mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
320 lines
8.0 KiB
320 lines
8.0 KiB
// SPDX-License-Identifier: GPL-2.0-or-later |
|
/* |
|
* QNAP TS-409 Board Setup |
|
* |
|
* Maintainer: Sylver Bruneau <[email protected]> |
|
* |
|
* Copyright (C) 2008 Sylver Bruneau <[email protected]> |
|
* Copyright (C) 2008 Martin Michlmayr <[email protected]> |
|
*/ |
|
#include <linux/gpio.h> |
|
#include <linux/kernel.h> |
|
#include <linux/init.h> |
|
#include <linux/platform_device.h> |
|
#include <linux/pci.h> |
|
#include <linux/irq.h> |
|
#include <linux/mtd/physmap.h> |
|
#include <linux/mv643xx_eth.h> |
|
#include <linux/leds.h> |
|
#include <linux/gpio_keys.h> |
|
#include <linux/input.h> |
|
#include <linux/i2c.h> |
|
#include <linux/serial_reg.h> |
|
#include <asm/mach-types.h> |
|
#include <asm/mach/arch.h> |
|
#include <asm/mach/pci.h> |
|
#include "common.h" |
|
#include "mpp.h" |
|
#include "orion5x.h" |
|
#include "tsx09-common.h" |
|
|
|
/***************************************************************************** |
|
* QNAP TS-409 Info |
|
****************************************************************************/ |
|
|
|
/* |
|
* QNAP TS-409 hardware : |
|
* - Marvell 88F5281-D0 |
|
* - Marvell 88SX7042 SATA controller (PCIe) |
|
* - Marvell 88E1118 Gigabit Ethernet PHY |
|
* - RTC S35390A (@0x30) on I2C bus |
|
* - 8MB NOR flash |
|
* - 256MB of DDR-2 RAM |
|
*/ |
|
|
|
/* |
|
* 8MB NOR flash Device bus boot chip select |
|
*/ |
|
|
|
#define QNAP_TS409_NOR_BOOT_BASE 0xff800000 |
|
#define QNAP_TS409_NOR_BOOT_SIZE SZ_8M |
|
|
|
/**************************************************************************** |
|
* 8MiB NOR flash. The struct mtd_partition is not in the same order as the |
|
* partitions on the device because we want to keep compatibility with |
|
* existing QNAP firmware. |
|
* |
|
* Layout as used by QNAP: |
|
* [2] 0x00000000-0x00200000 : "Kernel" |
|
* [3] 0x00200000-0x00600000 : "RootFS1" |
|
* [4] 0x00600000-0x00700000 : "RootFS2" |
|
* [6] 0x00700000-0x00760000 : "NAS Config" (read-only) |
|
* [5] 0x00760000-0x00780000 : "U-Boot Config" |
|
* [1] 0x00780000-0x00800000 : "U-Boot" (read-only) |
|
***************************************************************************/ |
|
static struct mtd_partition qnap_ts409_partitions[] = { |
|
{ |
|
.name = "U-Boot", |
|
.size = 0x00080000, |
|
.offset = 0x00780000, |
|
.mask_flags = MTD_WRITEABLE, |
|
}, { |
|
.name = "Kernel", |
|
.size = 0x00200000, |
|
.offset = 0, |
|
}, { |
|
.name = "RootFS1", |
|
.size = 0x00400000, |
|
.offset = 0x00200000, |
|
}, { |
|
.name = "RootFS2", |
|
.size = 0x00100000, |
|
.offset = 0x00600000, |
|
}, { |
|
.name = "U-Boot Config", |
|
.size = 0x00020000, |
|
.offset = 0x00760000, |
|
}, { |
|
.name = "NAS Config", |
|
.size = 0x00060000, |
|
.offset = 0x00700000, |
|
.mask_flags = MTD_WRITEABLE, |
|
}, |
|
}; |
|
|
|
static struct physmap_flash_data qnap_ts409_nor_flash_data = { |
|
.width = 1, |
|
.parts = qnap_ts409_partitions, |
|
.nr_parts = ARRAY_SIZE(qnap_ts409_partitions) |
|
}; |
|
|
|
static struct resource qnap_ts409_nor_flash_resource = { |
|
.flags = IORESOURCE_MEM, |
|
.start = QNAP_TS409_NOR_BOOT_BASE, |
|
.end = QNAP_TS409_NOR_BOOT_BASE + QNAP_TS409_NOR_BOOT_SIZE - 1, |
|
}; |
|
|
|
static struct platform_device qnap_ts409_nor_flash = { |
|
.name = "physmap-flash", |
|
.id = 0, |
|
.dev = { .platform_data = &qnap_ts409_nor_flash_data, }, |
|
.num_resources = 1, |
|
.resource = &qnap_ts409_nor_flash_resource, |
|
}; |
|
|
|
/***************************************************************************** |
|
* PCI |
|
****************************************************************************/ |
|
|
|
static int __init qnap_ts409_pci_map_irq(const struct pci_dev *dev, u8 slot, |
|
u8 pin) |
|
{ |
|
int irq; |
|
|
|
/* |
|
* Check for devices with hard-wired IRQs. |
|
*/ |
|
irq = orion5x_pci_map_irq(dev, slot, pin); |
|
if (irq != -1) |
|
return irq; |
|
|
|
/* |
|
* PCI isn't used on the TS-409 |
|
*/ |
|
return -1; |
|
} |
|
|
|
static struct hw_pci qnap_ts409_pci __initdata = { |
|
.nr_controllers = 2, |
|
.setup = orion5x_pci_sys_setup, |
|
.scan = orion5x_pci_sys_scan_bus, |
|
.map_irq = qnap_ts409_pci_map_irq, |
|
}; |
|
|
|
static int __init qnap_ts409_pci_init(void) |
|
{ |
|
if (machine_is_ts409()) |
|
pci_common_init(&qnap_ts409_pci); |
|
|
|
return 0; |
|
} |
|
|
|
subsys_initcall(qnap_ts409_pci_init); |
|
|
|
/***************************************************************************** |
|
* RTC S35390A on I2C bus |
|
****************************************************************************/ |
|
|
|
#define TS409_RTC_GPIO 10 |
|
|
|
static struct i2c_board_info __initdata qnap_ts409_i2c_rtc = { |
|
I2C_BOARD_INFO("s35390a", 0x30), |
|
}; |
|
|
|
/***************************************************************************** |
|
* LEDs attached to GPIO |
|
****************************************************************************/ |
|
|
|
static struct gpio_led ts409_led_pins[] = { |
|
{ |
|
.name = "ts409:red:sata1", |
|
.gpio = 4, |
|
.active_low = 1, |
|
}, { |
|
.name = "ts409:red:sata2", |
|
.gpio = 5, |
|
.active_low = 1, |
|
}, { |
|
.name = "ts409:red:sata3", |
|
.gpio = 6, |
|
.active_low = 1, |
|
}, { |
|
.name = "ts409:red:sata4", |
|
.gpio = 7, |
|
.active_low = 1, |
|
}, |
|
}; |
|
|
|
static struct gpio_led_platform_data ts409_led_data = { |
|
.leds = ts409_led_pins, |
|
.num_leds = ARRAY_SIZE(ts409_led_pins), |
|
}; |
|
|
|
static struct platform_device ts409_leds = { |
|
.name = "leds-gpio", |
|
.id = -1, |
|
.dev = { |
|
.platform_data = &ts409_led_data, |
|
}, |
|
}; |
|
|
|
/**************************************************************************** |
|
* GPIO Attached Keys |
|
* Power button is attached to the PIC microcontroller |
|
****************************************************************************/ |
|
|
|
#define QNAP_TS409_GPIO_KEY_RESET 14 |
|
#define QNAP_TS409_GPIO_KEY_MEDIA 15 |
|
|
|
static struct gpio_keys_button qnap_ts409_buttons[] = { |
|
{ |
|
.code = KEY_RESTART, |
|
.gpio = QNAP_TS409_GPIO_KEY_RESET, |
|
.desc = "Reset Button", |
|
.active_low = 1, |
|
}, { |
|
.code = KEY_COPY, |
|
.gpio = QNAP_TS409_GPIO_KEY_MEDIA, |
|
.desc = "USB Copy Button", |
|
.active_low = 1, |
|
}, |
|
}; |
|
|
|
static struct gpio_keys_platform_data qnap_ts409_button_data = { |
|
.buttons = qnap_ts409_buttons, |
|
.nbuttons = ARRAY_SIZE(qnap_ts409_buttons), |
|
}; |
|
|
|
static struct platform_device qnap_ts409_button_device = { |
|
.name = "gpio-keys", |
|
.id = -1, |
|
.num_resources = 0, |
|
.dev = { |
|
.platform_data = &qnap_ts409_button_data, |
|
}, |
|
}; |
|
|
|
/***************************************************************************** |
|
* General Setup |
|
****************************************************************************/ |
|
static unsigned int ts409_mpp_modes[] __initdata = { |
|
MPP0_UNUSED, |
|
MPP1_UNUSED, |
|
MPP2_UNUSED, |
|
MPP3_UNUSED, |
|
MPP4_GPIO, /* HDD 1 status */ |
|
MPP5_GPIO, /* HDD 2 status */ |
|
MPP6_GPIO, /* HDD 3 status */ |
|
MPP7_GPIO, /* HDD 4 status */ |
|
MPP8_UNUSED, |
|
MPP9_UNUSED, |
|
MPP10_GPIO, /* RTC int */ |
|
MPP11_UNUSED, |
|
MPP12_UNUSED, |
|
MPP13_UNUSED, |
|
MPP14_GPIO, /* SW_RST */ |
|
MPP15_GPIO, /* USB copy button */ |
|
MPP16_UART, /* UART1 RXD */ |
|
MPP17_UART, /* UART1 TXD */ |
|
MPP18_UNUSED, |
|
MPP19_UNUSED, |
|
0, |
|
}; |
|
|
|
static void __init qnap_ts409_init(void) |
|
{ |
|
/* |
|
* Setup basic Orion functions. Need to be called early. |
|
*/ |
|
orion5x_init(); |
|
|
|
orion5x_mpp_conf(ts409_mpp_modes); |
|
|
|
/* |
|
* Configure peripherals. |
|
*/ |
|
mvebu_mbus_add_window_by_id(ORION_MBUS_DEVBUS_BOOT_TARGET, |
|
ORION_MBUS_DEVBUS_BOOT_ATTR, |
|
QNAP_TS409_NOR_BOOT_BASE, |
|
QNAP_TS409_NOR_BOOT_SIZE); |
|
platform_device_register(&qnap_ts409_nor_flash); |
|
|
|
orion5x_ehci0_init(); |
|
qnap_tsx09_find_mac_addr(QNAP_TS409_NOR_BOOT_BASE + |
|
qnap_ts409_partitions[5].offset, |
|
qnap_ts409_partitions[5].size); |
|
orion5x_eth_init(&qnap_tsx09_eth_data); |
|
orion5x_i2c_init(); |
|
orion5x_uart0_init(); |
|
orion5x_uart1_init(); |
|
|
|
platform_device_register(&qnap_ts409_button_device); |
|
|
|
/* Get RTC IRQ and register the chip */ |
|
if (gpio_request(TS409_RTC_GPIO, "rtc") == 0) { |
|
if (gpio_direction_input(TS409_RTC_GPIO) == 0) |
|
qnap_ts409_i2c_rtc.irq = gpio_to_irq(TS409_RTC_GPIO); |
|
else |
|
gpio_free(TS409_RTC_GPIO); |
|
} |
|
if (qnap_ts409_i2c_rtc.irq == 0) |
|
pr_warn("qnap_ts409_init: failed to get RTC IRQ\n"); |
|
i2c_register_board_info(0, &qnap_ts409_i2c_rtc, 1); |
|
platform_device_register(&ts409_leds); |
|
|
|
/* register tsx09 specific power-off method */ |
|
pm_power_off = qnap_tsx09_power_off; |
|
} |
|
|
|
MACHINE_START(TS409, "QNAP TS-409") |
|
/* Maintainer: Sylver Bruneau <[email protected]> */ |
|
.atag_offset = 0x100, |
|
.nr_irqs = ORION5X_NR_IRQS, |
|
.init_machine = qnap_ts409_init, |
|
.map_io = orion5x_map_io, |
|
.init_early = orion5x_init_early, |
|
.init_irq = orion5x_init_irq, |
|
.init_time = orion5x_timer_init, |
|
.fixup = tag_fixup_mem32, |
|
.restart = orion5x_restart, |
|
MACHINE_END
|
|
|