ret; |
|
|
|
ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_WIDTH, r->width); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_HEIGHT, r->height); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_XOFFS, r->left); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_G_PREVZOOM_IN_YOFFS, r->top); |
|
if (!ret) |
|
ret = s5k6aa_write(c, REG_G_INPUTS_CHANGE_REQ, 1); |
|
if (!ret) |
|
s5k6aa->apply_crop = 0; |
|
|
|
return ret; |
|
} |
|
|
|
/** |
|
* s5k6aa_configure_video_bus - configure the video output interface |
|
* @s5k6aa: pointer to &struct s5k6aa describing the device |
|
* @bus_type: video bus type: parallel or MIPI-CSI |
|
* @nlanes: number of MIPI lanes to be used (MIPI-CSI only) |
|
* |
|
* Note: Only parallel bus operation has been tested. |
|
*/ |
|
static int s5k6aa_configure_video_bus(struct s5k6aa *s5k6aa, |
|
enum v4l2_mbus_type bus_type, int nlanes) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
u16 cfg = 0; |
|
int ret; |
|
|
|
/* |
|
* TODO: The sensor is supposed to support BT.601 and BT.656 |
|
* but there is nothing indicating how to switch between both |
|
* in the datasheet. For now default BT.601 interface is assumed. |
|
*/ |
|
if (bus_type == V4L2_MBUS_CSI2_DPHY) |
|
cfg = nlanes; |
|
else if (bus_type != V4L2_MBUS_PARALLEL) |
|
return -EINVAL; |
|
|
|
ret = s5k6aa_write(client, REG_OIF_EN_MIPI_LANES, cfg); |
|
if (ret) |
|
return ret; |
|
return s5k6aa_write(client, REG_OIF_CFG_CHG, 1); |
|
} |
|
|
|
/* This function should be called when switching to new user configuration set*/ |
|
static int s5k6aa_new_config_sync(struct i2c_client *client, int timeout, |
|
int cid) |
|
{ |
|
unsigned long end = jiffies + msecs_to_jiffies(timeout); |
|
u16 reg = 1; |
|
int ret; |
|
|
|
ret = s5k6aa_write(client, REG_G_ACTIVE_PREV_CFG, cid); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_G_NEW_CFG_SYNC, 1); |
|
if (timeout == 0) |
|
return ret; |
|
|
|
while (ret >= 0 && time_is_after_jiffies(end)) { |
|
ret = s5k6aa_read(client, REG_G_NEW_CFG_SYNC, ®); |
|
if (!reg) |
|
return 0; |
|
usleep_range(1000, 5000); |
|
} |
|
return ret ? ret : -ETIMEDOUT; |
|
} |
|
|
|
/** |
|
* s5k6aa_set_prev_config - write user preview register set |
|
* @s5k6aa: pointer to &struct s5k6aa describing the device |
|
* @preset: s5kaa preset to be applied |
|
* |
|
* Configure output resolution and color format, pixel clock |
|
* frequency range, device frame rate type and frame period range. |
|
*/ |
|
static int s5k6aa_set_prev_config(struct s5k6aa *s5k6aa, |
|
struct s5k6aa_preset *preset) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
int idx = preset->index; |
|
u16 frame_rate_q; |
|
int ret; |
|
|
|
if (s5k6aa->fiv->reg_fr_time >= S5K6AA_MAX_HIGHRES_FR_TIME) |
|
frame_rate_q = FR_RATE_Q_BEST_FRRATE; |
|
else |
|
frame_rate_q = FR_RATE_Q_BEST_QUALITY; |
|
|
|
ret = s5k6aa_set_output_framefmt(s5k6aa, preset); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_MAX_OUT_RATE(idx), |
|
s5k6aa->pclk_fmax); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_MIN_OUT_RATE(idx), |
|
s5k6aa->pclk_fmin); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_CLK_INDEX(idx), |
|
preset->clk_id); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_FR_RATE_TYPE(idx), |
|
FR_RATE_DYNAMIC); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_FR_RATE_Q_TYPE(idx), |
|
frame_rate_q); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_MAX_FR_TIME(idx), |
|
s5k6aa->fiv->reg_fr_time + 33); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_P_MIN_FR_TIME(idx), |
|
s5k6aa->fiv->reg_fr_time - 33); |
|
if (!ret) |
|
ret = s5k6aa_new_config_sync(client, 250, idx); |
|
if (!ret) |
|
ret = s5k6aa_preview_config_status(client); |
|
if (!ret) |
|
s5k6aa->apply_cfg = 0; |
|
|
|
v4l2_dbg(1, debug, client, "Frame interval: %d +/- 3.3ms. (%d)\n", |
|
s5k6aa->fiv->reg_fr_time, ret); |
|
return ret; |
|
} |
|
|
|
/** |
|
* s5k6aa_initialize_isp - basic ISP MCU initialization |
|
* @sd: pointer to V4L2 sub-device descriptor |
|
* |
|
* Configure AHB addresses for registers read/write; configure PLLs for |
|
* required output pixel clock. The ISP power supply needs to be already |
|
* enabled, with an optional H/W reset. |
|
* Locking: called with s5k6aa.lock mutex held. |
|
*/ |
|
static int s5k6aa_initialize_isp(struct v4l2_subdev *sd) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(sd); |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
int ret; |
|
|
|
s5k6aa->apply_crop = 1; |
|
s5k6aa->apply_cfg = 1; |
|
msleep(100); |
|
|
|
ret = s5k6aa_set_ahb_address(client); |
|
if (ret) |
|
return ret; |
|
ret = s5k6aa_configure_video_bus(s5k6aa, s5k6aa->bus_type, |
|
s5k6aa->mipi_lanes); |
|
if (ret) |
|
return ret; |
|
ret = s5k6aa_write_array(sd, s5k6aa_analog_config); |
|
if (ret) |
|
return ret; |
|
msleep(20); |
|
|
|
return s5k6aa_configure_pixel_clocks(s5k6aa); |
|
} |
|
|
|
static int s5k6aa_gpio_set_value(struct s5k6aa *priv, int id, u32 val) |
|
{ |
|
if (!gpio_is_valid(priv->gpio[id].gpio)) |
|
return 0; |
|
gpio_set_value(priv->gpio[id].gpio, !!val); |
|
return 1; |
|
} |
|
|
|
static int s5k6aa_gpio_assert(struct s5k6aa *priv, int id) |
|
{ |
|
return s5k6aa_gpio_set_value(priv, id, priv->gpio[id].level); |
|
} |
|
|
|
static int s5k6aa_gpio_deassert(struct s5k6aa *priv, int id) |
|
{ |
|
return s5k6aa_gpio_set_value(priv, id, !priv->gpio[id].level); |
|
} |
|
|
|
static int __s5k6aa_power_on(struct s5k6aa *s5k6aa) |
|
{ |
|
int ret; |
|
|
|
ret = regulator_bulk_enable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); |
|
if (ret) |
|
return ret; |
|
if (s5k6aa_gpio_deassert(s5k6aa, STBY)) |
|
usleep_range(150, 200); |
|
|
|
if (s5k6aa->s_power) |
|
ret = s5k6aa->s_power(1); |
|
usleep_range(4000, 5000); |
|
|
|
if (s5k6aa_gpio_deassert(s5k6aa, RSET)) |
|
msleep(20); |
|
|
|
return ret; |
|
} |
|
|
|
static int __s5k6aa_power_off(struct s5k6aa *s5k6aa) |
|
{ |
|
int ret; |
|
|
|
if (s5k6aa_gpio_assert(s5k6aa, RSET)) |
|
usleep_range(100, 150); |
|
|
|
if (s5k6aa->s_power) { |
|
ret = s5k6aa->s_power(0); |
|
if (ret) |
|
return ret; |
|
} |
|
if (s5k6aa_gpio_assert(s5k6aa, STBY)) |
|
usleep_range(50, 100); |
|
s5k6aa->streaming = 0; |
|
|
|
return regulator_bulk_disable(S5K6AA_NUM_SUPPLIES, s5k6aa->supplies); |
|
} |
|
|
|
/* |
|
* V4L2 subdev core and video operations |
|
*/ |
|
static int s5k6aa_set_power(struct v4l2_subdev *sd, int on) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
int ret = 0; |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
|
|
if (s5k6aa->power == !on) { |
|
if (on) { |
|
ret = __s5k6aa_power_on(s5k6aa); |
|
if (!ret) |
|
ret = s5k6aa_initialize_isp(sd); |
|
} else { |
|
ret = __s5k6aa_power_off(s5k6aa); |
|
} |
|
|
|
if (!ret) |
|
s5k6aa->power += on ? 1 : -1; |
|
} |
|
|
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
if (!on || ret || s5k6aa->power != 1) |
|
return ret; |
|
|
|
return v4l2_ctrl_handler_setup(sd->ctrl_handler); |
|
} |
|
|
|
static int __s5k6aa_stream(struct s5k6aa *s5k6aa, int enable) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
int ret = 0; |
|
|
|
ret = s5k6aa_write(client, REG_G_ENABLE_PREV, enable); |
|
if (!ret) |
|
ret = s5k6aa_write(client, REG_G_ENABLE_PREV_CHG, 1); |
|
if (!ret) |
|
s5k6aa->streaming = enable; |
|
|
|
return ret; |
|
} |
|
|
|
static int s5k6aa_s_stream(struct v4l2_subdev *sd, int on) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
int ret = 0; |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
|
|
if (s5k6aa->streaming == !on) { |
|
if (!ret && s5k6aa->apply_cfg) |
|
ret = s5k6aa_set_prev_config(s5k6aa, s5k6aa->preset); |
|
if (s5k6aa->apply_crop) |
|
ret = s5k6aa_set_input_params(s5k6aa); |
|
if (!ret) |
|
ret = __s5k6aa_stream(s5k6aa, !!on); |
|
} |
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
return ret; |
|
} |
|
|
|
static int s5k6aa_g_frame_interval(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_frame_interval *fi) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
fi->interval = s5k6aa->fiv->interval; |
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
return 0; |
|
} |
|
|
|
static int __s5k6aa_set_frame_interval(struct s5k6aa *s5k6aa, |
|
struct v4l2_subdev_frame_interval *fi) |
|
{ |
|
struct v4l2_mbus_framefmt *mbus_fmt = &s5k6aa->preset->mbus_fmt; |
|
const struct s5k6aa_interval *fiv = &s5k6aa_intervals[0]; |
|
unsigned int err, min_err = UINT_MAX; |
|
unsigned int i, fr_time; |
|
|
|
if (fi->interval.denominator == 0) |
|
return -EINVAL; |
|
|
|
fr_time = fi->interval.numerator * 10000 / fi->interval.denominator; |
|
|
|
for (i = 0; i < ARRAY_SIZE(s5k6aa_intervals); i++) { |
|
const struct s5k6aa_interval *iv = &s5k6aa_intervals[i]; |
|
|
|
if (mbus_fmt->width > iv->size.width || |
|
mbus_fmt->height > iv->size.height) |
|
continue; |
|
|
|
err = abs(iv->reg_fr_time - fr_time); |
|
if (err < min_err) { |
|
fiv = iv; |
|
min_err = err; |
|
} |
|
} |
|
s5k6aa->fiv = fiv; |
|
|
|
v4l2_dbg(1, debug, &s5k6aa->sd, "Changed frame interval to %d us\n", |
|
fiv->reg_fr_time * 100); |
|
return 0; |
|
} |
|
|
|
static int s5k6aa_s_frame_interval(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_frame_interval *fi) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
int ret; |
|
|
|
v4l2_dbg(1, debug, sd, "Setting %d/%d frame interval\n", |
|
fi->interval.numerator, fi->interval.denominator); |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
ret = __s5k6aa_set_frame_interval(s5k6aa, fi); |
|
s5k6aa->apply_cfg = 1; |
|
|
|
mutex_unlock(&s5k6aa->lock); |
|
return ret; |
|
} |
|
|
|
/* |
|
* V4L2 subdev pad level and video operations |
|
*/ |
|
static int s5k6aa_enum_frame_interval(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_state *sd_state, |
|
struct v4l2_subdev_frame_interval_enum *fie) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
const struct s5k6aa_interval *fi; |
|
int ret = 0; |
|
|
|
if (fie->index >= ARRAY_SIZE(s5k6aa_intervals)) |
|
return -EINVAL; |
|
|
|
v4l_bound_align_image(&fie->width, S5K6AA_WIN_WIDTH_MIN, |
|
S5K6AA_WIN_WIDTH_MAX, 1, |
|
&fie->height, S5K6AA_WIN_HEIGHT_MIN, |
|
S5K6AA_WIN_HEIGHT_MAX, 1, 0); |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
fi = &s5k6aa_intervals[fie->index]; |
|
if (fie->width > fi->size.width || fie->height > fi->size.height) |
|
ret = -EINVAL; |
|
else |
|
fie->interval = fi->interval; |
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
return ret; |
|
} |
|
|
|
static int s5k6aa_enum_mbus_code(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_state *sd_state, |
|
struct v4l2_subdev_mbus_code_enum *code) |
|
{ |
|
if (code->index >= ARRAY_SIZE(s5k6aa_formats)) |
|
return -EINVAL; |
|
|
|
code->code = s5k6aa_formats[code->index].code; |
|
return 0; |
|
} |
|
|
|
static int s5k6aa_enum_frame_size(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_state *sd_state, |
|
struct v4l2_subdev_frame_size_enum *fse) |
|
{ |
|
int i = ARRAY_SIZE(s5k6aa_formats); |
|
|
|
if (fse->index > 0) |
|
return -EINVAL; |
|
|
|
while (--i) |
|
if (fse->code == s5k6aa_formats[i].code) |
|
break; |
|
|
|
fse->code = s5k6aa_formats[i].code; |
|
fse->min_width = S5K6AA_WIN_WIDTH_MIN; |
|
fse->max_width = S5K6AA_WIN_WIDTH_MAX; |
|
fse->max_height = S5K6AA_WIN_HEIGHT_MIN; |
|
fse->min_height = S5K6AA_WIN_HEIGHT_MAX; |
|
|
|
return 0; |
|
} |
|
|
|
static struct v4l2_rect * |
|
__s5k6aa_get_crop_rect(struct s5k6aa *s5k6aa, |
|
struct v4l2_subdev_state *sd_state, |
|
enum v4l2_subdev_format_whence which) |
|
{ |
|
if (which == V4L2_SUBDEV_FORMAT_ACTIVE) |
|
return &s5k6aa->ccd_rect; |
|
|
|
WARN_ON(which != V4L2_SUBDEV_FORMAT_TRY); |
|
return v4l2_subdev_get_try_crop(&s5k6aa->sd, sd_state, 0); |
|
} |
|
|
|
static void s5k6aa_try_format(struct s5k6aa *s5k6aa, |
|
struct v4l2_mbus_framefmt *mf) |
|
{ |
|
unsigned int index; |
|
|
|
v4l_bound_align_image(&mf->width, S5K6AA_WIN_WIDTH_MIN, |
|
S5K6AA_WIN_WIDTH_MAX, 1, |
|
&mf->height, S5K6AA_WIN_HEIGHT_MIN, |
|
S5K6AA_WIN_HEIGHT_MAX, 1, 0); |
|
|
|
if (mf->colorspace != V4L2_COLORSPACE_JPEG && |
|
mf->colorspace != V4L2_COLORSPACE_REC709) |
|
mf->colorspace = V4L2_COLORSPACE_JPEG; |
|
|
|
index = s5k6aa_get_pixfmt_index(s5k6aa, mf); |
|
|
|
mf->colorspace = s5k6aa_formats[index].colorspace; |
|
mf->code = s5k6aa_formats[index].code; |
|
mf->field = V4L2_FIELD_NONE; |
|
} |
|
|
|
static int s5k6aa_get_fmt(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_state *sd_state, |
|
struct v4l2_subdev_format *fmt) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
struct v4l2_mbus_framefmt *mf; |
|
|
|
memset(fmt->reserved, 0, sizeof(fmt->reserved)); |
|
|
|
if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { |
|
mf = v4l2_subdev_get_try_format(sd, sd_state, 0); |
|
fmt->format = *mf; |
|
return 0; |
|
} |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
fmt->format = s5k6aa->preset->mbus_fmt; |
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
return 0; |
|
} |
|
|
|
static int s5k6aa_set_fmt(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_state *sd_state, |
|
struct v4l2_subdev_format *fmt) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
struct s5k6aa_preset *preset = s5k6aa->preset; |
|
struct v4l2_mbus_framefmt *mf; |
|
struct v4l2_rect *crop; |
|
int ret = 0; |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
s5k6aa_try_format(s5k6aa, &fmt->format); |
|
|
|
if (fmt->which == V4L2_SUBDEV_FORMAT_TRY) { |
|
mf = v4l2_subdev_get_try_format(sd, sd_state, fmt->pad); |
|
crop = v4l2_subdev_get_try_crop(sd, sd_state, 0); |
|
} else { |
|
if (s5k6aa->streaming) { |
|
ret = -EBUSY; |
|
} else { |
|
mf = &preset->mbus_fmt; |
|
crop = &s5k6aa->ccd_rect; |
|
s5k6aa->apply_cfg = 1; |
|
} |
|
} |
|
|
|
if (ret == 0) { |
|
struct v4l2_subdev_frame_interval fiv = { |
|
.interval = {0, 1} |
|
}; |
|
|
|
*mf = fmt->format; |
|
/* |
|
* Make sure the crop window is valid, i.e. its size is |
|
* greater than the output window, as the ISP supports |
|
* only down-scaling. |
|
*/ |
|
crop->width = clamp_t(unsigned int, crop->width, mf->width, |
|
S5K6AA_WIN_WIDTH_MAX); |
|
crop->height = clamp_t(unsigned int, crop->height, mf->height, |
|
S5K6AA_WIN_HEIGHT_MAX); |
|
crop->left = clamp_t(unsigned int, crop->left, 0, |
|
S5K6AA_WIN_WIDTH_MAX - crop->width); |
|
crop->top = clamp_t(unsigned int, crop->top, 0, |
|
S5K6AA_WIN_HEIGHT_MAX - crop->height); |
|
|
|
/* Reset to minimum possible frame interval */ |
|
ret = __s5k6aa_set_frame_interval(s5k6aa, &fiv); |
|
} |
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
return ret; |
|
} |
|
|
|
static int s5k6aa_get_selection(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_state *sd_state, |
|
struct v4l2_subdev_selection *sel) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
struct v4l2_rect *rect; |
|
|
|
if (sel->target != V4L2_SEL_TGT_CROP) |
|
return -EINVAL; |
|
|
|
memset(sel->reserved, 0, sizeof(sel->reserved)); |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
rect = __s5k6aa_get_crop_rect(s5k6aa, sd_state, sel->which); |
|
sel->r = *rect; |
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
v4l2_dbg(1, debug, sd, "Current crop rectangle: (%d,%d)/%dx%d\n", |
|
rect->left, rect->top, rect->width, rect->height); |
|
|
|
return 0; |
|
} |
|
|
|
static int s5k6aa_set_selection(struct v4l2_subdev *sd, |
|
struct v4l2_subdev_state *sd_state, |
|
struct v4l2_subdev_selection *sel) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
struct v4l2_mbus_framefmt *mf; |
|
unsigned int max_x, max_y; |
|
struct v4l2_rect *crop_r; |
|
|
|
if (sel->target != V4L2_SEL_TGT_CROP) |
|
return -EINVAL; |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
crop_r = __s5k6aa_get_crop_rect(s5k6aa, sd_state, sel->which); |
|
|
|
if (sel->which == V4L2_SUBDEV_FORMAT_ACTIVE) { |
|
mf = &s5k6aa->preset->mbus_fmt; |
|
s5k6aa->apply_crop = 1; |
|
} else { |
|
mf = v4l2_subdev_get_try_format(sd, sd_state, 0); |
|
} |
|
v4l_bound_align_image(&sel->r.width, mf->width, |
|
S5K6AA_WIN_WIDTH_MAX, 1, |
|
&sel->r.height, mf->height, |
|
S5K6AA_WIN_HEIGHT_MAX, 1, 0); |
|
|
|
max_x = (S5K6AA_WIN_WIDTH_MAX - sel->r.width) & ~1; |
|
max_y = (S5K6AA_WIN_HEIGHT_MAX - sel->r.height) & ~1; |
|
|
|
sel->r.left = clamp_t(unsigned int, sel->r.left, 0, max_x); |
|
sel->r.top = clamp_t(unsigned int, sel->r.top, 0, max_y); |
|
|
|
*crop_r = sel->r; |
|
|
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
v4l2_dbg(1, debug, sd, "Set crop rectangle: (%d,%d)/%dx%d\n", |
|
crop_r->left, crop_r->top, crop_r->width, crop_r->height); |
|
|
|
return 0; |
|
} |
|
|
|
static const struct v4l2_subdev_pad_ops s5k6aa_pad_ops = { |
|
.enum_mbus_code = s5k6aa_enum_mbus_code, |
|
.enum_frame_size = s5k6aa_enum_frame_size, |
|
.enum_frame_interval = s5k6aa_enum_frame_interval, |
|
.get_fmt = s5k6aa_get_fmt, |
|
.set_fmt = s5k6aa_set_fmt, |
|
.get_selection = s5k6aa_get_selection, |
|
.set_selection = s5k6aa_set_selection, |
|
}; |
|
|
|
static const struct v4l2_subdev_video_ops s5k6aa_video_ops = { |
|
.g_frame_interval = s5k6aa_g_frame_interval, |
|
.s_frame_interval = s5k6aa_s_frame_interval, |
|
.s_stream = s5k6aa_s_stream, |
|
}; |
|
|
|
/* |
|
* V4L2 subdev controls |
|
*/ |
|
|
|
static int s5k6aa_s_ctrl(struct v4l2_ctrl *ctrl) |
|
{ |
|
struct v4l2_subdev *sd = ctrl_to_sd(ctrl); |
|
struct i2c_client *client = v4l2_get_subdevdata(sd); |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
int idx, err = 0; |
|
|
|
v4l2_dbg(1, debug, sd, "ctrl: 0x%x, value: %d\n", ctrl->id, ctrl->val); |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
/* |
|
* If the device is not powered up by the host driver do |
|
* not apply any controls to H/W at this time. Instead |
|
* the controls will be restored right after power-up. |
|
*/ |
|
if (s5k6aa->power == 0) |
|
goto unlock; |
|
idx = s5k6aa->preset->index; |
|
|
|
switch (ctrl->id) { |
|
case V4L2_CID_AUTO_WHITE_BALANCE: |
|
err = s5k6aa_set_awb(s5k6aa, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_BRIGHTNESS: |
|
err = s5k6aa_write(client, REG_USER_BRIGHTNESS, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_COLORFX: |
|
err = s5k6aa_set_colorfx(s5k6aa, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_CONTRAST: |
|
err = s5k6aa_write(client, REG_USER_CONTRAST, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_EXPOSURE_AUTO: |
|
err = s5k6aa_set_auto_exposure(s5k6aa, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_HFLIP: |
|
err = s5k6aa_set_mirror(s5k6aa, ctrl->val); |
|
if (err) |
|
break; |
|
err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); |
|
break; |
|
|
|
case V4L2_CID_POWER_LINE_FREQUENCY: |
|
err = s5k6aa_set_anti_flicker(s5k6aa, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_SATURATION: |
|
err = s5k6aa_write(client, REG_USER_SATURATION, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_SHARPNESS: |
|
err = s5k6aa_write(client, REG_USER_SHARPBLUR, ctrl->val); |
|
break; |
|
|
|
case V4L2_CID_WHITE_BALANCE_TEMPERATURE: |
|
err = s5k6aa_write(client, REG_P_COLORTEMP(idx), ctrl->val); |
|
if (err) |
|
break; |
|
err = s5k6aa_write(client, REG_G_PREV_CFG_CHG, 1); |
|
break; |
|
} |
|
unlock: |
|
mutex_unlock(&s5k6aa->lock); |
|
return err; |
|
} |
|
|
|
static const struct v4l2_ctrl_ops s5k6aa_ctrl_ops = { |
|
.s_ctrl = s5k6aa_s_ctrl, |
|
}; |
|
|
|
static int s5k6aa_log_status(struct v4l2_subdev *sd) |
|
{ |
|
v4l2_ctrl_handler_log_status(sd->ctrl_handler, sd->name); |
|
return 0; |
|
} |
|
|
|
#define V4L2_CID_RED_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1001) |
|
#define V4L2_CID_GREEN_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1002) |
|
#define V4L2_CID_BLUE_GAIN (V4L2_CTRL_CLASS_CAMERA | 0x1003) |
|
|
|
static const struct v4l2_ctrl_config s5k6aa_ctrls[] = { |
|
{ |
|
.ops = &s5k6aa_ctrl_ops, |
|
.id = V4L2_CID_RED_GAIN, |
|
.type = V4L2_CTRL_TYPE_INTEGER, |
|
.name = "Gain, Red", |
|
.min = 0, |
|
.max = 256, |
|
.def = 127, |
|
.step = 1, |
|
}, { |
|
.ops = &s5k6aa_ctrl_ops, |
|
.id = V4L2_CID_GREEN_GAIN, |
|
.type = V4L2_CTRL_TYPE_INTEGER, |
|
.name = "Gain, Green", |
|
.min = 0, |
|
.max = 256, |
|
.def = 127, |
|
.step = 1, |
|
}, { |
|
.ops = &s5k6aa_ctrl_ops, |
|
.id = V4L2_CID_BLUE_GAIN, |
|
.type = V4L2_CTRL_TYPE_INTEGER, |
|
.name = "Gain, Blue", |
|
.min = 0, |
|
.max = 256, |
|
.def = 127, |
|
.step = 1, |
|
}, |
|
}; |
|
|
|
static int s5k6aa_initialize_ctrls(struct s5k6aa *s5k6aa) |
|
{ |
|
const struct v4l2_ctrl_ops *ops = &s5k6aa_ctrl_ops; |
|
struct s5k6aa_ctrls *ctrls = &s5k6aa->ctrls; |
|
struct v4l2_ctrl_handler *hdl = &ctrls->handler; |
|
|
|
int ret = v4l2_ctrl_handler_init(hdl, 16); |
|
if (ret) |
|
return ret; |
|
/* Auto white balance cluster */ |
|
ctrls->awb = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_AUTO_WHITE_BALANCE, |
|
0, 1, 1, 1); |
|
ctrls->gain_red = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[0], NULL); |
|
ctrls->gain_green = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[1], NULL); |
|
ctrls->gain_blue = v4l2_ctrl_new_custom(hdl, &s5k6aa_ctrls[2], NULL); |
|
v4l2_ctrl_auto_cluster(4, &ctrls->awb, 0, false); |
|
|
|
ctrls->hflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_HFLIP, 0, 1, 1, 0); |
|
ctrls->vflip = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_VFLIP, 0, 1, 1, 0); |
|
v4l2_ctrl_cluster(2, &ctrls->hflip); |
|
|
|
ctrls->auto_exp = v4l2_ctrl_new_std_menu(hdl, ops, |
|
V4L2_CID_EXPOSURE_AUTO, |
|
V4L2_EXPOSURE_MANUAL, 0, V4L2_EXPOSURE_AUTO); |
|
/* Exposure time: x 1 us */ |
|
ctrls->exposure = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_EXPOSURE, |
|
0, 6000000U, 1, 100000U); |
|
/* Total gain: 256 <=> 1x */ |
|
ctrls->gain = v4l2_ctrl_new_std(hdl, ops, V4L2_CID_GAIN, |
|
0, 256, 1, 256); |
|
v4l2_ctrl_auto_cluster(3, &ctrls->auto_exp, 0, false); |
|
|
|
v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_POWER_LINE_FREQUENCY, |
|
V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0, |
|
V4L2_CID_POWER_LINE_FREQUENCY_AUTO); |
|
|
|
v4l2_ctrl_new_std_menu(hdl, ops, V4L2_CID_COLORFX, |
|
V4L2_COLORFX_SKY_BLUE, ~0x6f, V4L2_COLORFX_NONE); |
|
|
|
v4l2_ctrl_new_std(hdl, ops, V4L2_CID_WHITE_BALANCE_TEMPERATURE, |
|
0, 256, 1, 0); |
|
|
|
v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SATURATION, -127, 127, 1, 0); |
|
v4l2_ctrl_new_std(hdl, ops, V4L2_CID_BRIGHTNESS, -127, 127, 1, 0); |
|
v4l2_ctrl_new_std(hdl, ops, V4L2_CID_CONTRAST, -127, 127, 1, 0); |
|
v4l2_ctrl_new_std(hdl, ops, V4L2_CID_SHARPNESS, -127, 127, 1, 0); |
|
|
|
if (hdl->error) { |
|
ret = hdl->error; |
|
v4l2_ctrl_handler_free(hdl); |
|
return ret; |
|
} |
|
|
|
s5k6aa->sd.ctrl_handler = hdl; |
|
return 0; |
|
} |
|
|
|
/* |
|
* V4L2 subdev internal operations |
|
*/ |
|
static int s5k6aa_open(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh) |
|
{ |
|
struct v4l2_mbus_framefmt *format = v4l2_subdev_get_try_format(sd, |
|
fh->state, |
|
0); |
|
struct v4l2_rect *crop = v4l2_subdev_get_try_crop(sd, fh->state, 0); |
|
|
|
format->colorspace = s5k6aa_formats[0].colorspace; |
|
format->code = s5k6aa_formats[0].code; |
|
format->width = S5K6AA_OUT_WIDTH_DEF; |
|
format->height = S5K6AA_OUT_HEIGHT_DEF; |
|
format->field = V4L2_FIELD_NONE; |
|
|
|
crop->width = S5K6AA_WIN_WIDTH_MAX; |
|
crop->height = S5K6AA_WIN_HEIGHT_MAX; |
|
crop->left = 0; |
|
crop->top = 0; |
|
|
|
return 0; |
|
} |
|
|
|
static int s5k6aa_check_fw_revision(struct s5k6aa *s5k6aa) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
u16 api_ver = 0, fw_rev = 0; |
|
|
|
int ret = s5k6aa_set_ahb_address(client); |
|
|
|
if (!ret) |
|
ret = s5k6aa_read(client, REG_FW_APIVER, &api_ver); |
|
if (!ret) |
|
ret = s5k6aa_read(client, REG_FW_REVISION, &fw_rev); |
|
if (ret) { |
|
v4l2_err(&s5k6aa->sd, "FW revision check failed!\n"); |
|
return ret; |
|
} |
|
|
|
v4l2_info(&s5k6aa->sd, "FW API ver.: 0x%X, FW rev.: 0x%X\n", |
|
api_ver, fw_rev); |
|
|
|
return api_ver == S5K6AAFX_FW_APIVER ? 0 : -ENODEV; |
|
} |
|
|
|
static int s5k6aa_registered(struct v4l2_subdev *sd) |
|
{ |
|
struct s5k6aa *s5k6aa = to_s5k6aa(sd); |
|
int ret; |
|
|
|
mutex_lock(&s5k6aa->lock); |
|
ret = __s5k6aa_power_on(s5k6aa); |
|
if (!ret) { |
|
msleep(100); |
|
ret = s5k6aa_check_fw_revision(s5k6aa); |
|
__s5k6aa_power_off(s5k6aa); |
|
} |
|
mutex_unlock(&s5k6aa->lock); |
|
|
|
return ret; |
|
} |
|
|
|
static const struct v4l2_subdev_internal_ops s5k6aa_subdev_internal_ops = { |
|
.registered = s5k6aa_registered, |
|
.open = s5k6aa_open, |
|
}; |
|
|
|
static const struct v4l2_subdev_core_ops s5k6aa_core_ops = { |
|
.s_power = s5k6aa_set_power, |
|
.log_status = s5k6aa_log_status, |
|
}; |
|
|
|
static const struct v4l2_subdev_ops s5k6aa_subdev_ops = { |
|
.core = &s5k6aa_core_ops, |
|
.pad = &s5k6aa_pad_ops, |
|
.video = &s5k6aa_video_ops, |
|
}; |
|
|
|
/* |
|
* GPIO setup |
|
*/ |
|
|
|
static int s5k6aa_configure_gpios(struct s5k6aa *s5k6aa, |
|
const struct s5k6aa_platform_data *pdata) |
|
{ |
|
struct i2c_client *client = v4l2_get_subdevdata(&s5k6aa->sd); |
|
const struct s5k6aa_gpio *gpio; |
|
unsigned long flags; |
|
int ret; |
|
|
|
s5k6aa->gpio[STBY].gpio = -EINVAL; |
|
s5k6aa->gpio[RSET].gpio = -EINVAL; |
|
|
|
gpio = &pdata->gpio_stby; |
|
if (gpio_is_valid(gpio->gpio)) { |
|
flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW) |
|
| GPIOF_EXPORT; |
|
ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags, |
|
"S5K6AA_STBY"); |
|
if (ret < 0) |
|
return ret; |
|
|
|
s5k6aa->gpio[STBY] = *gpio; |
|
} |
|
|
|
gpio = &pdata->gpio_reset; |
|
if (gpio_is_valid(gpio->gpio)) { |
|
flags = (gpio->level ? GPIOF_OUT_INIT_HIGH : GPIOF_OUT_INIT_LOW) |
|
| GPIOF_EXPORT; |
|
ret = devm_gpio_request_one(&client->dev, gpio->gpio, flags, |
|
"S5K6AA_RST"); |
|
if (ret < 0) |
|
return ret; |
|
|
|
s5k6aa->gpio[RSET] = *gpio; |
|
} |
|
|
|
return 0; |
|
} |
|
|
|
static int s5k6aa_probe(struct i2c_client *client, |
|
const struct i2c_device_id *id) |
|
{ |
|
const struct s5k6aa_platform_data *pdata = client->dev.platform_data; |
|
struct v4l2_subdev *sd; |
|
struct s5k6aa *s5k6aa; |
|
int i, ret; |
|
|
|
if (pdata == NULL) { |
|
dev_err(&client->dev, "Platform data not specified\n"); |
|
return -EINVAL; |
|
} |
|
|
|
if (pdata->mclk_frequency == 0) { |
|
dev_err(&client->dev, "MCLK frequency not specified\n"); |
|
return -EINVAL; |
|
} |
|
|
|
s5k6aa = devm_kzalloc(&client->dev, sizeof(*s5k6aa), GFP_KERNEL); |
|
if (!s5k6aa) |
|
return -ENOMEM; |
|
|
|
mutex_init(&s5k6aa->lock); |
|
|
|
s5k6aa->mclk_frequency = pdata->mclk_frequency; |
|
s5k6aa->bus_type = pdata->bus_type; |
|
s5k6aa->mipi_lanes = pdata->nlanes; |
|
s5k6aa->s_power = pdata->set_power; |
|
s5k6aa->inv_hflip = pdata->horiz_flip; |
|
s5k6aa->inv_vflip = pdata->vert_flip; |
|
|
|
sd = &s5k6aa->sd; |
|
v4l2_i2c_subdev_init(sd, client, &s5k6aa_subdev_ops); |
|
/* Static name; NEVER use in new drivers! */ |
|
strscpy(sd->name, DRIVER_NAME, sizeof(sd->name)); |
|
|
|
sd->internal_ops = &s5k6aa_subdev_internal_ops; |
|
sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; |
|
|
|
s5k6aa->pad.flags = MEDIA_PAD_FL_SOURCE; |
|
sd->entity.function = MEDIA_ENT_F_CAM_SENSOR; |
|
ret = media_entity_pads_init(&sd->entity, 1, &s5k6aa->pad); |
|
if (ret) |
|
return ret; |
|
|
|
ret = s5k6aa_configure_gpios(s5k6aa, pdata); |
|
if (ret) |
|
goto out_err; |
|
|
|
for (i = 0; i < S5K6AA_NUM_SUPPLIES; i++) |
|
s5k6aa->supplies[i].supply = s5k6aa_supply_names[i]; |
|
|
|
ret = devm_regulator_bulk_get(&client->dev, S5K6AA_NUM_SUPPLIES, |
|
s5k6aa->supplies); |
|
if (ret) { |
|
dev_err(&client->dev, "Failed to get regulators\n"); |
|
goto out_err; |
|
} |
|
|
|
ret = s5k6aa_initialize_ctrls(s5k6aa); |
|
if (ret) |
|
goto out_err; |
|
|
|
s5k6aa_presets_data_init(s5k6aa); |
|
|
|
s5k6aa->ccd_rect.width = S5K6AA_WIN_WIDTH_MAX; |
|
s5k6aa->ccd_rect.height = S5K6AA_WIN_HEIGHT_MAX; |
|
s5k6aa->ccd_rect.left = 0; |
|
s5k6aa->ccd_rect.top = 0; |
|
|
|
return 0; |
|
|
|
out_err: |
|
media_entity_cleanup(&s5k6aa->sd.entity); |
|
return ret; |
|
} |
|
|
|
static int s5k6aa_remove(struct i2c_client *client) |
|
{ |
|
struct v4l2_subdev *sd = i2c_get_clientdata(client); |
|
|
|
v4l2_device_unregister_subdev(sd); |
|
v4l2_ctrl_handler_free(sd->ctrl_handler); |
|
media_entity_cleanup(&sd->entity); |
|
|
|
return 0; |
|
} |
|
|
|
static const struct i2c_device_id s5k6aa_id[] = { |
|
{ DRIVER_NAME, 0 }, |
|
{ }, |
|
}; |
|
MODULE_DEVICE_TABLE(i2c, s5k6aa_id); |
|
|
|
|
|
static struct i2c_driver s5k6aa_i2c_driver = { |
|
.driver = { |
|
.name = DRIVER_NAME |
|
}, |
|
.probe = s5k6aa_probe, |
|
.remove = s5k6aa_remove, |
|
.id_table = s5k6aa_id, |
|
}; |
|
|
|
module_i2c_driver(s5k6aa_i2c_driver); |
|
|
|
MODULE_DESCRIPTION("Samsung S5K6AA(FX) SXGA camera driver"); |
|
MODULE_AUTHOR("Sylwester Nawrocki <[email protected]>"); |
|
MODULE_LICENSE("GPL");
|
|
|