mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
143 lines
2.4 KiB
143 lines
2.4 KiB
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
|
// Copyright (C) 2017 Jagan Teki <[email protected]> |
|
|
|
/dts-v1/; |
|
|
|
#include "sun50i-h5.dtsi" |
|
|
|
#include <dt-bindings/gpio/gpio.h> |
|
|
|
/ { |
|
model = "OrangePi Zero Plus2"; |
|
compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5"; |
|
|
|
aliases { |
|
serial0 = &uart0; |
|
}; |
|
|
|
chosen { |
|
stdout-path = "serial0:115200n8"; |
|
}; |
|
|
|
connector { |
|
compatible = "hdmi-connector"; |
|
type = "a"; |
|
|
|
port { |
|
hdmi_con_in: endpoint { |
|
remote-endpoint = <&hdmi_out_con>; |
|
}; |
|
}; |
|
}; |
|
|
|
leds { |
|
compatible = "gpio-leds"; |
|
|
|
led-0 { |
|
label = "orangepi:green:pwr"; |
|
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; |
|
default-state = "on"; |
|
}; |
|
|
|
led-1 { |
|
label = "orangepi:red:status"; |
|
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; |
|
}; |
|
}; |
|
|
|
reg_vcc3v3: vcc3v3 { |
|
compatible = "regulator-fixed"; |
|
regulator-name = "vcc3v3"; |
|
regulator-min-microvolt = <3300000>; |
|
regulator-max-microvolt = <3300000>; |
|
}; |
|
|
|
wifi_pwrseq: wifi_pwrseq { |
|
compatible = "mmc-pwrseq-simple"; |
|
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */ |
|
post-power-on-delay-ms = <200>; |
|
}; |
|
}; |
|
|
|
&de { |
|
status = "okay"; |
|
}; |
|
|
|
&ehci0 { |
|
status = "okay"; |
|
}; |
|
|
|
&hdmi { |
|
status = "okay"; |
|
}; |
|
|
|
&hdmi_out { |
|
hdmi_out_con: endpoint { |
|
remote-endpoint = <&hdmi_con_in>; |
|
}; |
|
}; |
|
|
|
&mmc0 { |
|
vmmc-supply = <®_vcc3v3>; |
|
bus-width = <4>; |
|
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; |
|
status = "okay"; |
|
}; |
|
|
|
&mmc1 { |
|
vmmc-supply = <®_vcc3v3>; |
|
vqmmc-supply = <®_vcc3v3>; |
|
mmc-pwrseq = <&wifi_pwrseq>; |
|
bus-width = <4>; |
|
non-removable; |
|
status = "okay"; |
|
|
|
brcmf: wifi@1 { |
|
reg = <1>; |
|
compatible = "brcm,bcm4329-fmac"; |
|
interrupt-parent = <&r_pio>; |
|
interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */ |
|
interrupt-names = "host-wake"; |
|
}; |
|
}; |
|
|
|
&mmc2 { |
|
pinctrl-names = "default"; |
|
pinctrl-0 = <&mmc2_8bit_pins>; |
|
vmmc-supply = <®_vcc3v3>; |
|
bus-width = <8>; |
|
non-removable; |
|
cap-mmc-hw-reset; |
|
status = "okay"; |
|
}; |
|
|
|
&ohci0 { |
|
status = "okay"; |
|
}; |
|
|
|
&uart0 { |
|
pinctrl-names = "default"; |
|
pinctrl-0 = <&uart0_pa_pins>; |
|
status = "okay"; |
|
}; |
|
|
|
&uart1 { |
|
pinctrl-names = "default"; |
|
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; |
|
status = "okay"; |
|
}; |
|
|
|
&usb_otg { |
|
/* |
|
* According to schematics CN1 MicroUSB port can be used to take |
|
* external 5V to power up the board VBUS. On the contrary CN1 MicroUSB |
|
* port cannot provide power externally even if the board is powered |
|
* via GPIO pins. It thus makes sense to force peripheral mode. |
|
*/ |
|
dr_mode = "peripheral"; |
|
status = "okay"; |
|
}; |
|
|
|
&usbphy { |
|
status = "okay"; |
|
};
|
|
|