mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
106 lines
3.1 KiB
106 lines
3.1 KiB
# SPDX-License-Identifier: GPL-2.0-only |
|
# |
|
# Freescale device configuration |
|
# |
|
|
|
config NET_VENDOR_FREESCALE |
|
bool "Freescale devices" |
|
default y |
|
depends on FSL_SOC || QUICC_ENGINE || CPM1 || CPM2 || PPC_MPC512x || \ |
|
M523x || M527x || M5272 || M528x || M520x || M532x || \ |
|
ARCH_MXC || ARCH_MXS || (PPC_MPC52xx && PPC_BESTCOMM) || \ |
|
ARCH_LAYERSCAPE || COMPILE_TEST |
|
help |
|
If you have a network (Ethernet) card belonging to this class, say Y. |
|
|
|
Note that the answer to this question doesn't directly affect the |
|
kernel: saying N will just cause the configurator to skip all |
|
the questions about Freescale devices. If you say Y, you will be |
|
asked for your specific card in the following questions. |
|
|
|
if NET_VENDOR_FREESCALE |
|
|
|
config FEC |
|
tristate "FEC ethernet controller (of ColdFire and some i.MX CPUs)" |
|
depends on (M523x || M527x || M5272 || M528x || M520x || M532x || \ |
|
ARCH_MXC || SOC_IMX28 || COMPILE_TEST) |
|
default ARCH_MXC || SOC_IMX28 if ARM |
|
select CRC32 |
|
select PHYLIB |
|
imply PTP_1588_CLOCK |
|
help |
|
Say Y here if you want to use the built-in 10/100 Fast ethernet |
|
controller on some Motorola ColdFire and Freescale i.MX processors. |
|
|
|
config FEC_MPC52xx |
|
tristate "FEC MPC52xx driver" |
|
depends on PPC_MPC52xx && PPC_BESTCOMM |
|
select CRC32 |
|
select PHYLIB |
|
select PPC_BESTCOMM_FEC |
|
help |
|
This option enables support for the MPC5200's on-chip |
|
Fast Ethernet Controller |
|
If compiled as module, it will be called fec_mpc52xx. |
|
|
|
config FEC_MPC52xx_MDIO |
|
bool "FEC MPC52xx MDIO bus driver" |
|
depends on FEC_MPC52xx |
|
default y |
|
help |
|
The MPC5200's FEC can connect to the Ethernet either with |
|
an external MII PHY chip or 10 Mbps 7-wire interface |
|
(Motorola? industry standard). |
|
If your board uses an external PHY connected to FEC, enable this. |
|
If not sure, enable. |
|
If compiled as module, it will be called fec_mpc52xx_phy. |
|
|
|
source "drivers/net/ethernet/freescale/fs_enet/Kconfig" |
|
source "drivers/net/ethernet/freescale/fman/Kconfig" |
|
|
|
config FSL_PQ_MDIO |
|
tristate "Freescale PQ MDIO" |
|
select PHYLIB |
|
help |
|
This driver supports the MDIO bus used by the gianfar and UCC drivers. |
|
|
|
config FSL_XGMAC_MDIO |
|
tristate "Freescale XGMAC MDIO" |
|
select PHYLIB |
|
depends on OF |
|
select OF_MDIO |
|
help |
|
This driver supports the MDIO bus on the Fman 10G Ethernet MACs, and |
|
on the FMan mEMAC (which supports both Clauses 22 and 45) |
|
|
|
config UCC_GETH |
|
tristate "Freescale QE Gigabit Ethernet" |
|
depends on QUICC_ENGINE && PPC32 |
|
select FSL_PQ_MDIO |
|
select PHYLIB |
|
select FIXED_PHY |
|
help |
|
This driver supports the Gigabit Ethernet mode of the QUICC Engine, |
|
which is available on some Freescale SOCs. |
|
|
|
config UGETH_TX_ON_DEMAND |
|
bool "Transmit on Demand support" |
|
depends on UCC_GETH |
|
|
|
config GIANFAR |
|
tristate "Gianfar Ethernet" |
|
depends on HAS_DMA |
|
select FSL_PQ_MDIO |
|
select PHYLIB |
|
select FIXED_PHY |
|
select CRC32 |
|
help |
|
This driver supports the Gigabit TSEC on the MPC83xx, MPC85xx, |
|
and MPC86xx family of chips, the eTSEC on LS1021A and the FEC |
|
on the 8540. |
|
|
|
source "drivers/net/ethernet/freescale/dpaa/Kconfig" |
|
source "drivers/net/ethernet/freescale/dpaa2/Kconfig" |
|
source "drivers/net/ethernet/freescale/enetc/Kconfig" |
|
|
|
endif # NET_VENDOR_FREESCALE
|
|
|