mirror of https://github.com/Qortal/Brooklyn
You can not select more than 25 topics
Topics must start with a letter or number, can include dashes ('-') and can be up to 35 characters long.
56 lines
2.5 KiB
56 lines
2.5 KiB
* Marvell UART : Non standard UART used in some of Marvell EBU SoCs |
|
e.g., Armada-3700. |
|
|
|
Required properties: |
|
- compatible: |
|
- "marvell,armada-3700-uart" for the standard variant of the UART |
|
(32 bytes FIFO, no DMA, level interrupts, 8-bit access to the |
|
FIFO), called also UART1. |
|
- "marvell,armada-3700-uart-ext" for the extended variant of the |
|
UART (128 bytes FIFO, DMA, front interrupts, 8-bit or 32-bit |
|
accesses to the FIFO), called also UART2. |
|
- reg: offset and length of the register set for the device. |
|
- clocks: UART reference clock used to derive the baudrate. If no clock |
|
is provided (possible only with the "marvell,armada-3700-uart" |
|
compatible string for backward compatibility), it will only work |
|
if the baudrate was initialized by the bootloader and no baudrate |
|
change will then be possible. When provided it should be UART1-clk |
|
for standard variant of UART and UART2-clk for extended variant |
|
of UART. TBG clock (with UART TBG divisors d1=d2=1) or xtal clock |
|
should not be used and are supported only for backward compatibility. |
|
- interrupts: |
|
- Must contain three elements for the standard variant of the IP |
|
(marvell,armada-3700-uart): "uart-sum", "uart-tx" and "uart-rx", |
|
respectively the UART sum interrupt, the UART TX interrupt and |
|
UART RX interrupt. A corresponding interrupt-names property must |
|
be defined. |
|
- Must contain two elements for the extended variant of the IP |
|
(marvell,armada-3700-uart-ext): "uart-tx" and "uart-rx", |
|
respectively the UART TX interrupt and the UART RX interrupt. A |
|
corresponding interrupt-names property must be defined. |
|
- For backward compatibility reasons, a single element interrupts |
|
property is also supported for the standard variant of the IP, |
|
containing only the UART sum interrupt. This form is deprecated |
|
and should no longer be used. |
|
|
|
Example: |
|
uart0: serial@12000 { |
|
compatible = "marvell,armada-3700-uart"; |
|
reg = <0x12000 0x18>; |
|
clocks = <&uartclk 0>; |
|
interrupts = |
|
<GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, |
|
<GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
|
<GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
|
interrupt-names = "uart-sum", "uart-tx", "uart-rx"; |
|
}; |
|
|
|
uart1: serial@12200 { |
|
compatible = "marvell,armada-3700-uart-ext"; |
|
reg = <0x12200 0x30>; |
|
clocks = <&uartclk 1>; |
|
interrupts = |
|
<GIC_SPI 30 IRQ_TYPE_EDGE_RISING>, |
|
<GIC_SPI 31 IRQ_TYPE_EDGE_RISING>; |
|
interrupt-names = "uart-tx", "uart-rx"; |
|
};
|
|
|