mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
62 lines
2.2 KiB
62 lines
2.2 KiB
Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger |
|
|
|
Required properties: |
|
- compatible: Should contain one of the following: |
|
* "ti,bq24250" |
|
* "ti,bq24251" |
|
* "ti,bq24257" |
|
- reg: integer, i2c address of the device. |
|
- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in |
|
conjunction with "interrupt-parent". |
|
- ti,battery-regulation-voltage: integer, maximum charging voltage in uV. |
|
- ti,charge-current: integer, maximum charging current in uA. |
|
- ti,termination-current: integer, charge will be terminated when current in |
|
constant-voltage phase drops below this value (in uA). |
|
|
|
Optional properties: |
|
- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. |
|
This pin is not available on all devices however it should be used if |
|
possible as this is the recommended way to obtain the charger's input PG |
|
state. If this pin is not specified a software-based approach for PG |
|
detection is used. |
|
- ti,current-limit: The maximum current to be drawn from the charger's input |
|
(in uA). If this property is not specified, the input limit current is |
|
set automatically using USB D+/D- signal based charger type detection. |
|
If the hardware does not support the D+/D- based detection, a default |
|
of 500,000 is used (=500mA) instead. |
|
- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If |
|
not specified a default of 6,5000,000 (=6.5V) is used. |
|
- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic |
|
power path management (in uV). If not specified a default of 4,360,000 |
|
(=4.36V) is used. |
|
|
|
Example: |
|
|
|
bq24257 { |
|
compatible = "ti,bq24257"; |
|
reg = <0x6a>; |
|
interrupt-parent = <&gpio1>; |
|
interrupts = <16 IRQ_TYPE_EDGE_BOTH>; |
|
|
|
pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; |
|
|
|
ti,battery-regulation-voltage = <4200000>; |
|
ti,charge-current = <1000000>; |
|
ti,termination-current = <50000>; |
|
}; |
|
|
|
Example: |
|
|
|
bq24250 { |
|
compatible = "ti,bq24250"; |
|
reg = <0x6a>; |
|
interrupt-parent = <&gpio1>; |
|
interrupts = <16 IRQ_TYPE_EDGE_BOTH>; |
|
|
|
ti,battery-regulation-voltage = <4200000>; |
|
ti,charge-current = <500000>; |
|
ti,termination-current = <50000>; |
|
ti,current-limit = <900000>; |
|
ti,ovp-voltage = <9500000>; |
|
ti,in-dpm-voltage = <4440000>; |
|
};
|
|
|